2011 Chevrolet Chevrolet Cruze LT Logo

Related Topics:

A
Anonymous Posted on Apr 12, 2014
Be the first to answer

Replace rearview mirror

Need to tighten inside rearview mirror. How do you remove plastic cover?

Answer This Question

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Oct 27, 2008

SOURCE: Replace passenger side power mirror clearance lamp (bulb only).

If you are facing the passenger side mirror adjust the top (large) mirror so that it is turning in towards the truck as far as it will go. Then look behind the mirror in the bottom righthand corner (outside bottom corner) and you will see a silver metal clip. Take a straight head screw driver and push on that clip and the lens will pop out. Then you simply unscrew the bulb holder from the lens and replace your bulb. Good luck!

Ad

Anonymous

  • 1118 Answers
  • Posted on Apr 19, 2009

SOURCE: need to replace mirror-glue failed- can't remove the button from mirror. help!

There is a small hole wear you insert a allen wrench or allen key to loosen a set screw to get the button out.

Anonymous

  • 314 Answers
  • Posted on Jun 11, 2009

SOURCE: 1999 gmc jimmy rearview mirror diagram needed

It should just slide out. You might have to use a little bit of force

c17hydro

Greg Bernett

  • 2993 Answers
  • Posted on Jun 30, 2009

SOURCE: license plate bulbs on 98 Park Avenue

License Plate Lights Removal & Installation 1997 – 2000 To Remove:

License/backup Lamp Assembly


76707d9.gif

  1. Remove the rear compartment lid trim. (if necessary)
  2. Disconnect the license/backup assembly connector from the body harness.
  3. While removing the license/backup lamp assembly from the rear compartment lid, disconnect the harness grommet from the rear compartment lid.
  4. Remove the license lamp housing from the license/backup lamp assembly.
  5. Remove the license lamp bulb from the housing and socket.
To Install:
  1. Install the license lamp bulb into the socket and housing.
  2. Install the license lamp housing onto the license/backup lamp assembly
    • Torque the fastener to 18 in-lb (2 Nm).
  3. While holding the license/backup lamp assembly, install the harness grommet to the rear compartment lid.
  4. Install the license/backup lamp assembly
    • Torque the fasteners to 53 in-lb (6 Nm).
  5. Connect the license/backup assembly connector to the body harness.
  6. Install the rear compartment lid trim. (if necessary)

Anonymous

  • 119 Answers
  • Posted on Jul 19, 2009

SOURCE: replace passenger mirror 1999 subaru outback

you need to remove door panel to unplug miroor connection

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Replace broken glass volvo s80 side rearview mirror
Once you pop off the plastic cover on the mirror (that matches your car color) everything is accessible.
Read full answer
Feb 14, 2015 • 2002 Volvo S80
0helpful
1answer

I have a 2000 VW Jetta and my interior windshielp rearview mirror's auto dimming melted down inside of my mirror and I need to replace it. I need to know if I am able to put a normal rear view mir
yes any vw mirror will work.
Read full answer
Aug 03, 2012 • Cars & Trucks
0helpful
1answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.
Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif
Read full answer
Jan 14, 2011 • 1999 Ford Taurus
0helpful
1answer

The interior rear view mirror has temperature and compass displays, but only work for a short time at start- up.I have tried unplugging the harness on the back of the mirror and cleaning contacts. It`s...
Temperature Display
The inside rearview mirror supplies a 5 volt signal circuit and low reference circuit to the ambient air temperature sensor. The inside rearview mirror monitors and records the voltage on the signal circuit of the ambient air temperature sensor. The inside rearview mirror uses this recorded voltage to display the temperature on the temperature display portion of the compass/temperature display. The temperature display will show "ICE" when the ignition is first turned on and the current temperature is 3°C (37°F) or below. The display will toggle between "ICE" and the actual outside temperature for approximately 4 minutes.
The mirror will display "OC" if the mirror senses a temperature of less than -40°C (-40°F).
the mirror will display a "SC" if the mirror senses a temperature of greater than 112°C (143°F).



Replace the inside rearview mirror with compass. Refer to Inside Rearview Mirror Replacement .
Read full answer
Nov 14, 2017 • 2001 Chevrolet Suburban
1helpful
1answer

Cracked mirror only, mounting and other parts are functioning well. Can I purchase a mirror only and if so, where?? This is for 2006 Pontiac Grand Prix and the passenger side mirror is cracked but works...
Hello, yes the glass can be replaced. you will need to see your local GM dealer for the glass. real simple to replace.





  • Carefully push the outside rearview mirror face on the inner edge, near the front door window glass, to allow access.
  • Insert a large flat-bladed screwdriver in the slot between mirror lens and the mounting base.
  • Grasp the mirror face firmly and pull it from the mirror body.
  • Remove the outside rearview mirror case from the outside rearview mirror housing and disconnect the heater wire, if equipped.






  • Using the palm of your gloved hand, press firmly on the center of the glass until the case seats onto the motor.
    • The mirror will make a snapping noise when properly seated.
  • Inspect the mirror for proper operation.


