Question about 2003 Toyota Tacoma

Open Question

How to remove front bumper 2003 toyota tacoma

I need to replace it cuz I bumped into a sidewalk upright bar that I didn't see

Posted by Anonymous on


5 Suggested Answers

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: front grill on toyota solara

That is correct - it worked for me - now the questions is - How do I remove the old logo ?

Posted on Apr 25, 2009

  • 37 Answers

SOURCE: replacing front struts on a 2007 toyota tacoma


Posted on Jul 25, 2010

  • 85178 Answers

SOURCE: how to remove Toyota camry 2003 front bumper bar

The video at this YouTube LINK outlines the bumper removal to change the headlights in this case.

Posted on Sep 07, 2012

  • 85178 Answers

SOURCE: 2003 camry front bumper bar

Duplicate question

Posted on Sep 07, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why doesn't it start?

Most fuel pump cut off switches on Fords are around the passenger front area inside the vehicle might be hidden by the carpet or a fuse cover .

Apr 23, 2016 | Ford Cars & Trucks

1 Answer

Violent shimmy in front end when occasionally going over a bump

Do you have a trac bar? If not, make sure you don't have a bent tie rod, if that's bit he case, Did look at your drag link and/or steering stabalizer next. If you do have a trac bar, I'd say it's most likely bump steer. Either take off your trac bar(which could actually be masking more problems than you're aware of) or adjust what need be to insure that your drag loo I and trac bar arE at the same angle. Bump steer is often caused because the drag link is either being pushed or pulled by the vertical suspension movement due to not being parallel with the trac bar. I hope I was of help to ya!

Jul 11, 2014 | 2000 Jeep Cherokee

1 Answer

Replacing anti-roll bar bushes citroen xsara picasso

anti-roll bar bushes, could be the problem get a big screw driver and lever the anti roll bar see if you have movement

Jun 02, 2013 | 2001 Citroen Xsara Picasso

1 Answer

Need to replace the harmonic balancer on a 1992 odlsmobile 98 regency

A harmonic balancer puller-cheap and easy to use-available at any auto parts store. The hardest part is getting the crankshaft pulley bolt loose. An impact tool is best, but not absolutely necessary. Old school way: not recommended, but I've done it this way: put a socket and long stout breaker bar on the crank bolt. Let the breaker bar end rest on the ground. Now use the starter to just bump the engine over one quick time-just one little bump is all it takes to loosen the crank bolt- if you positioned the breaker bar right. Good luck, Joe.

Sep 26, 2012 | 1992 Oldsmobile Ninety Eight Regency

1 Answer

I need to stop the pulleys from turning to remove the bolt on the hormonic balancer to replace the timeing belt on a 1993 toyota camry

here is a little trick I use to remove the balancer, take a breaker bar with correct size socket put it on the bolt then wedge the breaker bar against something solid, like the frame rail, then just bump the starter
DONT spin it just bump the key ONCE, this will loosen the bolt so it can be removed

Jul 24, 2012 | 1993 Toyota Camry V6

1 Answer

How do i replace the crankshaft sensor in my 1997 bonneville


In order to remove the damper you need to put the car on jackstands, remove the right wheel & inner fender splash shield, the drive belt and the lower bellhouseing cover plate stick a flat head screw driver in the teeth so you can loosen the crank nut.

I would NEVER tell you to use a six point socket on a breaker bar wedged so that when you "bump" the engine it will unscrew the crank bolt. Don't ever do this cuz it's dangerous, nope dont do that, no, never.....

Hope this helps.

Dec 29, 2010 | 1997 Pontiac Bonneville

2 Answers

I have a dodge magnun and have replaced the front linkage to sway

check the frunt break pads if the pads were ever replaced by aftermarket pads they will make a clunk sound going over bumps

Jul 10, 2010 | 2005 Dodge Magnum

4 Answers

Klunk noise when crossing abrupt road bumps. Replaced shocks; no help. Have check all suspension hinge joints for wear on rubber blocks or loose bolts - nothing loose or broken there.

i think you should look at your tie rodds or more then likly its you rcv joint know to test if it;s that walk to the wheel (make sure the is straight) and give it a good kick if you hear that noise then you need cv joints hope this helps

Sep 21, 2009 | 2005 Pontiac Montana

3 Answers

2006.5 Kia Optima lx, frnt end noise on bumps, ?

You can spray lower control arm points thats attached to the sub frame with penetrating fluid if that does'nt work spray sway bar bushings thats attached to lower control arms.

Mar 18, 2009 | 2006 Kia Optima

2 Answers

Front end shimmy

Track Bar...I replaced mine cuz on the highway over 60mph...after I hit a bump the whole front end shook....tighten it reeeaalllyyy tight

Sep 15, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2003 Toyota Tacoma Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides