How do i remove shifter form 1982 f250 4speed transmission

The motor home motor is probably a 454. I have seen the 6.2/454 engine exchange so the transmissions should be interchangeable. The shifter linkage and downshift cable may need a little adjustments.

a/t
or m/t
we cant guess this.
auto or stick. ?

on top of transmission you can see the shifter cable remove it from lever. Try to move lever freely try to move the shifter if it stuck again
could be cable or transmission internal
hope it helps

Front Floor Console Replacement Removal Procedure
1. Remove the console trim plate. 2. Remove the left console trim panel. . 3. Remove the right console trim panel. 4. Remove the floor console compartment.

5. If equipped with an automatic transmission, remove the 4?screws?(1), attaching the console?(2) to the shifter assembly?(3).

6. If equipped with a manual transmission, use a flat-bladed tool to disengage the retaining tabs?(1) attaching the manual transmission shifter boot assembly?(2) to the console. 7. Remove the manual transmission gear shifter knob, if necessary. 8. Remove the manual transmission shifter boot assembly?(2) from the shifter, if equipped.

9. Disconnect the console wiring connector?(1) from the inner console.

10. Remove the two nuts?(1) attaching the floor console?(3) to the vehicle floor. 11. Remove the two screws?(2) attaching the front of the console to the instrument panel assembly. 12. Remove the accessory power receptacle. 13. Lift the rear of the console upward and remove from the vehicle. 14. Remove the floor console armrest hinge, if necessary. 15. Remove the center console end panel.

16. Remove the screw?(2) attaching the floor console rear air duct?(3) to the floor console?(1). 17. Remove the floor console rear duct?(3) from the floor console?(1). 18. Remove the console storage bin, if necessary. 19. Remove the console lamp. 20. Remove the console compartment lamp switch.

josh zehnie, The first thing you have to do is pull the carpet away from the shifter boot. You will see a screw on each corner of the boot that have to be removed. Lift the shifter boot and the gasket under it straight up as far as possible. You will now see the top of the transmission where the shifter connects. Again you will four bolts holding the plate that the shifter goes through. Remove these bolts, which are usually allen key type heads, and gently pull the shifter straight up being careful that you don't drop the plastic bushings into the transmission that are on each side of the bottom of the shifter. Reassembly is just as easy. Just be careful that you get the bushings back in place. Test the shifter before you replace the upper boot. Good luck with this.

Neutral Park/BackUp Lights Switch - REPLACEMENT & ADJUSTMENT

1. Remove the console trim from the console.
2. Disconnect the electrical connector from the switch.
3. Remove the 2 attaching screws from the switch and remove the switch.

1. To install a new switch:
   1. Place the switch onto the transmission control shifter and loosely install the attaching screws. Position the transmission control shifter assembly in the N notch in the detent plate.
   2. Assemble the switch to the transmission control shifter assembly by inserting the carrier tang into the hole in the shifter lever.
   3. Install the attaching screws and tighten.
   4. Move the transmission control shifter assembly out of N position. This will shear the switch internal plastic pin.
      
   
   
2. To install the original switch:
   1. Place the switch onto the transmission control shifter and loosely install the attaching screws. Position the transmission control shifter assembly in the N notch in the detent plate.
   2. Rotate the switch on the shifter assembly to align the service adjustment hole with the carrier tang hole. Insert a 3 / 32 in. (2.38mm) diameter gauge pin to a depth of 9 / 16 in. (15mm) and tighten attaching screws.
   3. Remove the gauge pin.
   
   
3. Connect the electrical connector to the switch.
4. Install the console trim to the console.

Fig. 1: Neutral start/back-up light switch

Hope this helps (remember to rate and comment this).

This is most likely due to a mis adjusted or worn shifter mechanism. Clean it inspect it replace worn parts, lube and adjust.
Adjustment is done with shifter in neutral, there is an alignment hole thru all the arms and the bracket, adjust the length of the arms until a drill bit will insert thru the hole.

You should be able to take the trim screws around the shifter boot off and raise the boot. There are a few bolts on top of the tranny to remove and the shifter will come off. That is the only way to remove the shifter, it bolts into the top to make sure you can't just **** up on the shifter and pop it out of the shift forks.

I'm assuming you mean the 5-speed manual transmission. You've got to pull the carpet back around the shifter, remove the bezel that holds down the rubber boot, then remove the 10mm (I think) bolts that hold down the shifter ... lift the shifter out and add the transmission oil.

The lower shifter boot is attached to the transmission by 3 10mm bolts. You will need to remove to center consoule and the upper shift boot that attaches to the car to be able to remove the lower boot. Then you can replace the lower boot.