How to remove front seats on 63 T-Bird

transfer case shift control module
Transfer Case Shift Control Module Replacement
Removal Procedure
Important: The transfer case shift control module (TCCM) is located under the drivers seat carpet. For removal purposes, access the TCCM from underneath the carpet.
Remove the drivers bucket seat or split bench seat. Refer to Front Seat Replacement - Bucket or Split Bench Seat Replacement.
Remove the left front sill plate. Refer to Front Side Door Sill Plate Replacement.
Remove the left hinge pillar. Refer to Body Hinge Pillar Trim Panel Replacement - Left Side.
Remove the left center pillar. Refer to Center Pillar Lower Trim Panel Replacement.

If ypu are talking about seat mounting, on bucket seats they only have two remove these move seat all the way back then tip seat forward to unhook front remove seat.

you could try removing the electric runners off your original seats and fitting them to your new seats

What year make and model? Are they electric or manual?

Well, this good to be interesting to say the least, and probably long as well. By my gm. service information your going to need to take out the front bucket seats so the sides of the console can come off.


Remove the left front seat . Refer to Bucket Seat Replacement .



1



Front Floor Console Extension Panel



2



Retainer Clip (Qty: 5) same for right side.


















Callout







Component Name






Preliminary Procedure

Remove the right front seat. Refer to Bucket Seat Replacement .







1





Front Floor Console Extension Panel







2





Retainer Clip (Qty: 5)








Front Floor Console Accessory Trim Plate Assembly


Procedure

Use a flat bladed plastic trim tool in order to release the console accessory trim plate from the console assembly.



2



Retainer Clips (Qty: 5)



Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement.



1



Front Floor Console Accessory Housing Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Accessory Housing Assembly


Procedure

1. Disconnect the electrical connectors.



2. When replacing the front floor console accessory housing assembly, transfer all necessary components

1. Remove the rght or left front floor console extension panel. Refer to Front Floor Console Extension Panel Replacement - Right Side or Front Floor Console Extension Panel Replacement - Left Side .



2. Remove the front floor console cup holder housing. Refer to Front Floor Console Cup Holder Housing Replacement .

1



Front Floor Console Rear Trim Panel Screw (Qty: 1)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Rear Trim Panel



3



Retainer Clip (Qty: 4)


Preliminary Procedures

1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .



2. Remove the right and left front floor console fillers. Refer to Front Floor Console Filler Replacement .

1



Front Floor Console Armrest Assembly Bolt (Qty: 4)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

9 N?·m (80 lb in)



2



Front Floor Console Armrest Assembly


Procedure

Position the armrest assembly out of the way leaving the electrical harness attached.



3



Front Floor Upper Console Trim Plate


Procedure

Lift the rear of the trim plate first, releasing the retainers securing the trip plate to the console assembly.



4



Retainer Clips (Qty: 4)



Front Floor Console Replacement (Enclave)




















Callout







Component Name






Preliminary Procedures

1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .



2. Remove the right and left front floor console extension panels. Refer to Front Floor Console Extension Panel Replacement - Right Side and Front Floor Console Extension Panel Replacement - Left Side .



3. Disconnect the automatic transmission range selector lever cable. Refer to Range Selector Lever Cable Replacement .

1





Front Floor Console Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)







2





Front Floor Console Bolt (Qty: 10)




Tip

Before installing the right lower forward bolt, ensure that the console wiring harness is tucked below the fastener location to avoid driving the bolt into the harness.




Tighten

9 N?·m (80 lb in)







3





Front Floor Console Assembly


Procedure

1. Note location and routing of the front floor console wiring harness prior to removal of the front floor console assembly to ensure proper reinstallation.



2. Disconnect the electrical connectors.



3. With the aid of an assistant remove the console assembly from the vehicle.



4. When replacing the front floor console, transfer all necessary components.
   

Do you have a bench seat or bucket seats. The difference between the two are: the bench seat is one seat, Bucket seats are individualy adjustible.

Front Seat Replacement - Bucket
Removal Procedure
Caution: Refer to SIR Caution in the Preface section.
Important: The front seat is equipped with a seat belt pretensioner. Disable the pretensioner before you perform any work on the seat.

1. Disable the SIR system. Refer to SIR Disabling and Enabling and to SIR Disabling and Enabling .
2. Remove the front seat head restraint. Refer to Front Seat Head Restraint Replacement .
3. Position the front seat to the full forward and the full-up position.
4. Remove the bolts from the rear of the seat adjuster.

Try to lift up the whole bucket seats from the drivers side towards the right. Use the back seatbelt to hang the bucket seats. The engine is right inside the front row seats. That is where you can remove the engine thru drop it down..

Hi, follow the instruction below......
Rear
See Figures 3, 4, 5 and 6

1. Remove the lower seat cushion by pulling straight up on the front portion and disengaging the clips. Then hinge the seat upward to release the rear clips.
   

Fig. 3: Pull up on the front of the lower seat cushion and disengage the clips

1. Remove upper rear seat back-to-chassis bolts.

Fig. 4: Remove the bolts behind the center armrest ...



Fig. 5: ... and the bolts on the lower corners ...



Fig. 6: ... Then pull up on the seat to disengage the three clips on the top of the seat

1. Remove rear seat back by tilting forward and pulling straight up.
   

To install:

1. Install the lower seat cushion and torque the lower rear seat-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm).
2. Install the upper rear seat back cushion and torque the upper rear seat back-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm)

2 bolts in the front and two in the rear of each seat, 10 minute job, disconnect wiring under seat, take care not to break the locks on the connectors for the power seats.