How do i reset central locking on a almera tino 03 reg

First of all it sounds like your ign lock is sticking,when you take the key out of the lock turn the steering wheel to get the lock to click on,if that works,get some spray grease,not wd40,and spray into the barrel,thenn work the key in and out.That should also solve the problem resetting your key.

Does the central locking still work when you open with the key. First place to start is a new battery in ur fob even if the lights still coming on

406 FOB / PLIP PROGRAMMING :

The 406 deadlocking remote control has specific button controls, and if the vehicle has two controls, one is set as primary and the other as secondary.

When replacing the Plip, a Primary or Secondary Plip are different part numbers and must be ordered as required. The white label inside the Plip is labelled PRIM or SEC.

1. Turn the Ignition switch ON.

2. Press the large Plip key button (Primary Plip)

3. Within 10 seconds press the large Plip key button (Secondary Plip)

4. If there is one remote, press the Primary plip button twice.

5. Turn ignition OFF.

6. Test Plip's for correct operation.
NOTE : On some 406 models, Plips cannot be re-synchronised unless the battery has been disconnected for 1 minute

Try the following:

"KEY FOB PROGRAMMING
NISSAN
SYSTEM DESCRIPTION
The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and hazard reminder. When the doors are locked and
unlocked the unit flashes the hazard lights once for lock and twice for unlock.
A maximum of four remote controls are allowed to be programmed.
ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II
Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.
Procedure
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key?s.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key?s for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds."

Method 1: Press lock or unlock button 4 times in succession. Method 2: Switch ignition ON and OFF. Within 10 seconds press lock and unlock button in succession.
This is the only manual reset
If this does not work go to your local auto electrician
The probable fault could be central locking activator passenger door

before going any where get the service and repair manual from the given link it will save your time and money also http://toolsnyou.com/

if its the remote plips you mean, then the car may need recoded to the plips if the car battery has been disconnected or changed recently.

Otherwise the keyblades should still open the doors, or the central locking controller is faulty.

check the battery in the key control it may be faulty

central locking on my 93 corsa with standard key, not electronic type as used on later models, all doors are locked and refuse to open, ive checked fuse and thats ok, doors refuse to open from inside the vehicle and from outside, only the tailgate will open from the key, any ideas ,,, thanks dave

hello mate.. if it has stopped working you might want to check the battery first.. if you are sure that the battery is fine then consider reprogramming the fob to your car.. here are the steps to follow.. NISSAN

Remote Control Fob Procedures:

The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and emergency hazard reminders.

When the doors are locked and unlocked the unit flashes the hazard lights once for lock and twice for unlock.

A maximum of four remote controls are allowed to be programmed:

ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II

Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.

Procedure:
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Next, turn ignition switch to OFF position. Leave key in ignition switch.
3. Wait 2 seconds then the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds.

http://www.autokeysquad.com/nissan-fob-programming

i hope this can help you.. :)