How to install a center console on a pacifica

question edited for clarity.
Question moved to model category.

No, it just has the Integrated Power Module in the engine bay.

Chrysler Pacifica (CS; 2004-2008) fuses

Fuse-Box.info https://fuse-box.info > chrysler > chrysler-pacifica-cs-...

In this article, you will find fuse box diagrams of Chrysler Pacifica 2004, 2005, 2006, 2007 and 2008, get information about the location of the fuse panels ...

• 
  

  Fuse Box Diagram Chrysler

  https://fuse-box.info > Home > Chrysler
  Fuse box diagram (location and assignment of electrical fuses) for Chrysler 300 / 300C (Mk1/LX; 2005, 2006, 2007, 2008, 2009, 2010).

Chrysler Pacifica (crossover) (2003-2007) fuse box ...

imgVEHICLE.com https://imgvehicle.com > chrysler > fuse-box

An Integrated Power Module is located in the engine compartment near the battery. This center contains maxi fuses, mini fuses and relays. A label that ...

Chrysler Pacifica 2005 Fuse Box/Block Circuit Breaker ...

CarFuseBox https://www.carfusebox.com > chrysler-pacifica-2005-fu...

Apr 6, 2022 - Chrysler Pacifica 2005 Fuse Box/Block Circuit Breaker Diagram ; 2, C51 18LB/BR, Fused Rear Booster Fan Relay Output ; 3, W4 12BR/OR, Front

..

some models have an extra wire plug-in that would go to a light or temp controls on the very back of console. not all models have these options but all models have the extra plug-in. its cheaper for them to make one "fits all harness" than several different ones

On a warm day pull two side pieces off center dash. Remove shifter handle. Pull up on middle where it says PRND You should be able to reach in. If not there are a few screws inside and the cup holder and the middle will come off

The PCM on a 2004 Ford Mustang is a combined control unit, consisting of the engine control unit (also known as an ECU) and the transmission control unit.------------------------------------------------------------------------------------------
Launch X431 Master

Print I hope this helps you,good luck.Randy

Removal & Installation

Instrument Panel

1. Disconnect and isolate the battery negative cable.
2. Remove the center console closeout panel by removing the left and right attaching screws, then the left and right panels.
3. Remove or disconnect the following:
   
   Remove the shift bezel. Remove the transmission range indicator surround bezel. Remove the two screws attaching the front floor console to the lower instrument panel. Open the cup holder and remove the two attaching screws on the bottom of the cup holder. Open the bin and remove the two attaching screws on the bottom of the bin. Remove the front floor console sidewall attaching screws, three per side. Raise the front floor console and disconnect the wiring harness. Remove the front floor console from the vehicle.
   
   

   Fig. View of front floor console and shift bezel
   
   
   

   Fig. View of front floor console, showing attaching screws
   
   

4. Remove the floor console base assembly by removing the two screws attaching the L-brackets to the instrument panel.
5. Remove the nuts attaching the floor braces to the instrument panel.
   
   

   Fig. View of floor brace, attaching nuts, center brace, and floor bracket
   

I think that they are under the hood somewhere. I know that in some cars they put them on the left side of the center console. To look for these just open the driver door and there should be a place that pops out on the left. Hope this helps

Loosen the hex head set screw from the front of the Shifter knob. Pull it off, then remove the screws on the lower sides, as well as the ones hiding under the rubber cup holder. The entire assemble will now lift off.

There is a little black plug under the steering wheel near the center console. That little plug is the immobilizer I believe. If it is loose or missing, the car will not do anything, hopefully yours is laying in the floorboard somewhere!

Thats a DEALER ITEM or a salvage yard item.

it should either pop or screw out.