F150 2001 outside mirror

Could have a DDS an PDS .depends on what RPO code yours has >
Outside Mirror Description and Operation (with RPO DL3)
Or
Outside Mirror Description and Operation (without RPO DL3)
Without
Heated Outside Rearview Mirror Operation
The REAR DEFOG relay controls the operation of the heated outside rearview mirrors. When rear window defogging is requested, the REAR DEFOG relay is energized and B+ is applied to the supply voltage circuit of the mirror heater element, located in the mirror face. A constant ground is also applied to the mirror face. Current will pass through the mirror heater element, warming the mirror, so long as the rear window defogger is commanded ON.

With
Heated Outside Rearview Mirror
The DDS and PDS control the activation of the mirror heaters. Upon receiving a serial data message indicating a request for heated mirrors, the DDS and PDS, will apply voltage to the mirror heater element supply voltage circuit. The mirror heaters will remain active until a new message is received indicating rear defogger is to be deactivated.
The power mirror system consists of the following components:
• Driver Door Switch (DDS)--An electronic control module with integrated switches and requires programming when replaced
• Passenger Door Switch (PDS)--An electronic control module with integrated switches, requires programming when replaced
• Power Mirror Direction Switch--Integrated into DDS and is a four position momentary switch that provides a signal input to the DDS for up, down, left/extend and right/retract with a mirror switch activation
• Mirror Select Switch--Integrated into DDS and is a three position switch that allows the operator to select the left or right mirror and also a neutral/fold position
• Mirror Extend/Retract Switch--Integrated into DDS and is a two position switch that allows the operator to select the mirror extend or mirror retract position
• Left Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Right Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Body Control Module--An electronic control module that requires programming when replaced, serves as the power mode master and is the main message handler
• Horizontal and Vertical Position Sensors, if equipped with memory mirrors--Supplied a 5-volt and low reference by the DDS/PDS and provide a variable voltage signal to the DDS/PDS that is proportional to mirror position
• Folding Mirror Motor, in each of the outside mirrors, if equipped with power fold mirrors--Provides extend and retract movements of the mirror and is serviced as a complete mirror assembly
Your best bet mite be to take to a qualified repair shop , i really don't think you'll be able to do anything with it.
Do you have wiring diagrams so you know which wires to test ,do you know how to do electrical testing ?
The Driver Door Switch (DDS) and Passenger Door Switch (PDS) supply voltage to the outside rearview mirror heater elements upon receipt of a serial data message from the HVAC module indicating that the rear defrost system is active. The door switch supplies B+ through the driver/passenger mirror heating element supply voltage circuit when a request is seen. Ground is applied through the driver/passenger mirror heating low reference circuit.

glass and motor availbable separately

Removal
NOTE: Do not remove the mirror assembly when repairing the individual mirror part. Individual mirror parts can be installed without removing the mirror assembly.

1. Remove the front door trim panel; refer to Section 501-05.

1. Remove the outside rear view mirror access water shield.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect and remove the speaker.

1. Disconnect the outside rear view mirror electrical connector.

1. Remove the outside rear view mirror.
   1. Remove the nuts.
   1. Remove the outside rear view mirror.
      • Feed the outside rear view mirror wiring through the opening in the front door.

Hello, yes the glass can be replaced. you will need to see your local GM dealer for the glass. real simple to replace.

Carefully push the outside rearview mirror face on the inner edge, near the front door window glass, to allow access.

Insert a large flat-bladed screwdriver in the slot between mirror lens and the mounting base.

Grasp the mirror face firmly and pull it from the mirror body.

Remove the outside rearview mirror case from the outside rearview mirror housing and disconnect the heater wire, if equipped.

Using the palm of your gloved hand, press firmly on the center of the glass until the case seats onto the motor.

The mirror will make a snapping noise when properly seated.

Inspect the mirror for proper operation.

