P0735 code error code P0735

https://www.rangerovers.net/forum/6-range-rover-mark-iii-l322/239242-2009-hse-range-rover-transmission-fault-p0730.html
https://www.rangerovers.net/forum/9-range-rover-sport-l320/267530-transmission-service-p0735.html
https://www.rangerovers.net/forum/9-range-rover-sport-l320/48932-range-rover-sport-2012-transmission-issue.html
https://www.yourmechanic.com/article/p0746-obd-ii-trouble-code-pressure-control-solenoid-performance-or-stuck-off-by-valerie-johnston

Possible causes of OBD code P0730
- Low transmission fluid level - Dirty transmission fluid - Shift solenoids - Shift solenoids harness or connectors - Transmission mechanical problems - Transmission hydraulic control circuit The Error code is generally activated on detection of the following conditions: The TCM has detected that the transmission is trying to mechanically shift to a lower gear than intended

Possible causes of OBD code P0735
- Low transmission fluid level - Dirty transmission fluid - Shift solenoids - Transmission mechanical problems - Transmission hydraulic control circuit The Error code is generally activated on detection of the following conditions: P0735 is detected when A/T cannot be shifted to the 5th gear position even if electrical circuit is good.

code p0735 refers to gear 5 --incorrect ratio.===causes --wiring---TR sensor / switch---shift solenoids--transmission mechanical fault. I would be replacing the TR sensor/ switch first. IF it looks like a transmission mechanical fault Have pressure test done first and check the bands and clutch adjustments before considering a replacement/ over haul. I feel confident it is a electronic fault

I would say you are looking at a transmission rebuild here.

P0735 FORD - Automatic Transmission Incorrect Fifth Gear Ratio Incorrect Possible causes - Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit
P0732 FORD - Automatic Transmission Incorrect Second Gear Ratio Incorrect All - causes would be the same as above with ALSO Probable bad valve body - and or pressure solenoids. Probable bad clutch band. If the fluid is ok and if you have tried changing the fluid and filter to no aval. Is it time to think about a transmission repair at a local transmission shop. Sorry.

Hi,
For the Audi A8 code P0735 "Gear 5 Ratio incorrect" is a transmission problem and should be taken to a transmission shop that you trust. Have a good day.

This is what your codes mean:

Trouble Code-P0734 (A/T Additional Gear Ratio Error In Fourth Gear)

Trouble Code Conditions:
Vehicle driven to a speed of 4-37 mph at more than 500 rpm, gear selector in 4th Gear in Drive, and the PCM detected too much difference in the engine speed and output shaft speed.

Possible Causes:

• Customer may complain of intermittent 4th gear operation
  
• O/D and 2/4 pressures less than 75 psi
  
• O/D or 2/4 clutch volume indexes out of specification
  
• O/D accumulator seals are damaged
  
• Transmission enters "limp in" mode running in 4th gear
  

Trouble Code-P0735 (A/T Gear Ratio Error Fourth Prime)

Trouble Code Conditions:
Vehicle driven any forward Gear, and the TCM detected the ratio of the Input speed to the Output Speed did not match the current Gear Ratio (this test can take up to 5 minutes).

Possible Causes:

• Related Gear Ratio trouble codes may be stored (note that some of these Gear Ratio trouble codes may be intermittent)
  
• Transmission has internal problems or damage present
  

You have a transmission problem.

P0735- 5th gear ratio invalid, means there is a mechanical problem on the transmission

p0732
incorrect gear ratio,second gear

p0735
incorrect gear ratio, fifth gear

p1762
are you sure this is the code number it is a manufacturer-specific code. and i'm not seeing it in my bood check to see if you have the right numbers on it.

AAmco