How do i adjust the tightness of the power steering pump belt 2008 chrysler sebring 2.7

power steering pump belt fell off.,or loose/ fluid is low/ pump is shot/ power steering ram is wornout/damaged. did you hit/slide front wheel into a curb?

Here is a Diy guide to adding tension to your auxiliary belt, If your not confident, it's best to allow a qualified mechanic to do the task as if your dont have the correct tension, other problems could accuor and make the car un-driveable as it's likely the belt controls your cooling system too.

http://www.ehow.co.uk/how_7442911_adjust-alternator-belt-tension-gauge.html

go to www.automecanico.com translate this web with your browser
and get the topic.
God bless you

Thanks for using FixYa.

Fig. Accessory drive belt routing-2.7L engine
Chrysler Cirrus & Sebring Convertible; Dodge Stratus; Plymouth Breeze

Fig. Accessory drive belt routing-Chrysler 2.7L engine

2.7L Engine
A/C & Alternator Belt

1. Raise and safely support the vehicle.
2. Remove the right front wheel and belt splash shield.
3. Loosen tensioner locking bolt and pivot bolt.
4. Rotate tensioner clockwise to allow enough slack to remove belt

To install:

1. Install the air conditioning compressor/alternator belt on pulleys, tensioner in slack position, slip belt over idler last.
2. Adjust drive belt tension.
3. Install the belt splash shield and right front wheel.
4. Lower vehicle.
   
   
   

   Fig. Installing A/C & alternator belt-2.7L engine
   

1. Before servicing the vehicle, refer to the Precautions Section.
2. Raise and safely support the vehicle.
3. Remove the right front wheel and belt splash shield.
4. Loosen the tensioner locking bolt and pivot bolt.
5. Rotate tensioner clockwise to allow enough slack to remove the belt

To install:

1. With the tensioner in a slack position, install the Air Conditioning (A/C) compressor/alternator belt on the pulleys. Slip the belt over the idler last.
2. Adjust the drive belt tension.
3. Install the belt splash shield and right front wheel. Tighten the wheel lug nuts to 100 ft. lbs. (136 Nm).
4. Lower the vehicle.
   

Power Steering Belt

1. Raise and safely support the vehicle.
2. Remove the right front wheel and belt splash shield.
3. Remove the air conditioning compressor/alternator belt.
4. Loosen belt adjusting bolt. It is not necessary to loosen the pivot bolt on the power steering pump. There is a bushing incorporated into the power steering pump/bracket that allows it to pivot.
5. Remove the power steering belt.

To install:

1. Install the power steering belt on pulleys.
2. Adjust drive belt tension.
3. Install the air conditioning compressor/alternator belt.
4. Install the belt splash shield and right front wheel.
5. Lower vehicle.

Check the belt to see if it's tight enough and check the power steering fluid reservoir to make sure it's full to the full mark. If neither of these are the problem the power steering pump is the problem.

Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998
Power Steering Pump - REMOVAL & INSTALLATION

Cirrus, Stratus, Sebring Convertible and Breeze
(see Figures 1, 2, 3 and 4)

1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet, which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
2. Siphon as much power steering fluid out of the reservoir as possible.
3. Raise and safely support the vehicle.
4. Remove the right front tire and wheel assembly.
5. Remove the splash shield from the right front wheel well.

Fig. 1: Power steering pressure hose attachment to the pump-with Variable-Assist steering



Fig. 2: Power steering pressure hose attachment to the pump-without Variable-Assist steering

1. Disconnect the power steering pressure hose from the pump.
2. Remove the hose connection on the power steering pump.
   

Fig. 3: Typical power steering pump front bracket attachment

1. Remove the power steering adjusting bolt.
2. Remove the power steering pump rear attaching bolt.
3. If so equipped, remove the Anti-lock Brake System (ABS) hydraulic control unit heat shield.
4. Remove the wheel speed sensor retainer bracket from the right inner fender.
5. Remove the wheel speed sensor sealing grommet from the right inner fender.
6. Disconnect the speed sensor wiring.
7. Push the wiring through the hole in the inner fender.
   

If not equipped with anti-lock brakes, the hole will just have a sealing plug.

1. Remove the bolt attaching the power steering front bracket to the mounting bracket. Access to the bolt is gained through the hole for the speed sensor wiring.
2. Remove the power steering pump drive belt.
3. Remove the power steering pump and the front bracket as an assembly.
   

To install:

1. Install the power steering pump and bracket.
2. Reinstall the bolt at the adjusting slot, but do not tighten.
3. Reinstall the bolt mounting the power steering pump to the rear mounting bracket, but do not tighten.
4. Reinstall the power steering pump top bolt, but do not tighten.
5. Reconnect the power steering hoses.

Fig. 4: Install a new O-ring gasket on the hose fitting
Use a new O-ring when reinstalling the power steering pressure hose.

1. Reinstall the drive belt.
2. Adjust the drive belt and tighten the power steering pump bolts to 40 ft. lbs. (54 Nm).
3. Reinstall the splash shield.
4. Reinstall the tire and wheel assembly.
5. Lower the vehicle.
6. Reconnect the negative battery cable.
7. Refill the reservoir and bleed the power steering system.

Sebring Coupe and Avenger

1. Disconnect the negative battery cable.
2. Remove (drain, suction pump, etc.) as much power steering fluid as possible.
3. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.

Cover any components located underneath the power steering pump with a shop towel to protect them from damage due to power steering fluid spillage. For example, the A/C compressor or alternator, depending on vehicle and engine, is below the power steering pump, so cover the A/C compressor or alternator with a shop towel before removing any hoses.

1. Loosen (but do not remove) the power steering pump mounting bolts and remove the drive belt.
2. Remove the pressure switch connector from the side of the pump.
3. Disconnect the pressure line.
4. Unbolt and remove the pump from the mounting bracket.

To install:

1. Clean all parts well. Inspect the pump pulley for cracks. Check the hoses carefully for cracks or signs of weakness.
2. Install the pump, wrap the belt around the pulley and lightly tighten the mounting bolts.
3. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the fitting to 13 ft. lbs. (18 Nm).
4. Connect the return line and secure with the clamp.
5. Fasten the pressure switch connector.
6. Adjust the power steering belt for proper tension and tighten the adjusting bolts.

Use only MOPAR ATF PLUS automatic transmission fluid type 7176, ATF+3 automatic transmission fluid, or equivalent, in the power steering system of Sebring coupe and Avenger models.

1. Refill the reservoir and bleed the power steering system.

Hope this help to solve it (remember comment and rated this). TY for using Fixya.

Does the problem accure (1) when making a right turn only, or making a left turn only or (2) when turning in either direction. (1) sounds like rack and pinon while (2) sounds like power steering pump. (1) Rebuilt $125.00 and (2) Rebuilt $60.00

the belt will be on the front pulley on the power steering pump

you have two belts . put the large belt on first . it goes around crank pulley air conditioning pulley alternator pulley.loosen tension pulley to adjust belt. tension. then you put the other belt on power steering pump pulley and crank pulley. adjust belt tension loosen power steering pivot bolt. that it.