    • cf49034.gif

    f845709.gif
    Read full answer
    Jul 03, 2010 • 2006 Pontiac Grand Prix
    1helpful
    1answer

    How to replace rearview mirrors on yukon 1996
    The replacement of outside rearview mirrors is straight-forward and can be done in an hour or so. If you need new power mirrors, first shop with local body parts suppliers in your area. The after-market mirrors are nearly identical and can be purchased for about $20-$30 per side. Remove the plastic triangular cover over the inside of the mirror by lifting up at base and then release clip at the top which is an upward motion off of a slot in the rear of the triangle. Then pull out the foam insulation carefully. The 3 nuts are 10mm and a long scket works best. For the one at the very front, you will have to use an open end wrench to loosen the nut. There is not much room for a socket. Be carefull to not drop the nuts down the inside of the door, because you don't want to remove the door panel and then the inner metal panel to get them out. If you lose them, buy new ones or replace with proper treaded ones in your garage. After the three nuts are off you need to disconect the wiring. Stop here and make sure you have enough slack in the wiring to be able to hold the female end securely, while you refit your new mirror. I took a piece of wire an dwrapped it around the female end to keep it within reach to re-attach the wiring after the nuts are tightened. Then just replace your foam insulation, and install the triangular cover and you're all set.
    Read full answer
    Nov 30, 2009 • 1996 GMC Yukon
    0helpful
    1answer

    Rear view mirror needs tightening
    go to a workshop
    Read full answer
    Jul 17, 2009 • 2004 Hyundai Santa Fe
    0helpful
    1answer

    Kia sorento 55 plate wing mirror
    1. Disconnect the negative battery cable.
    2. Remove the outside rearview mirror garnish.
    3. Disconnect the harness connector.
    4. Remove the 3 bolts and the outside mirror.
    To install:
    1. Install the outside mirror and tighten the bolts to 60 inch lbs. (7 Nm).
    2. Connect the wiring harness.
    3. Install the mirror garnish.
    4. Connect the negative battery cable
    Read full answer
    Jan 31, 2009 • 2005 Kia Sorento
    1helpful
    2answers

    Rearview Mirror looseness
    Note: You may want to remove the mirror from the windshield first to make the following steps easier. It's not necessary, but it's up to you. If so, pry off the plastic cover at the top of the mirror stalk, disconnect the power cord, and then pull the mirror downwards and parallel to the windshield to remove it.

    Method 1: On the back side of the mirror below the ball joint, there is a small round cover. Insert a sharp blade tip at the top of the cover and carefully pry it out. Underneath is the tip of the tension screw. It has a slot in the end of it that can be tightened with a small flat-blade screwdriver. Carefully replace the cover, inserting the bottom tab first, then snap in the top. If the mirror is still not tight enough, go to Method 2.

    Method 2: Carefully pry off the rim bezel of the mirror, starting in the middle of the seam on the bottom, working your way around the edge. The bezel will pop off when you get past one of the ends. I used a pair of heavy guitar picks to keep the latches from snapping back into place as I progressed. Once the bezel falls off, the mirror assembly will dangle from the power cord. The Phillips tension screw is in the center bottom of the case; tighten it to suit, and make certain that the four bracket mounting screws around it are all tight, too. Then place the mirror assembly back in place and snap the bezel back into place, starting at the top.
    Read full answer
    Sep 10, 2008 • Hyundai Motor 2003 XG350
    0helpful
    1answer

    Custom Rear view mirror
    Hiya...ALL factory-installed rearview mirrors are installed with different wires due to options.
    About 6 different rearview mirrors are installed with those options such as On-Star, light, compass, and those features which use different wires....THIS CANNOT be modified with different rearview mirror....**for example, the Equinox owner attempt to pull out a factory-installed base rearview mirror and put in different one that has compass/temperature built into the rearview mirror**

    However, the wires are located inside the front headliner which requires removing the sunvisor (and possible removal of interior plastic trim part at the left/right ends of the windshield) prior to pull the headliner down, and a small metal philips or torx screw is used to secure the rearview mirror onto the bracket glued to the windshield.

    The best solution is to leave the original factory-installed rearview mirror in place.
    Read full answer
    May 16, 2008 • 2006 Chevrolet Equinox
    Not finding what you are looking for?

    View Most Popular

    2011 Chevrolet Cruze LT

    • Cars & Trucks

    Related Question

    Replace broken glass volvo s80 side rearview mirror

    • 2002 Volvo S80

    74 views

    Ask a Question

    Usually answered in minutes!

    Popular Questions

    4.3 Firing order diagram for 4.3L v6 Chevy engine

    1999 Chevrolet K1500

    What does my check engine light trouble code $7e8 mean?

    2009 Chevrolet HHR 2.4

    Transmission slips after engine warms up

    Chevrolet Cavalier Cars & Trucks

    When i press the ac button it blinks three times

    2007 Chevrolet Tahoe

    What causes high pressure in cooling system?

    1993 Chevrolet Suburban

    Check Out the Latest Top Trucks Report!
    Check Out the Latest Top Trucks Report!

    View all Fixya Reports

    Top Chevrolet Experts

    ZJ Limited
    ZJ Limited

    Level 3 Expert

    17989 Answers

    john h

    Level 3 Expert

    29494 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    15088 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    PDF Manual
    2011_chevrolet_cruze_owners.pdf....

    2011 Chevrolet Cruze...

    Loading...