Why is this vehicle not under recall

Lower you can do fairly easy. Upper, a bit tougher.For the upper you will need a spring compressor.

if this has a conventional front end(not front wheel drive) then there will be one on each outer tie rod end one on each inner tie rod end, both upper and lower ball joints on each side, idler arm and pitman arm. if its front wheel drive it will have a rack and pinion steering. there for there will be one on each outer tie rod end and one on each lower ball joint, if they have grease fittings. so conventional steering has 10 fittings total and rack and pinion has 4 total.

1. Before servicing the vehicle, refer to the Precautions section.
   
2. Remove or disconnect the following:
   
   • Front wheel
     
   • Spindle nut
     
   • Wheel speed sensor, if equipped
     
   • Outer tie rod end
     
   • Stabilizer bar link
     
   • Lower ball joint
     
3. Press the stub shaft out of the hub.
   
4. Pry the inner joint out of the transaxle or intermediate shaft.
   

To install:

NOTE

Use new circlips, split pins and self-locking nuts for assembly.

1. Install the inner joint so that the circlip is felt to seat in the retaining groove.
   
2. Guide the stub shaft into the hub.
   
3. Install or connect the following:
   
   • Lower ball joint and torque the nut to 43-52 ft. lbs. (58-70 Nm)
     
   • Stabilizer bar link
     
   • Outer tie rod end and torque the nut to 17-25 ft. lbs. (23-34 Nm)
     
   • Wheel speed sensor, if equipped
     
   • Spindle nut and torque the nut to 144-187 ft. lbs. (195-253 Nm)
     
   • Front wheel
     
4. Check and/or adjust the wheel alignment.
   

Wheel Spindle, F-150, F-250, F-350
Removal

1. Raise the front of the vehicle and install safety stands.
   

1. Remove the wheel and tire assembly. Refer to Section 04-04 .
   

1. Remove the disc brake caliper (2B120) from the rotor and wire it out of the way. Refer to Section 06-03 .
   

1. Remove the dust cap, cotter pin, nut retainer, nut, washer and front wheel bearing (1216).
   

1. Remove the rotor from the front wheel spindle (3105).
   
   
   
   
   
   Item Part Number Description 1 606085 Clamp Bolt 2 3B404 Camber Adjuster 3 800895 Nut 4 800937 Nut 5 3049 Front Suspension Upper Ball Joint 6 3050 Front Suspension Lower Arm Ball Joint 7 3105 Front Wheel Spindle 8 642569 Cotter Pin 9 3304 Steering Sector Shaft Arm Drag Link 10 383489 Nut 11 3001 Front Axle Assembly 12 388727 Bolt A - Tighten to 77-103 Nm
   (57-75 Lb-Ft) B - Tighten to 68-92 Nm
   (50-67 Lb-Ft) C - Tighten to 113-153 Nm (83-112 Lb-Ft) D - Tighten to 340-460 Nm (250-339 Lb-Ft)

1. Remove bearing cone and roller (1201) and wheel hub grease seal (1190). Discard the seal.
   

1. Remove front disc brake rotor shield (2K004). Refer to Section 06-03 .
   

1. Disconnect the steering linkage from the integral front wheel spindle and spindle arm by removing the cotter pin and nut and then removing the front wheel spindle tie rod from the spindle arm with Tie Rod End Remover TOOL-3290-D or equivalent.
   

1. Remove the cotter pin and castellated nut from the lower ball joint stud.
   

1. Remove the nut from the axle clamp bolt and remove the bolt from the axle.
   

1. Remove the camber adjuster from the upper ball joint stud and axle beam. If required, use Ball Joint Removing Tool D81T-3010-B or equivalent to remove adjuster.
   

1. CAUTION: Do not use a pickle fork to separate the ball joint from the axle as this will damage the seal and the ball joint socket.
   Strike the inside area of the axle as shown to pop lower ball joints loose from the axle beam.
   

1. Remove the front wheel spindle and ball joint from the axle.
   
   

Ball Joint, F-150, F-250, F-350 SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number U-Joint Tool T74P-4635-C Ball Joint Remover T94T-3010-AH
Removal

1. Remove the front wheel spindle (3105) and ball joint assembly from the axle. Refer to Wheel Spindle, F-150, F-250, F-350 in the Removal and Installation portion of this section.
   

1. NOTE: Lower ball joint must be removed first.
   
   Install the front wheel spindle in a vise and remove the snap ring from the lower ball joint.
   

1. Remove the lower ball joint from the front wheel spindle using U-Joint Tool T74P-4635-C and Receiver Cup D81T-3010-A5 or equivalent for F-150. Use Ball Joint Remover T94T-3010-AH for F-250 and F-350.
   

1. Turn the forcing screw clockwise until the ball joint is removed from the front wheel spindle.
   
2. CAUTION: Do not heat the ball joint or the front wheel spindle to aid in removal.
   Assemble U-joint tool and cup on the upper ball joint, and turn forcing screw clockwise until ball joint is removed from the front wheel spindle.
   
   
   Installation
   
   1. CAUTION: Do not heat the ball joint or axle to aid in installation.
      NOTE: Upper ball joint must be installed into the front wheel spindle first.
      
      NOTE: Individual ball joint tools are included in Ball Joint Adapter Set D81T-3010-A or equivalent.
      
      To install the upper ball joint, assemble C-frame assembly, Ball Joint Receiver Cup D81T-3010-A5 and Installation Cup D81T-3010-A1 and D81T-3010-A3 or equivalents inside cup D81T-3010-A4 or equivalent in position on the front wheel spindle.
      
