Question about 2003 Chevrolet Silverado 2500HD

1 Answer

Should the transmission be able to free wheel when in reverse with engine off,also free wheels when in drive (i beleive tranny is bad)

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 64,733 Answers

No only in NEUTRAL

Posted on Aug 25, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
dennymulford

Dennis Mulford

  • 1055 Answers

SOURCE: in 4 wheel drive front wheels wobble bad

i had the same problem,i endend up changing the hub bearings and ball joints and front u joints the main problem was the hub bearings

Posted on Feb 24, 2009

csmock132

Clint Smock

  • 4669 Answers

SOURCE: 1993 Chevy Silverado

Replace the vehicle speed sensor, it's located in the tailhousing of the transfercase

Posted on Feb 27, 2009

Anonymous

  • 7 Answers

SOURCE: truck only goes in reverse

You are going to need to either replace the tranny or rebuild it from the sound of it. The one possiblity is that you are low on fluid. If that is the case it could be causeing your problems

Posted on Aug 25, 2009

emissionwiz

Marvin

  • 85206 Answers

SOURCE: I have a 1988 chevrolet cheyenne 1500 pickup with

this can be cuased by a stuck transfer case, this can be cuased by dirty worn out fluid, has the transfer case ever been serviced? if not change the fluid and drive it for a day ofr so this will free up the transfer case clutch. It uses DEXRON 6 ATF

Posted on Nov 20, 2009

karelessloks

  • 1 Answer

SOURCE: 1997 chevy tahoe 4 wheel drive transmission

my trucks transmission shifts hard and slips only sometimes

Posted on May 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

E150 ford van, it has reverse but no forward. 5.0 engine with I beleive a c6 transmission.


FIRST CHECK THE TRANS FLUID. IS IT DARK BROWN OR BLACK AND SMELL BAD? IF SO CLUTCHS ARE BURNED UP. TIME FOR A REBUILD

Dec 19, 2014 | Ford Cars & Trucks

1 Answer

99 Dodge Caravan transmission is not wanting to go into reverse


the reverse work when you raise the car because is no force to the wheels

Sep 07, 2014 | Cars & Trucks

1 Answer

1999 Montero Sport XLS jerking into reverse. Error Code says change Transmission Fluid Temperature Sensor


Hi Sc, The job is labour intensive and may solve the problem. I wonder if the fluid in the tranny has ever been replaced? It's meant to be replaced at least once a year. If it smells burned have it replaced. Ask your shop to check the gearbox and engine mountings and in the event of your vehicle having rear wheel drive, the universal joints on the prop shaft. Regards John

Feb 23, 2014 | Mitsubishi Montero Sport Cars & Trucks

1 Answer

How do you remove a transmission from a 1994 plymouth acclaim?


If this is front wheel drive (most likely is; will have drive axles in front leading toward engine and tranny).

1. Raise and secure the front of vehicle on stands, and drain tranny fluid into a pan or bucket.

2. Remove tire and tranny side drive axle.

3. Disconnect all components connected to transmission (shifter cable) and any sensors, wires or wiring harnesses.

4. With a jack secure the transmission from underneath. (do not jack up tranny, merely put a very slight pressure to hold in place)

5. take out all transmission bolts that securet the transmission to the block (engine). If there is enough room, slowly lower the jack (another person secures transmission from top (keeping it balanced), and pull the transmission out. Be careful that the torque converter does not fall - it is heavy and may come out with transmission. (usually bolted to flywheel, also known as flexplate). This will have fluid as well in it, and will need to be drained (most of it).

Installation is reverse; also, if no room to drop tranny, two people can easily lift it from the top. (Cherry picker recommended.)

Please let me know if you need further assistance.

carsandcomps,

Guru, Premium Expert @ Fixya.com

Jul 19, 2010 | 1994 Plymouth Acclaim

1 Answer

Tranny slipping?


Dose it make a normal sound when you start the engine, then more then likely fly wheel ok, anf it's going to be the transmission, if not normal it's the fly wheel.

Jul 14, 2010 | 2006 Chevrolet Express

1 Answer

Transmission multiple shifting/banging under load


start engine chock back of drive wheels ,put in reverse and then check oil level

Jul 02, 2010 | Lincoln Continental Cars & Trucks

2 Answers

2000 Kia Sportage No reverse in Auto Tranny after towing


the transmission is gone, it might of **** pass neutral and tough the reverse gear

Jul 29, 2009 | 2000 Kia Sportage

1 Answer

Change transmission instructions


this is for rear wheel drive only front wheel drives require removing axle shat and dropping tie rod end and lower ball joint to get tranny out. If you start this I will give tork setting when I know what you have as it is a lot of work to type this out.

First disconnect the battery, inside the cab pull shifter boot off and remove snap ring to remove shifter, next get a block to go under engine remove drive line bolts and be sure E-brake is set and block the wheels, next put bolts from driveline into the read differential in order so you will be able to find them next disconnect the two starter bolts from the starter and tie starter up as not to allow the starter weight to hang on the wires. Remove two bolts holding slave cylinder on let hang off the side do not lose the shaft out of slave. Next remove the transmission mount bolt out next pull four bolts out of transmission cross member, next remove 5 bolts out of bell housing now get a baggie and a couple of rubber bands and pull drive shaft slide baggie over the transmission tail shaft and put on rubber band on bag to keep from losing fluid move drive shaft out of the way. Next disconnect the Speedo cable and wiring harness the reverse switch is at the top so will have to drop the tranny down to keep from breaking wire. Once you have a gap between the transmission and engine put block under back of engine slide the transmission out let the front drop down then lift up on rear of transmission and slide the cross member out of the way. Next slide tranny out of the way next remove the 6 bolts on the clutch assembly turning each bolt 1 and a ½ turns each till clutch is loose remove the clutch pressure plate and the throw out bearing, remove flywheel take to machine shop and have surfaced, replace the clutch plate pressure plate and the throw out bearing reinstall in reverse if you see any oil leaks replace seals, also replace rear transmission seal now if you don’t it will leak next after it is back together be sure you put new fluid in the transmission and bleed the slave cylinder.

Jun 28, 2009 | Nissan Pickup Cars & Trucks

1 Answer

Auto transmission slips then grabs


first thing i would try is changing the transmission fluid out and filter, i beleive its almost 8 quarts. use a full quart of lucas transmission additive with the new fluid. if this doesn't help, the transmission will either need replaced or rebuilt

May 24, 2009 | 1996 Ford Probe

3 Answers

Hello, 1986 Toyota 4X4 Truck 22R carb engine manual transmission. My son was driving it and the rear wheels locked up. Driving in 2 High mode. He got the truck pulled over to the side of the road using 4X4...


I've seen a similar issue on other transmissions where the shifter slips out of the slots in the shift forks, either due to shifter bushing wear or just general wear on tte trans. It can usually be remedied at least temporarily by popping the shifter top off the trans and resetting the forks all back to nuetral and then reinserting the shifter. It gets jammed when two forks are trying to engage two different gear sets.
On one of the 4x4 sites, they tell you how to replace the shifter bushings, cheap fix if you are lucky.
Good luck.

Dec 09, 2008 | 1986 Toyota Pickup 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...