Rear Wiper does not move

The part that is attached to the wiper motor is in the wrong location. Remove the nut or bolt that attached the wiper transmission to the motor and remove the short arm from the wiper motor. Turn the wiper motor on and then off. wait until it stops moving. Set the wiper arms to the correct "home" position. Reattach the wiper transmission arm to the wiper motor.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Wiper Motor

1. Remove finish caps.
   
2. Make reference marks for installation and remove wiper arms.
   
3. Remove the air inlet grille panel.
   
4. Remove the bolts attaching the wiper module to the plenum.
   
5. Carefully lift the wiper module out of the plenum.
   
6. Disconnect the electrical connector from the wiper motor.
   
7. Disconnect the clip retaining the electrical harness to the wiper module.
   
8. Remove the wiper module assembly from the vehicle.
   
9. Remove the wiper motor.
   

Wiper module assembly and motor removal
To install:

1. Install wiper motor and mounting bolts, tighten to 40 inch. lbs.(4.5 Nm).
   
2. Connect the electrical connector to the wiper motor.
   
3. Connect the clip retaining the electrical harness to the wiper module.
   
4. Position the wiper module assembly into the plenum.
   
5. Install the fasteners attaching the wiper module assembly to the plenum, tighten fasteners to 89 inch. lbs. (10 Nm).
   
6. Install the air inlet grille panel.
   
7. Install wiper arms and align to reference marks.
   
8. Tighten wiper arm retaining nuts to 26 ft. lbs. (35 Nm).
9. Install finish caps.

https://www.youtube.com/watch?v=dHJli8z1_jI
https://www.youtube.com/watch?v=A3hLLrwz8wQ

It Sounds Like, Either The Arms Are Loose ,If You Can Hear Something Moving Behind The Dash,
Or The Linkages Are Seized ,If The Motor Just Hums No Movement Heard,In Which Case Try Spraying Q 20 On The Linkage And Try Moving The Wiper Arms By Hand To Get It Going Again,
If Not The Motor May Just Be Burn;t Out.

Yes. Immediately in front of your windshield is a panel about 3 or 4 inches wide and that panel, which is the same color as your car, goes from one front fender across to the other one.
That panel, which has many vent holes or louvres in it, also has 2 holes for your wiper arms and blades, where they attach.
That panel will come off, sometimes you have to remove the whole hood of the car to get it off.
(You have to take both wiper arms & blade assembly off first.)
You will then find the linkage from the wiper motor to the driver's wiper arm/blade is disconnected.
(The wiper motor is about the size of your fist, and has a few wires attached to it.)
Probably a plastic bushing has fallen apart on the connecting link.
You will need to get a new or good used connecting link and attach it.

Check to see if wiper arm bushing is bad. remove both wiper arms lift cowl cover to access arms from wiper motor should be able to see if arm is off. replace bushing.

Windshield Wiper Blade & Arm Removal & Installation Front To Remove:

1. Mark the location of the wiper on the windshield.
2. Remove or disconnect the following:
   • Nut cover
   • Nut from the wiper arm
   • Wiper arm

Wiper arm mounting nut
To Install:

1. Install or connect the following:
   • Secure the wiper arm with the nut.
     1. Tighten to: 17 ft-lb (23 Nm)
   • Nut cover

Rear To Remove:

1. Put the wiper arm in the park position.
2. Remove or disconnect the following:
   • The washer hose from the connector
   • The cap from the wiper arm
   • The nut from the wiper arm
   • The wiper arm from the wiper motor shaft

Rear wiper arm mounting nut
To Install:

1. Install or connect the following:
   • The wiper arm on the wiper motor shaft in the park position with the wiper arm resting on the park ramp
   • The nut on the wiper arm
     1. Tighten the nut. Torque to: 17 ft lbs (23 nm)
   • The cap on the wiper arm
   • The washer hose on the connector

---
The wiper motor hopefully is ok, but if the wiper arms were not mounted at the right spot, it could have damaged the motor as it returned to the rest position, unfortunately.

If there is noise, the noise could be coming from the wiper arm joint being stripped out or the motor itself assuming that the ball joints under the hood and behind the firewall are still connected.

Check these items, and I'm sure you will get to the bottom of this.

Good luck on this repair.

The motor could be bad, but it's likely that the ball joint connections under the hood area under the cowl have become disconnected for the one windshield wiper arm.

The connection of the arm that moves should be checked for being at the correct angle for parking.
Removal & Installation 2000-03 Wiper Motor and Bushing Replacement L4-2.2L (Vin F) & V6-3.0L (Vin R) To Remove:

1. Before servicing the vehicle refer to the precautions at the beginning of this section
2. Remove the wiper arm finish caps
3. Mark both wiper arm positions on the windshield by using a wax pencil or tape
4. Remove or disconnect the following:
   • Wiper arm retaining nuts and washers
   • Wiper arms
   • Weather-strip at rear of hood
     
     
     
     
   • Grill nuts from base of wiper arm shaft
   • Grill
   • Electrical harness connector from the wiper motor
   • Wiper motor retaining bolts
   • Wiper motor assembly from plenum area
   
   
   
   
   
5. If replacing wiper module bushings remove the steel bushing first then the rubber grommet
6. Remove the wiper motor from the transmission assembly

To Install:

1. Install or connect the following:
   • Wiper motor to transmission assembly NOTE: If the wiper module bushings were replaced install the rubber grommet first then the steel bushing.
     
   • Wiper motor to plenum area
   • Wiper motor retaining bolts; torque to 44 lb-in. (5 Nm)
   • Electrical harness connector to the wiper motor
   • Weather-strip at the rear of hood
   • Grill
   • Grill nuts to the base of the wiper arm shaft
2. Install the wiper arm assemblies at the marks made during removal or at the PARK position if a new wiper motor is installed
3. Install the wiper arm retaining washers and nuts; torque to 9 lb-ft. (12 Nm)
4. Install the wiper arm finish caps
5. Verify correct wiper system operation

Very common problem, most likely needs a new wiper motor. Cheap fix.

Flip the caps up from bottom of wiper arm to expose where they attach to pivots. There should be a nut holding them on, try snugging that nut up a bit & see what happens. if it helps, remove the nuts, pry the arms off, and clean inside where spline etc., is and re-attach arms in proper(same) spot and tighten nuts again, but be careful not to tighten too much & snap the stud.

This is what I Found there was not any Illustration's with it looks Fairly simple, Good luck



FRONT

1. Disconnect linkage assembly from wiper motor shaft.
2. Disconnect electrical connectors from wiper motor.
3. Remove wiper motor attaching bolts, then wiper motor.

REAR

1. Remove wiper blade and arm assembly.
2. Remove access panel on back door.
3. Disconnect linkage assembly from wiper motor shaft.
4. Disconnect electrical connectors from wiper motor.
5. Remove wiper motor attaching bolts, then wiper motor.

Skill
Level Mfg.
Warranty Standard Wiper Motor Labor Replace Front B 0.7 1.0
PLEASE DONT FORGET TO RATE ME Thank You Much