How to replace t100 rear pinion seal? - 1990 Chevrolet K1500

Sounds like a problem with your differential. The pinion bearing may be failing and the pinion is moving in and out on acceleration and deceleration. Check for oil leak and movement in the pinion shaft and also for backlash in the differential carrier

If you are talking the rear pinion seal, it isn't too bad at all. You just have to drop the drive shaft, remove the pinion nut and pull the pinion, then knock out the old seal and hammer in the new one. Going back together is just the reverse but you have to torque the pinion nut to the specified setting. As long as you are not removing the pinion gear you do not need to worry about setting the rear end up or worry about the crush sleeve.

This is not really a job for a novice. You will have to remove the rear drive shaft from the pinion, remove the pinion nut and the pinion itself, then remove the seal and replace with a new one. The tricky part is getting the pinion replaces and getting the correct torque setting without changing the pinion depth and compressing the crush sleeve more than spec.

There are few help links showing exact accurate procedure to replace Rack and Pinion. Click the link below and follow the procedure:-----
Pinion Seal Replace on Dodge Dakota? http://howtobyme.blogspot.in/2012/04/pinion-seal-replace-on-dodge-dakota.html

-----------

How to Replace a Rear Pinion Seal.
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-pinion-seal.html
------------

How to replace Power steering rack and pinion gear on Chevy Silverado 2500 HD? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html

----------
How to replace Power Rack and Pinion Steering Gear on Acura Car Models? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html

-----------
How to replace power rack and pinion steering gear on Toyota cruiser? http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-power-rack-and-pinion.html

----------

How to replace Power Rack and Pinion Steering Gear on Acura Car Models? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html


------------
Front Drive Pinion Seal Removal on Ford Explorer? http://repairhelpcenter.blogspot.in/2012/03/front-drive-pinion-seal-removal-on-ford.html

-------------
How to Replace Driveshaft, Pinion Flange & Seal?

http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-driveshaft-pinion-flange.html

------------

How to Replace Power Rack & Pinion Steering Gear On 2007 Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html


----------
How to Remove Power Rack & Pinion Steering Gear on Ford Windstar? http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-power-rack-pinion.html

-----------

Power Rack & Pinion Steering Gear replacing details for Buick Park Avenue and Pontiac Bonneville

http://repairhelpcenter.blogspot.in/2012/03/power-rack-pinion-steering-gear.html

-------------

How to Replace Power Rack & Pinion Steering Gear on Mercedes Benz Truck? http://howtobyme.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html


---------
How to replace Power Rack & Pinion Steering Gear on Toyota 4Runner? http://howtobyme.blogspot.in/2012/03/how-to-replace-power-rack-pinion_27.html

-----------

Power Rack & Pinion Steering Gear Replacing on Toyota Land Cruiser & Sequoia? http://schematicsdiagram.blogspot.in/2012/03/power-rack-pinion-steering-gear.html

----------
Power Rack & Pinion Steering Gear Removal on Toyota RAV4? http://repairhelpcenter.blogspot.in/2012/03/power-rack-pinion-steering-gear-removal.html

----------
How to Replace Power Rack & Pinion Steering Gear on Toyota Sienna? http://technoanswers.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html

------------
These details will help.
Thanks.

go to the web link below, it is a jeep owner forum, it explains how to do the job with pictures.
http://www.cherokeeforum.com/f51/how-replace-rear-pinion-seal-5869/

You'll need to remove the yoke from the rear end, you can use a seal removal tool, to remove the seal. Make sure you properly torque the nut down that holds the yoke on.

PINION FLANGE & OIL SEAL

CAUTION: Following procedure must be used to retain proper pinion bearing preload. Failure to follow procedure may result in premature axle assembly or component failure. Ensure pinion bearing preload is checked before disassembly, as previous pinion bearing preload will be used during reassembly.

Removal

1. Raise and support vehicle. Scribe reference mark on drive shaft-to-pinion flange on differential for reassembly reference. Remove bolts and "U" joint straps at pinion flange on differential.
Disconnect drive shaft from differential.
2. Remove rear wheels and brake drums to prevent any drag that may affect pinion bearing preload reading. Using INCH-lb. torque wrench, measure amount of force required to rotate pinion. This is pinion bearing preload. Record pinion bearing preload for reassembly reference.
3. Using Holder (6719), hold pinion flange. Remove pinion nut and washer. Scribe reference mark on pinion flange-to-pinion for reassembly reference. Using appropriate puller, remove pinion flange from pinion. Remove oil seal from axle housing.

Installation

1. Ensure oil seal surface in axle housing is clean. Coat lip of oil seal with gear lube. Install oil seal using appropriate seal installer. Drive oil seal into axle housing until oil seal installer contacts axle housing.
2. Install pinion flange on pinion with reference mark aligned. Using appropriate pinion flange installer, install pinion flange on pinion.

CAUTION: Washer must be installed on pinion with convex side of washer facing outward (away from pinion).

3. Install washer on pinion with convex side of washer facing outward (away from pinion). Install NEW pinion nut. Tighten pinion nut to 210 ft. lbs. (285 N.m). Rotate pinion several times to seat pinion bearings.

CAUTION: DO NOT overtighten or loosen then retighten pinion nut when adjusting pinion bearing preload. If pinion nut is overtightened, collapsible spacer on pinion must be replaced.

4. Rotate pinion using INCH-lb. torque wrench. Rotating torque should be equal to reading recorded in removal step 2) , plus 5 INCH lbs. (.056 N.m). If rotating torque is low, tighten pinion nut in small increments until proper rotating torque is obtained.
5. To install remaining components, reverse removal procedure using NEW "U" joint straps and bolts. Ensure all reference marks are aligned. Tighten bolts to specification. Check lubricant level and add if necessary.

Here is a guide on how to change the rear seal and bearings on a ford mustang
http://fhmotorsports.blogspot.com/2013/07/how-to-change-rear-axlewheel-seal-and.html

check your rear diff vent if pluged clean it out and clean up the pinion seal.sometimes if the leak is caused by pluged vent and has not been leaking long once vent is clean sometimes the leak will stop.there is not a specific torque amount because it is rotational torque(how hard to turn pinion).there is a crush sleve on the pinion and if torqued too tight or too loose brg preload will be wrong and brg damage could result.mark and remove drive shaft.remove rear wheels,brakes,axles.so when turning pinion you dont have any drag from brakes or axles.mark the position of the yoke on the pinion.remove yoke,replace seal,reinstall yoke be sure to replace pinion nut.tighten nut until it takes the exact same amount of force to turn pinion as before taking original pinion nut off.hope this helps.

with a puller