At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Remove the safety bolts located under the casing with a socket wrench. At the other end of the seat belt, remove the nut which holds it in place with a wrench.
Remove the shoulder harness of the seat belt with the wrench.Remove the bolt and nut which is attached to the anchor side of your old seat belt. This is at the bottom of the vehicle.Install the new anchor section of the seat belt.
If it's that tight it would be easier to remove the lower back seat and remove the 18 mm bolt and remove the seatbelt anchor. To remove the lower back seat pull up sharply on the front left and right sides of seat, only held in with plastic clips, then seat will pull forward and ouy
shoot the mouse !!!! ,,,, sorry coldnt resist ,,, you have to lift rear seatbase and boot carpet to get at the seat back bolts ,,, not a big problem ,,, the big one is getting at the seat belt because u have to remove alot of trim to get at the seat belt bolts ,,, alot of clips are involved that will break so source new clips before you start the job ,,,,rotten job so feel so sorry for you ,,,,
Hi Ray, Removal of the seat belts requires removal of the seats. Adjust the front seats to the fully backwards position and remove the fixing bolts and then unhook rails at the rear.You will notice a wire cable attached to each seat used to adjust the belt shoulder hight. This must also be disconnected. On later model vehicles there is an automatic retraction unit which pulls the driver and or passenger back into the seat in the event of the air bags being deployed. These connections must also be removed. If seats are electrically operated unplug all connectors. Remove seats and then gently remove plastic door pillar covers. (These are in two pieces for each front belt.) Removal will leave the fixing bolts of retractable part of the seat belt exposed. The buckle side is fixed with one bolt and has an electrical connection which must be disconnected. Hope this is of help? Regards John
I don't know if this is something you want to get into? You decide.
Front Seat Belt Replacement
SRS components are located in this area. Review the SRS component locations and the precautions and procedures before performing repairs or service.
NOTE: Check the front seat belts for damage, and replace them if necessary.
Front Seat Belt
Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
Slide the front seat forward fully.
Pull the lower anchor cover (A) back, and remove the lower anchor bolt (B).
Remove the B-pillar lower trim panel.
Remove the upper anchor cover (A), and remove the upper anchor bolt (B).
Disconnect the seat belt tensioner connector (A), and detach the harness clip (B) from the retractor (C). Remove the upper retractor mounting bolt (D), and the lower retractor bolt (E), then remove the front seat belt (F) and retractor.
If necessary, remove the front seat belt protector (G).
Remove the B-pillar upper trim.
Remove the shoulder anchor adjuster (A).
Install the seat belt in the reverse order of removal, and note these items:
Assemble the washers, collar, and bushing on the upper and lower anchor bolts as shown.
Check that the retractor locking mechanism functions.
Apply liquid thread lock to the anchor bolts before reinstallation.
If the seat belt tensioner has been activated, replace the front seat belt protector with a new one.
Before installing the anchor bolts, make sure there are no twists or kinks in the seat belt.
Make sure the seat belt tensioner connector is plugged in properly.
Reconnect the negative cable to the battery.
Enter the anti-theft code for the radio, and then enter the customer's radio station presets.
Reset the clock.
Do the PCM idle learn procedure and the power window control unit reset procedure.
Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
Remove the front seat.
If equipped, remove the center table.
Remove the under seat storage box.
Remove the center cover, driver's, passenger's.
Driver's: If equipped with seat heater, remove the harness band (A), and disconnect the seat subharness connector (B). If equipped without seat heater, detach the seat belt switch connector clip (C). Detach the seat belt buckle tensioner clip (D), and harness clip (E).
Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED
Description
Tool Number
Safety Belt Bolt Bit
T77L-2100A NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.
Removal
Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear
Sedan Removal
Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
Remove rear seat cushion from vehicle.
Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear
60/40 Split Bench—Sedan Removal
NOTE: Safety belt bolts do not secure seat back to vehicle.
Remove rear seat cushion as described.
Fold down back seat and remove two bolts in the center of each seat back striker plates.
Remove two bolts from outboard rear seat back frame retaining brackets.
Lift seat back up and pull forward to remove from vehicle.
Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan
Removal
Remove rear seat. Refer to Section 01-10 .
Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
Pull lower quarter trim panel away from body.
Remove safety belt retaining bolt.
Feed safety belt through lower quarter trim panel.
Remove safety belt anchor plate-to-sill bolt from quarter panel.
Remove retractor anchor nut and retractor from rear quarter panel.
Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
Slide anchor plate end of safety belt through the openings in the quarter trim panel.
Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.
Item
Part Number
Description
1
386277-S190
Bolt (Part of 611B68)
2
31012
Upper Rear Quarter Trim Panel
3
611B60
Retractor and Tongue
4
N800937-S190
Nut
5
389370-S190
Bolt
6
—
Rear Quarter Panel (Part of Body)
7
52018
Lower Rear Quarter Trim Panel
8
—
Mounting Stud (Part of Body)
Remove seat belt anchor bolt and retractor and tongue from rear deck panel.
Installation
To install, reverse Removal procedure.
Make sure the safety belt webbing is not twisted. If it is, remove the twist.
Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
×