1996 Geo Prizm Logo

Related Topics:

A
Anonymous Posted on Apr 06, 2014

Box fuse picture

My car wont start because the alarm is engaged and cant find any switch for days. need to remove fuse and cut red wire but dont know what fuse to pull

1 Answer

_-__-___-_

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Geo Master 20,706 Answers
  • Posted on Oct 23, 2016
_-__-___-_
Geo Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Apr 06, 2013
Answers
20706
Questions
2
Helped
6804181
Points
57965

Old post, and I feel your pain or others land here.
yes, The IMMO(alarm) on the car can kill the engine dead
some cut fuel, others cut cranking.
The 96 prizm/corolla. is what it is.
early cars were (daffy) and easy to hack ,done most.
if the immo lamp stick on what to do. lacking new alarm programming or repairs to same. how to HACK.
hack IMMO 101:
the answer can very by make of car and year, newer cars are impossible.
do not confuse words writting about 1991 car , on a 96
they are worlds apart(evolution, and LAWS)
your alarm box is called.
doors and locks and theft deterrent.
as expected its got a zillion pins, (big job it has)
but only 1 pin matters, (hacking mind set) pin A1 SRLY
im no genius, im just and electronics tech, retire. and can read this print , here at mitchells so can you.
the print shows that pin as P, my guess for Purple wire.
next is the starter pages.
it shows, what? it goes to the starter relay coil
and the non alarm car wire ground there is missing
so there is your fix, ground the purple wire there
or at pin 2 of relay start, ground that.
now the starter cranks forever, no matter what , deity willing.

The AM1 fuse kills the live relay power.
or pull battery neg lug, and all is off line, 0volts.
The GIG+DOME+HORN fuse kills dead the alarm box
or
pull the AM2 or the power fuel.
so will the 100 amp ALT fuse.

all this in the book , the schematic, all that.
just ground the P wire. end story

watch out for door locks, keep windows open , killing this alarm box. as it runs all door lock motor......... !!!

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Wires has been cut under dash of a 1997 ford escort need help rewiring so car will run

HOW CAN THE WIRE BEEN CUT,
DO YOU HAVE TILT WHEEL, REMOVE STEERING COVER OD THE IGNITION STEERING AREA, LOOK AT THE WIRES, DO THEY LOOK LIKE SOME ONE CUT THEM OR THEY CHANGE COLORS DO TO A ALARM SYSTEM, IF THEY CHANGE COLOR, COULD BE THE AFTER MARKET ALARM RELAY THAT WONT ALLOWED YOU TO START, IF YOU DO NOT KNOW WERE IT IS, IS OK, OPEN THE CONNECTION AND REMOVE THE WIRE COMING FROM ALARM TO IGNITION SWITCH WIRE, FIND THE OTHER END OF THE IGNITION WIRE THAT WAS CUT OUT , SEPARATE FROM THE OTHER WIRE ALSO FROM THE ALARM, AND RECONNECT BOTH IDENTICAL COLOR WIRE TOGETHER AND IT WELL START, UNLESS YOU HAVE A SECURITY LIGHT ON THE DASH, CHECK THIS OUT FIRST., PROGRAMING MAY BE NEED IT OR OTHER PROBLEMS ARE THERE.
1helpful
1answer

Dont know how to shut alarm off after opening doors and it wont let you start the car how do you cut alarm off to start car

You cant its that simple ,try the spare key in case your key has been in your bag next to a mobile phone which will wipe the chip in the key ,if that doesnt work call the dealer
0helpful
1answer

I'm trying to remove my 02 lancer ls car alarm. I've removed the box and all the wires that was connected to the box but my car still will not start. I've even replaced the starter and it still won't...

The alarm had a wire to not let the car turnover/crank, is that what you mean, or the car turnsover/cranks, but wont run. If it wont turnover, usually its a larger wire that was cut and the alarm wired in, you will need to get this wire reconnected again. I dont have a diagram here to tell you the wire color, but usually its a 10-12 gauge wire. So if you have a 2 wires the same color, and its cut, connect them back again.
3helpful
2answers

Looking for fuse to disable toyota corolla alarm,please help!!

Remove fuse labelled "dome" on engine compartment fuse box. unfortunately this also isolates the radio. I have found when re connecting battery alarm goes off. remove "dome" fuse and then replace it. all ok then.
2helpful
1answer

1994 Camry wont turn or do anything for that matter

Hello,
The red wire is the starter wire, this is the main wire that connects to your starter switch to tell the relay to turn over that starts your car, the other wires are the ingnition wires, these wires is what allows the vehicle to turn on (lights, radio, engine,)
What it sounds like he did when he removed the alarm module was disconnect the power wire that supplys the starter switch.
Try tracing the wire back to where it is connected and see if there is any wire cut the same way as the other end.
try connecting a a remote starter switch from the battery directly to the starter solenoid. this will allow you to see if the wiring inside the car is disconnected or if it is the starter.
0helpful
2answers

I have a 1996 Toyota Tercel with an aftermarket alarm system that I'm uninstalling. There are two large gauge wires from the ignition bundle, black/yellow & white/red that have taps on them. A third...

something is obviously wrong with the wiring try reinstalling the old system and letting a n experienced mechanic install this other one for you wiring is everything
3helpful
2answers

My car alarm is blinking but the remote doesn't work. I already replaced the battery to the remote so I know that's not the problem. If I open the car the alarm goes off and doesn't allow me to start the...

You need to first look under the drivers side dash area near the hood release/fuse panel area and see if there is a valet switch. The switch will look like a little toggle or a push switch. After you locate it, turn the ignition switch to the on position(dont start it) and flick the valet to the opposite position it is in now. If done correctly in most cases the red system light will stay a constant instead of off or blinking indicating you are in valet mode. Next try to start the engine. If this doesnt work you need to remove the alarm system and repair the ignition switch wiring or replace the electrical portion of the ignition switch. The aftermarket alarm cuts into the ignition switch wires and bypasses the start circuit through the alarm module. When disarmed the alarm completes the circuit and allows the car to start. Good luck hope this helps and please rate this.
0helpful
1answer

96 getta trek alarm

the alarm is set right behind the headlight switch within the dash. Pull out the light switch and unplug it. The tricky part here is u most probably have to get ur arm way up inthe from under the steering column. To know with box is the alarm, u can actually hear and feel it clicking. Its roughly the same size as a deck of cards. Once u remove it, cut the 2 big red wires and connect them together. U must connect them in order to bypass the alarm. Good luck.
1helpful
2answers

Bought car and wont start due to alarm. don't know how to override?

say i have a problem were my car alarms is activated and my car wont start unless i push it...i need to disconnect the alarm...HElP
Not finding what you are looking for?

144 views

Ask a Question

Usually answered in minutes!

Top Geo Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...