   1. Turn forcing screw clockwise until ball joint is seated.
      
      
      
      
   

General Description
The front suspension allows each wheel to compensate for changes in the road surface without affecting the opposite wheel. Each wheel independently connects to the frame with a steering knuckle, ball joint assemblies, and upper and lower control arms.
The control arms specifically allow the steering knuckles to move in a three-dimensional arc. Two tie rods connect to steering arms on the knuckles and an intermediate rod. These operate the front wheels.
The two-wheel drive vehicles have coil chassis springs. These springs are mounted between the spring housings on the frame and the lower control arms. Double, direct acting shock absorbers are inside the coil springs. The coil springs attach to the lower control arms and offer ride control.
The upper part of each shock absorber extends through the upper control arm frame bracket. This bracket has two grommets, two grommet retainers, and a nut.
A spring stabilizer shaft controls the side roll of the front suspension. This shaft is mounted in rubber bushings that are held by brackets to the frame side rails. The ends of the stabilizer shaft connect to the lower control arms with link bolts. Rubber grommets isolate these link bolts. Rubber bushings attach the upper control arm to a cross shaft. Frame brackets bolt the cross shaft.
A ball joint assembly is riveted to the outer end of the upper control arm. A rubber spring in the control arm assures that the ball seats properly in the socket. A castellated nut and a cotter pin join the steering knuckle to the upper ball joint.
The inner ends of the lower control arm have pressed-in bushings. The bolts pass through the bushings and join the arm to the frame. The lower ball joint assembly is a press fit in the lower control arm and attaches to the steering knuckle with a castellated nut and a cotter pin.
Ball socket assemblies have rubber grease seals. These seals prevent entry of moisture and dirt and damage to the bearing surfaces.
Four-wheel drive models have a front suspension that consists of the control arms, a stabilizer bar, a shock absorber, and right and left torsion bars. The torsion bars replace the conventional coil springs. The lower control arm attaches to the front end of the torsion bar. The rear end of the torsion bar mounts on an adjustable arm at the crossmember. This arm adjustment controls the vehicle trim height.
Two-wheel drive vehicles have tapered roller sheel bearings. These bearings are adjustible and need lubrication.
Four-wheel drive models and RWD Utilities have sealed front-wheel bearings. These bearings are pre-adjusted and need no lubrication.
Heat treatment may create darkened areas on the bearing assembly. This discoloration does not signal a need for replacement.
Hope this helps?

replace the entire CV axles. Support vehicle with jackstands by frame. Remove front wheels. Remove axle nuts. Remove lower balljoint nut. Separate balljoint from nuckle by banging hard with ball peen hammer on knuckle on spindle assy. Remove outer tie-rod nut. Separate tie-rod from steering nuckle by bangin on nuckle with ball-peen hammer. Use long pry bar to hold lower control arm down while simultaneously pulling hub/spindle assembly away from vehicle and pushing axle through hub toward transaxle. Go under vehicle and pry inner cv joint away from transaxle while holding axle assembly.
Install new CV axle in reverse of the disassembly.

Removal & Installation NOTE This procedure requires the use of the following special tools: J 9519-E Lower Ball Joint Remover and Installer, J 34874 Booster Seal Remover/Installer, J 41435 Ball Joint Installer, J 45105-1 Ball Joint Flaring Adapter and J 45105-2 Receiver.

1. On 4WD vehicles, remove the wheel center cap and drive axle nut.
   
2. Raise and support the vehicle.
   
3. Remove or disconnect the following:
   
   • Tire and wheel
     
   • Wheel hub and bearing, if necessary
     
   • Outer tie rod retaining nut
     
   • Out tie rod from the steering knuckle using a suitable puller
     
   • Brake hose bracket retaining bolts and bracket
     
   • Upper control arm-to-steering knuckle pinch bolt and nut
     
   • Upper control arm from the steering knuckle
     
   • Lower ball joint retaining nut
     
   • Steering knuckle from the lower control arm using a suitable ball joint removal tool
     
   • Steering knuckle from the vehicle
     
   • Lower ball joint flange with a chisel
     
4. Install tools J 9519-E and J 34874 to the lower ball joint, then use those tools to remove the lower ball joint from the lower control arm.
   

To install:

1. Install or connect the following:
   
   • Lower ball joint to the lower control arm, using tools J 9519-E, J 41435 and J 45105-2
     
2. Remove the tools from the lower control arm.
   
   • Tools J 9519-E and J 45105-1 to the lower ball joint
     
3. Flare the lower ball joint flange with J 9519-E and J 45105-1, then remove the tools from the lower ball joint.
   
   • Steering knuckle to the lower control arm
     
   • Lower ball joint retaining nut and tighten to 81 ft. lbs. (110 Nm)
     
   • Upper control arm to the steering knuckle
     
   • Upper control arm pinch bolt and nut and tighten to 30 ft. lbs. (41 Nm)
     
   • Brake hose bracket to the steering knuckle
     
   • Brake hose bracket retaining nuts and tighten to 7 ft. lbs. (10 Nm)
     
   • Outer tie rod to the steering knuckle
     
   • Outer tie rod retaining nut and tighten to 33 ft. lbs. (45 Nm)
     
   • Wheel hub and bearing, if removed
     
   • Tire and wheel
     
4. Lower the vehicle
   
   • Drive axle nut, if 4WD, and tighten to 103 ft. lbs. (140 Nm)
     
   • Wheel center cap, if removed
     
5. Check the front wheel alignment.
   

support vehicle under A frame remove wheel. loosen nut on top of ball joint.seperate spindle assembly from ball joint w/ball joint seperating tool AKA pickle fork.remove nut.ball joint is riveted to lower A frame-chisel off or drill out rivets.install new ball joint w/nuts &bolts supplied with it

That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

cv joint