1998 Mitsubishi 3000GT Logo

Related Topics:

A
Anonymous Posted on Jun 01, 2014

How do I remove the air plenum on a 1998 mitsubishi 3000GT

5 Related Answers

dustyboner

alex metro

  • 364 Answers
  • Posted on Oct 24, 2008

SOURCE: find Mitsubishi 3000GT computer

its under the dash, behind the radio. to get to it, you need to remove the panel on the side of the console.

5a3378a.jpg

Ad
shaggyrat

Christophe Thompson

  • 1224 Answers
  • Posted on Dec 06, 2008

SOURCE: 1998 Mitsubishi 3000GT. Need to

there is a door poper looks like a screw driver but with a snake tounge its thin and goes inbetween the door panel and door and pops the clips you might have to replace clips after this be gentle
there is probably 12 to 16 clips in door panel

and then when the power switches out the door should slide up and off the door

Anonymous

  • 85 Answers
  • Posted on Apr 29, 2009

SOURCE: how many timing belts are on a 1998 mitsubishi

There is only 1

Anonymous

  • 49 Answers
  • Posted on Apr 15, 2010

SOURCE: location of map sensor on 95 3000gt.It not on

map stands for manifold absolute pressure. its located on the intake manifold just after the throttle body.

HondaCRX

Dan Martin

  • 252 Answers
  • Posted on Jun 23, 2010

SOURCE: 98 Mitsubishi 3000GT air conditioning does not blow cold

Could be a blockage. Get an air-con specialist to blow the lines out. Check for any leaks from the rubber pipes. The twisting nature of AC pipes in cars can perish and if you have heard a blow out (like a tire blowout) the air con might have blown through a pipe.

Any leaves trapped in the windshield/hood gutter?

Testimonial: "Thank you for your quick response."

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

6g74 engine montero 2001

the fuel pump is electrical high pressure pump and is located either next to the fuel tank or inside the fuel tank depending on the exact model the pump is cylindrical and if outside the tank will have wiring connector running to it
0helpful
1answer

Where can I get a new clockspring for a 1998 Mitsubishi 3000gt?

You will have to order clock spring from mitsubishi dealer or you can order it from autozone service center.But most probably, you will get it from dealer. The cost will be near to $220.------------ This is the procedure to replace clock spring.1) Disconnect battery and wait 5 minutes...
2) Use a 10mm socket to remove 4 airbag bolts on back of steering wheel assembly, remove airbag.
3) Remove steering wheel nut and pull out steering wheel (need puller?)
4) Remove center console to locate where clockspring line connects to airbag computer.
-------------- Click this link directly for complete removing procedure:--- http://technoanswers.blogspot.com/2011/04/how-to-remove-clock-spring-and-airbag.html -------------- This will help.Thanks.Helpmech.
2helpful
1answer

98 Mitsubishi 3000GT air conditioning does not blow cold

Could be a blockage. Get an air-con specialist to blow the lines out. Check for any leaks from the rubber pipes. The twisting nature of AC pipes in cars can perish and if you have heard a blow out (like a tire blowout) the air con might have blown through a pipe.

Any leaves trapped in the windshield/hood gutter?
4helpful
1answer

How do I change the spark plugs on a 3000 gt

The forward plugs are no problem as there easy to access. To get top the rear bank of plugs you'll need to disconnect the cable from the throttle body, remove any associated wiring, spark plug cables (remember what goes where) and hoses and remove the plenum (the large aluminum item on top of the engine which air travels to the intake. If my memory serves there are @ (8) No. 12 socket nuts/bolts that are used to hold the plenum in place. Also the plenum is supported by a bracket ot two located near the fire wall. If you take your time, mark all of your connections and be patient you can do this in an afternoon. Be certain to pick up an new gasket that runs between the plenum and intake. Also you'll be working with aluminum... go easy and take care not to over torque any nuts/bolts. For safety always start by removing the battery's ground cable.
I hope this may have helped,
Tom
0helpful
1answer

Need 1998 mitsubishi 3000gt wiring diagrams

go to gtouk.com and buy a manual all the info ever needed is inside.
0helpful
1answer

Emissions Inspection Problem on 1998 3000gt. Gets a NO PASS/ NO FAIL. Not Ready Reading. What now? tks. JJ

you need a tune up. replace all spark plugs and spark plug wires.change air filter .make sure egr valve is working right.check oxygen sensor. check all vacuum lines.
3helpful
1answer

I need a free wiring diagram for 1998 mitsubshi 3000gt

If you are unable to find the answer here, try your local library. They have every mechanical diagram for every car in alphabetical order. This is what I needed to do when the dealership wouldn't print off the wiring diagram for my VW Passat.
0helpful
1answer

Mass air flow sensor

<SOHC, Federal - Non Turbo,Canada - Non Turbo>

1d0cd9b.jpg ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------=====================================================================================================================================

<California - DOHC Non Turbo, Turbo>


c4dfca0.jpg

Not finding what you are looking for?

61 views

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...