Question about 2008 GMC Canyon 2WD

1 Answer

Where do i find the evap system on a 2008 gmc canyon

I need to know where to look for the evap system on my engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • GMC Master
  • 808 Answers

The evap system is the vapor control of gasoline in the fuel tank it runs the whole length of the truck involving a vapor canister and vent control valves and purge valves of course hoses also.

Posted on Apr 17, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 375 Answers

SOURCE: ignition coil - 2005 gmc canyon

Just above each spark plug.

Posted on May 18, 2008

eric71079
  • 10 Answers

SOURCE: 2004 GMC truck

MAY BE A VACUME LINE IS NOT HOOKED UP RIGHT

Posted on May 27, 2008

  • 1 Answer

SOURCE: replace passenger side mirror, power

Open the door. Look for a cheap piece of plastic near where the mirror is located. Carefully pry the plastic off. There are 3 bolts. There is a wire harness connector. Unbolt the mirror and unclip the harness. Installation is reverse of removal. Easy job.

Posted on Jun 12, 2009

  • 3 Answers

SOURCE: i need to know where my spark plugs are on my 2005 GMC canyon tru

under black breather cap om top of motor there is one bolt per plug take bolt out slid long black sleve out plug is in head you will need a 6 inch extension to get them out

Posted on Jun 21, 2009

  • 5 Answers

SOURCE: Rear Main Oil Seal leak 2008 GMC Canyon

I think this is for an oil level sensor. Should be easy to change , or a shop can do it for a nominal charge. The dealerships will want more.

Posted on Feb 01, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset the antitheft system on a 2005 gmc canyon it turns but wont stay on what do i need to do an i need to know quick


If the truck has a factory anti-theft system, the system will not allow the engine to crank or start. So if it cranks, you have a different problem.

Aug 05, 2014 | 2005 GMC Canyon

1 Answer

GMC Canyon problem DTC P0449


Code 449 is for a problem with the EVAP system vent valve solenoid circuit.
The solenoid may not be reacting to computer commands to open or close.
The solenoid and circuit would need to be tested.

Feb 19, 2013 | 2005 GMC Canyon

1 Answer

Used a code reader on my 2006 GMC Canyon and it read P0455 can you tell me what this is


EVAP System (Gross Leak ) PO455

Should be easy to find
That is the largest of leak codes

Mar 30, 2011 | GMC Canyon Cars & Trucks

1 Answer

Truck wont crank each time


It sounds to me like that you have several different issues with you vech and on the pass lock system will not cause all the problems listed how ever it will cause the no crank and after five min or 30 min start it is most likely the pass lock sensor unless your truck has a pk3 system (the key will have a + or pk3 stamped on it)If it is a pk3 system then it may be the theft detturent module if ton a pk3 system then most likely a pass lock sensor . Take the vech to some one that can ck for codes and find out all the codes set in the vech. This will tell a whole lot about what is going on with the vech .Im not very good on drivabilty problems. The evap leak and the mis fire will not be related to the pass lock problem.

Jul 10, 2009 | 2006 GMC Canyon

1 Answer

2006 gmc canyon 3.5 inline 5 cyl.


Not much of a vacuum diagram on this vehicle. Uses vacuum mainly for the EVAP system ( not a good source). Best bet would be to use a source that stems directly from the intake manifold. Good luck

Jul 07, 2008 | 2006 GMC Canyon

Not finding what you are looking for?
Cars & Trucks Logo

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...