P0455 code Have a 2007 Chrysler pacifica 4.0 have code po455. Installed new purge solenoid but now my check engine light is bk on. So could it b my Evap System Integrity Monitor. All hoses r good.?

https://www.youtube.com/watch?v=L5K4guZ4ak8

Possible causes
- Missing or loose fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- EVAP canister or fuel tank leaks
- EVAP system hose leaking
- Fuel tank leaking
What does this mean? Tech notes
The P0455 it's a very common code, because the code is set if the gas cap is loose or missing. Start by tighten the gas cap and clearing the code. In most cases the code can be clear by disconnecting the car battery for about 30 minutes.
What does this mean? When is the code detected?
Evaporative Emission System (EVAP) control system has a very large leak such as fuel filler cap fell off, EVAP control system does not operate properly.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vapors
P0455 Mitsubishi Description
This diagnosis detects leaks in the Evaporative Emission System (EVAP) purge line using engine intake manifold vacuum. If pressure does not increase, the Engine Control Module (ECM) will check for leaks in the line between the fuel tank and EVAP canister purge volume control solenoid valve under the following vacuum test condition.
The vacuum cut valve bypass valve is opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP canister vent control valve will then be closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve is opened to depressurize the EVAP purge line using intake manifold vacuum. After this depressurization is implemented, the EVAP canister purge volume control solenoid valve will be closed.

Read more: http://engine-codes.com/p0455_mitsubishi.html#ixzz3NlVyARyX

Check all hoses and fittings from evap back to fuel tank. On 1post in pacifica world the prob was solved by dropping the fuel tank and replacing the fitting on one of the fuel pumps. Then clear the code and hopefully doesn't come back.

P0496 is not alisted code.
P0455 - Evaporative Emission Control System Leak Detected Gross Leak (fuel vapors)
Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vapors Possible causes - Missing or loose fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- EVAP canister or fuel tank leaks
- EVAP system hose leaking
- Fuel tank leaking

PO455- EVAP System
Gross Leak or No purge Flow

Gas Cap -Bad or just not on tight

Cracked Hoses
Purge Valve Stuck Closed
Canister Vent Solenoid Stuck Open
Fuel Tank Pressure Sensor

Check that gas cap is on, then after that
a repair shop

CODE PO455 - EVAP SYSTEM LARGE LEAK DETECTED CONDITIONS.POSSIBLE CAUSES FUEL CAP LOOSE MISSING,FUEL TANK FULLER NECK OR FUEL SENDING UNIT O - RING IS LEAKING, FUEL TANK PRESSURE SENSOR IS DAMAGED,FUEL TANK VAPOR LINES,CLOGGED,DAMAGED,OR DISCONNECTED,PURGE VALVE VAPOR LINE IS CLOGGED,DAMAGED,OR DISCONNECTED,PURGE SOLENOID IS NOT OPENING,IT MAY BE DAMAGED OR STICKING,VENT SOLENOID IS NOT CLOSING,MAY BE DAMAGED OR STICKING,PCM HAS FAILED.

P0441 Evaporative Emission Control System Incorrect Purge Flow
OBD-II Trouble Code Technical Description

Evaporative Emission Control System Incorrect Purge Flow
What does that mean?

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
Symptoms

Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes

A code P0441 could mean one or more of the following has happened:

* Bad vacuum switch
* Broken or damaged EVAP line or canister
* Open in PCM purge command circuit
* Open or short in Voltage feed circuit to Purge Solenoid
* Faulty purge solenoid
* Restriction in EVAP solenoid, line or canister
* Corrosion or resistance in purge connector
* Bad PCM

Possible Solutions

With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

* Common Chrysler fix - Replace Leak Detection Pump / LDP
* Repair damaged EVAP lines or canister
* Repair open or short in voltage feed circuit to Purge Solenoid
* Repair open in PCM purge command circuit
* Replace purge Solenoid
* Replace vacuum switch
* Repair restriction in Evap line or canister or soleniod
* Repair resistance in purge connector
* Replace PCM
THIS IS LIKELY FROM TOPPING OFF THE TANK EACH TIME YOU FUEL UP



P0455 is similar:

Technical Description

Evaporative Emission Control System Leak Detected (no purge flow or large leak)
What does that mean?

This indicates a fuel vapor leak or lack of purge flow in the EVAP control system. It means a large leak has been detected. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.
Symptoms

You likely won't notice any drivability problems.
Causes

A code p0455 most likely means one or more of the following has happened:

* A loose or improperly affixed gas cap
* A non-conforming gas cap (i.e. not factory/original brand)
* Other leak or damaged piece in EVAP system

Possible Solutions

With a p0455, the most common repair is to:

* Remove and reinstall the gas cap, have AutoZone clear the codes, and drive for a day and see if the codes come back.
* Otherwise, replace the gas cap, and/or
* Inspect the EVAP system for cuts/holes in tubes/hoses (you may hear a vacuum noise or smell fuel), repair if necessary

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

po455 is Probable Cause[s]

1. Defective, loose or missing fuel cap
2. EVAP canister broke, hose cracked or not connected
3. Purge or vent solenoid defective
4 . Vacuum leak at engine po121 code po121 means Throttle Position Sensor/Switch A Circuit Range/Performance Problem . it is usually indicative of a faulty throttle position sensor or faulty wiring harness in the engine bay.

P0455....Evaporative Emission Control System Leak Detected (gross leak
the first thin to check is your gas cap

p0455 is for evap leaks check hose on the passenger side by the fender under the hood a hose coming from the engine to the purge control valve one of the rubber hose is probably broken