2003 Volkswagen Passat Logo

Related Topics:

A
Anonymous Posted on May 28, 2014

EPC IS ON AND CODE PO 0322

Car stalls when reaching operating temp

3 Related Answers

Anonymous

  • 2120 Answers
  • Posted on Nov 02, 2008

SOURCE: epc light

Loose gas cap?

Ad

Anonymous

  • 518 Answers
  • Posted on Jul 04, 2010

SOURCE: when the engine reach its temp,car stalls when

fuel starvation,jets blocked,dirty fuel=water in it ,fuel is vaperising in pipes or carb.

bcharais

bcharais

  • 278 Answers
  • Posted on Oct 11, 2012

SOURCE: 2002 vw passat epc light comes on and when slowing down engine shuts down showing code 0322 what is my problem

Code P0322 states: Ignition/ Distributor Engine speed input circuit NO SIGNAL. the sensor is on the left side(as you sit in the vehicle) of the engine block near the transmission flange. Know this, codes do not tell you if the part is bad necessarily just where to look. Wires and connectors can fail too. I don't know how to test this sensor without a scan tool, the good kind. Which i don't have.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2helpful
1answer

2003 grand marquis trouble code po 128. Heater works. 100 mile trips no problem. Temp gage below C. New sensor or new thermostat?

Well code 128 is for a thermostat problem in the fact the engine is not reaching normal temp. If you have heat the engine is warming up but still may not be getting to normal range. Normal is 190 - 210 degrees.
I would replace the thermostat first and see what happens.
0helpful
2answers

P0410

Take it to a qualified repair shop an have it diagnosed properly !
0helpful
1answer

2002 vw passat epc light comes on and when slowing down engine shuts down showing code 0322 what is my problem

Code P0322 states: Ignition/ Distributor Engine speed input circuit NO SIGNAL. the sensor is on the left side(as you sit in the vehicle) of the engine block near the transmission flange. Know this, codes do not tell you if the part is bad necessarily just where to look. Wires and connectors can fail too. I don't know how to test this sensor without a scan tool, the good kind. Which i don't have.
0helpful
1answer
0helpful
1answer

At operational temp car stalls while stopping. new iac new plugs.

If it's an automatic, it could be the torque converter solenoid. Symptoms are stalling when coming to a stop after reaching speeds of 40mph and above. If it restarts immediately then stalls after putting in gear, that's what it is.
5helpful
2answers

Error codes po 134 po 153 po 154 po 155 po 171 po 174

PO 134 = 02 SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR1)
PO 153 =02 SENSOR CIRCUIT SLOW RESPONSE (BANK 2 SENSOR 1)
PO 154 =02 SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 2 SENSOR 1)
PO 155= 02 SENSOR HEATER CIRCUIT MALFUNCTION (BANK 2 SENSOR 1)
PO 171= SYSTEM TOO LEAN (BANK 1)
PO 174= SYSTEM TOO LEAN (BANK 2)
I WOULD SAY YOU HAVE FAULTY OXYGEN SENSORS CAUSING THE ENGINE TO RUN TOO LEAN REPLACE THEM AND YOU SHOULD BE BACK IN BUISNESS
1helpful
1answer

I have a 1991 buick regal stalls and shut off after warming up

egr valve is not opening up when the engine reaches it normal operating temperture
Not finding what you are looking for?

49 views

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Bradley
Bradley

Level 2 Expert

105 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...