Question about 1996 Subaru Legacy

2 Answers

Front axles on a 1996 subaru legacy

How do change them

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 167 Answers

Mark the camber bolt on the hub to strut assy just in case you do remove it.......just a precaution

Posted on Jun 26, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 520 Answers

Remove wheel > remove lower control arm bolt > revmove large hub axle nut (160 ft/lbs)>remove,drive out roll pin at tramsmission doj joint with hammer and pin punch and remove doj off transmission spline shaft>drive out axle from hub ensuring not to damage threads...presto

Posted on Jun 26, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Rebgagnon
  • 382 Answers

SOURCE: replacing the front axle on a 93 subaru legacy

When I replace the axle halves, I run the Nut off till it is level with the shaft end. THen take a piece of wood and set it across the shaft and hit the wood with a hammer. Usually only takes one or two hits and pops right out.Then I remove the nut and finish removal . Hope this helps, Good luck and have a great day.

Posted on Mar 04, 2009

Molson02536
  • 3854 Answers

SOURCE: diff ratio on the back axle on a subaru legacy

Look for the option code sticker in the glove box and look up the codes on the net or call the subaru dealer and ask them what the opton codes are on your lagacy. Good luck.

Posted on Apr 06, 2009

  • 1071 Answers

SOURCE: how to remove front axle of a 1991 subaru legacy

there is a roll pin which holds axle to trans remove this but be sure to put new axle in so you can see throught hole where pin goes it is not centered so axle can only go in one way or pin wont go back in

Posted on Jul 21, 2009

youredone82
  • 426 Answers

SOURCE: whats the bolt size on the front hub drive axle on

should eb a 30.mm or a 32.mm

Posted on Sep 28, 2009

  • 333 Answers

SOURCE: 1996 Subaru Legacy

four wheel drive

Posted on May 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 COROLLA VE BLINKING CHECK ENGINE LIGHT


Why did you change anything at all? Makes no sense,
as you found out

Should be studying OBD2 Systems on the internet

Where are the codes you got--- so we can weigh in?

Nov 27, 2012 | 2000 Toyota Corolla

1 Answer

How to do a tune-up for my vehicle by myself


- Change the oil
- Change the spark plugs
- Change the spark plug wires
- Change the cap & rotor or the coils
- Check the timing
- Lube the chassis
- Inspect all fluids
- Change the fuel filter
- Change the air filter

Jan 13, 2011 | 2004 Chevrolet Malibu Maxx

1 Answer

How much oil should i put in at an oil change on a 2001 monte carlo 3.4


Hello, this is the oil capacity of your vehicle.

I hope this info is helpfull

  • with filter change
4.1 liters
4.3 quarts
  • without filter change
3.75 liters
4.0 quarts

  • 3.4L (LA1)
  • with filter change
4.1 liters
4.3 quarts
  • without filter change
3.75 liters
4.0 quarts

  • 3.4L (LA1)
  • with filter change
4.1 liters
4.3 quarts
  • without filter change
3.75 liters
4.0 quarts

  • 3.4L (LA1)
  • with filter change
4.1 liters
4.3 quarts
  • without filter change
3.75 liters
4.0 quarts
  • 3.4L (LA1)
  • with filter change
4.1 liters
4.3 quarts
  • without filter change
3.75 liters
4.0 quarts
  • with filter change
4.1 liters
4.3 quarts
  • without filter change
3.75 liters
4.0 quarts
with filter 4.3 quarts

without oil filter 4 quarts

Oct 08, 2010 | Chevrolet Chevy Cars & Trucks

2 Answers

Two repair shop opinions on changing transmission fluid.


When the colour of the fluid changes it's an indicator of old fluid which must be changed. Too many garages rely on diagnostic codes these days instead of using their brains. The same rule applies to power steering fluid as well.
In any case, a fluid change costs peanuts in comparison to the potential problems which can occur when using fluid which is life-expired. If in doubt, change it.

Apr 01, 2010 | 1998 Volvo S70

1 Answer

Peugeot Expert Van Cambelt change


Most cam belts need to be changed every 60,000 miles. I would change again somewhere around 126,000.

Oct 28, 2009 | 1991 Peugeot 405

3 Answers

Automatic gearbox takes a long time before it will change gears


Have you serviced your transmission latley ? like filter and fluid change ? just a thought .. first thing I would do . then go from there. Jerry

Apr 27, 2009 | 1994 Toyota Land Cruiser

1 Answer

Clutch change


hi it seems your clutch is losing pressure,it works like a shock, known as a hydrolic clutch, i recommend you change it asap.

Feb 05, 2009 | 2000 Volkswagen Beetle

Not finding what you are looking for?
1996 Subaru Legacy Logo

416 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...