- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
eBayhttps://www.ebay.com > itm
2009-2012 FORD FLEX MULTIFUNCTION BODY CONTROL MODULE BA8T-15604-AA BA8T15604AA. 2009-2012 FORD ... Located in: Rosenberg, Texas, United States. Delivery:.
US$89.99 · In stock
no body size told, extended cab or ????
ext cab is
BCM should be located on passenger side kick panel (under glove box to the right). You have to remove a panel.
2007 service manual remove it page, clear as day
Remove the radio bezel. Refer to Radio Replacement .
Disconnect the body control module (BCM) electrical harnesses.
Remove the BCM from the instrument panel (I/P) retainer:
3.1. Pry the BCM tabs from the locking tabs on the underside of the restraint.
3.2. Slide the BCM out of the retainer
The BCM needs to be programmed if replaced !
The body control module (BCM) must be programmed with the proper RPO configurations. The BCM stores the information regarding the vehicle options and if the BCM is not properly configured with the correct RPO codes, the BCM will not control all of the features properly. Ensure that the following conditions exist in order to prepare for BCM programming:
• The battery is fully charged.
• The ignition switch is in the ON position.
• The data link connector (DLC) is accessible.
• All disconnected modules and devices are reconnected before programming.
The following procedures need to be performed to properly configure a BCM:
BCM Programming
Passlock Learn
Program Key Fobs
Body Control Module (BCM)
In the center of the I/P, behind the HVAC control module
Important: Perform new BCM setup when you replace Body Control Module (BCM). Refer to Body Control Module (BCM) Programming/RPO Configuration .
Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
Remove the left instrument panel insulator. Refer to Instrument Panel Insulator Replacement in Instrument Panel, Gauges and Console.
Disconnect the BCM electrical connectors.
Push the BCM up and move the bottom of the BCM away from and out of the mounting bracket slot in order to remove the BCM.
During Body Control Module (BCM) related service, the procedures below are designated to set-up the BCM correctly. Before you start, read these procedures carefully and completely.
Setup New Body Control Module (BCM)
Tools Required
Scan Tool (Tech 2) GM factory scan tool !
Important:
• Read this procedure carefully and completely.
• The BCM will not function properly if the Setup New BCM procedure is not performed.
• Perform the Theft Deterrent Re-learn procedure after successfully finishing the Setup New BCM procedure. If the Theft Deterrent Re-learn procedure is not performed after a BCM replacement, the following conditions may occur:
- The vehicle will not be protected against theft by the PASSLOCK system.
- The engine will not crank nor start.
Your best bet is to take your vehicle to a dealer or a ASE certified repair shop who has proper tools .
... V6 > Electrical > Body Control Module (BCM). 1999 CHEVROLET BLAZER 4.3L V6 : Electrical : Body Control Module (BCM), Price, Core, Total, Add to Cart ...
... V6 > Electrical > Body Control Module (BCM). 1999 CHEVROLET BLAZER 4.3L V6 : Electrical : Body Control Module (BCM), Price, Core, Total, Add to Cart ...
BCM --The Body Control Module is located on the right side of the vehicle and positioned under the instrument panel. In order to gain access to the module, it will be necessary to first remove the trim panel.
The "BCM" module on your van has become unreliable.
The BCM is the "Body Control Module" that all these systems go through. The issue is that these are cold soldered and after a time the solder joints break on the computer connection. It is located behind the fusebox underneath the steering wheel.
If you know someone who can solder. You can use an 8mm and a 10mm socket to remove the BCM. Open it up and resolder the joints with a soldering iron. After that everything should be fine.
It is easier than it sounds.
BODY CONTROL MODULE REMOVAL Disconnect battery negative cable. Remove lower steering column cover and knee blocker reinforcement. Disconnect two wire connectors from bottom of Body Control Module (BCM) Body Control Module . Remove bolts holding junction block (fuse Panel) to dash panel mounting bracket. Remove junction block from mounting bracket. Remove screws holding BCM to junction block. Slide BCM downward to disengage guide studs on junction block from channels on BCM mounting bracket. Remove BCM from junction block.
Re-solder Main connection points INSTALLATION Reverse the preceding operation.
The "BCM" module on your van has become unreliable. The BCM is the "Body Control Module" that all these systems go through. The issue is that these are cold soldered and after a time the solder joints break on the computer connection. It is located behind the fusebox underneath the steering wheel. If you know someone who can solder. You can use an 8mm and a 10mm socket to remove the BCM. Open it up and resolder the joints with a soldering iron. After that everything should be fine. It is easier than it sounds.
BODY CONTROL MODULE REMOVAL Disconnect battery negative cable. Remove lower steering column cover and knee blocker reinforcement. Disconnect two wire connectors from bottom of Body Control Module (BCM) Body Control Module . Remove bolts holding junction block (fuse Panel) to dash panel mounting bracket. Remove junction block from mounting bracket. Remove screws holding BCM to junction block. Slide BCM downward to disengage guide studs on junction block from channels on BCM mounting bracket. Remove BCM from junction block. Re-solder Main connection points INSTALLATION Reverse the preceding operation.
×