Power windows an locks work ok ? Do you know anything about automotive electeronic control modules ?
Power Mirror System
Power Mirror System Components
The power mirror system consists of the following components:
• Driver Door Switch (DDS)--An electronic control module with integrated switches and requires programming when replaced
• Passenger Door Switch (PDS)--An electronic control module with integrated switches, requires programming when replaced
• Power Mirror Direction Switch--Integrated into DDS and is a 4 position momentary switch that provides a signal input to the DDS for up, down, left/extend and right/retract with a mirror switch activation
• Mirror Select Switch--Integrated into DDS and is a 3 position switch that allows the operator to select the left or right mirror and also a neutral/fold position
• Left Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Right Outside Power Mirror--Contains both the vertical and horizontal mirror motors
• Body Control Module--An electronic control module that requires programming when replaced, serves as the power mode master and is the main message handler
• Memory Switch, if equipped with memory mirrors--Supplied power by the DDS and provides a voltage signal to the DDS upon a switch activation
• Horizontal and Vertical Position Sensors, if equipped with memory mirrors--Supplied a 5-volt and low reference by the DDS/PDS and provide a variable voltage signal to the DDS/PDS that is proportional to mirror position
• Powertrain Control Module (PCM), if equipped with memory mirrors--An electronic control module that requires programming when replaced and provides the message indicating transmission gear selection
• Driver Information Center (DIC), if equipped with memory mirrors--Part of the instrument cluster which is a an electronic control module that requires programming when replaced and is used to personalize the memory recall functions
• Fold Motor, in each of the outside mirrors, if equipped with power fold mirrors--Provides extend and retract movements of the mirror and is serviced as a complete mirror assembly
Each of the outside power mirrors contains 2 reversible motors to provide horizontal and vertical movement of the mirror glass. The vertical motor operates the up and down directions and the horizontal motor operates the left and right directions. If equipped with power folding mirrors, each outside power mirror will contain a reversible fold motor to operate the extend and retract functions. Each of the mirror motors are circuit breaker protected.

Do you know what DTC'S - diagnostic trouble codes are ?
DTC B1023
Circuit/System Description
The driver door switch (DDS) and front passenger door switch (PDS) each contain switches that control power door lock and window functions. The DDS also contains the control switch for the power outside rear view mirrors. These switches are integrated within the door control modules and are not serviceable as separate components. The DDS and PDS monitor these switch inputs for internal faults and set B1023 00 if any are detected.

You could have any number of problems an without testing , hooking up a scanner that can check DTC'S in the door module ,electrical circuit testing etc... we'd only be guessing . Your best bet mite be to take it to a qualified repair shop.

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation

1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
   

1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
   

1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
   

1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
   

1. To install reverse Removal procedure.
   

------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panels, Door Front—Town Car
Removal

1. Snap out two door pull strap retaining screw covers. Remove screws.
   

1. Remove three screws on front and rear side and center of front door trim panel (23942).
   

1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
   
   Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
   

1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
   
   Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
   

1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
   

1. Remove the door trim panel.
   

1. Disconnect two electrical connectors.
   

1. Remove nut from outside rear view mirror mounting base.
   

1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
   

1. Remove screw from outside rear view mirror base.
   

1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
   

1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
   

Mirror — Outside Rear View Removal
NOTE: Do not remove the exterior mirror assembly when repairing an individual part. Individual components can be installed without removing the exterior mirror.

1. Disconnect the battery ground cable (14301).

1. Remove the front door trim panel; refer to Section 501-05.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect the electrical connector.
   1. Remove the speaker.

1. Remove the outside rear view mirror (17682).
   1. Disconnect the power mirror wiring clips.
   1. Remove the outside rear view mirror nuts.
   1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).

Installation

1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
   To install, reverse the removal procedure.

is it an aero mirror with no arms?
Or a trailer tow mirror with arms?
The glass is repalceable. It is mounted on a center post with a ball on it. The mirror has a socket on the back center.
It also has 2 jack srews (plastic) that go into the tiny motors that move the mirror. You can push and pull on the glass and they will retchet, it won't hurt them.

You have to pop the mirror off the ball.

It helps to heat the socket with a hair dryer to put the new one on.
Please rate as fixya if this solves your problem.

Glass — Outside Rear View Mirror
Removal

1. Remove the mirror glass.
   1. Position the mirror glass to obtain a gap at the outside edge of the mirror.
   1. Carefully pry the outside edge of the glass away from the mirror housing.

Disconnect the electrical connector


Connect the electrical connector


NOTE: Engage the center pivot before the four inserts.
Install the mirror glass.

• Engage the center pivot and the four inserts

1. Disconnect the negative battery cable.
2. Remove the outside rearview mirror garnish.
3. Disconnect the harness connector.
4. Remove the 3 bolts and the outside mirror.

To install:

1. Install the outside mirror and tighten the bolts to 60 inch lbs. (7 Nm).
2. Connect the wiring harness.
3. Install the mirror garnish.
4. Connect the negative battery cable

open the door, on the opposite side of the mirror there is an interior panel, remove it, there are 3 nuts in there remove those, the mirror should come off, if it is power be sure to unplug it.