HOW TO REMOVE HEATER BLOWER MOTOR 1992 CHEVROLET PICKUP

It is located right next to the blower motor.

By heater motor if you mean blower motor for the heater system, it is located at the right rear of the engine compartment, under the hood. You will need to possibly cut the rubber barrier around the motor (the round part that sticks out) to access the (5) 7mm bolts. You will probably need to remove the ECM (Engine Control Module) and bracket to completely remove. If you are having issues with the blower motor fan not working I would suspect the blower resistor assembly or the 6 wire connector going to it, before condemning the blower motor. If you mean the heater core by saying heater motor, then it is directly located beside the blower motor and is a lot more difficult to remove. The heater case will need to be separated, and there are hidden bolts located on the inside of the trucks cab.

Heater Core - REMOVAL & INSTALLATION
1991-92 R/V and 1991-98 C/K Series

1. Disconnect the negative battery cable.
2. Drain the cooling system.
3. Remove the instrument panel glove compartment.
4. Tag and unplug all electrical leads as necessary.
5. Remove the center air distribution duct from the floor.
6. If necessary, remove the ECM and mounting tray.
7. Remove the hinge pillar trim panels.
8. Remove the blower motor cover and then remove the motor.
9. Remove the steering wheel and tilt back the instrument panel slightly.
10. Remove the coolant overflow tank. Disengage the heater hoses at the core connections.
11. Unfasten the attaching screws and nut and then remove the heater case.
12. Remove the seven screws and lift off the heater case cover.
13. Remove the fasteners and brackets that hold the heater core to the case and lift the core from the case.

To install:

1. Install the heater core in the case.
2. Install the heater case bottom plate. Make sure there is a good seal.
3. Install the heater case into the truck. Tighten the 4 lower screws to 17 inch lbs. (2 Nm); the upper screw to 97 inch lbs. (11 Nm); and the nuts to 25 inch lbs. (2.8 Nm).
4. Connect the heater hoses at the core tubes.
5. Install the coolant overflow tank.
6. Install the instrument panel and the steering wheel.
7. Install the blower motor and cover.
8. Install the trim panels and if removed, the ECM. Install the air distribution duct and reconnect all electrical leads.
9. Install the glove compartment. Fill the cooling system and connect the battery cable.

Blower Motor - REMOVAL & INSTALLATION
1992-98 Models
(see Figure 4)

1. Disconnect the negative battery cable.
2. Remove the right rear quarter panel trim.
3. Disconnect the electrical lead at the fan.
4. Remove the screws and if equipped, the cooling tube.
5. If necessary, remove the fan retaining nut and lift out the blower fan.
6. Remove the blower motor.
   

To install:

1. Install the blower motor and then position the fan.
2. Install the retaining nut and then tighten the mounting screws to 12 inch lbs. (2 Nm).
3. If removed, install the cooling tube.
4. Connect the electrical lead. Install the quarter panel trim cover.
5. Connect the battery cable.

Fig. 4: Auxiliary heating and A/C system

Hope this helps (remember to rate this answer).

everthing your looking for is on passenger side dash underneath blower heater core just remove bottom of cover and see if you can get to it..

replace the blower motor resistor located on the heater box were the blower motor is located the wiring to the blower may go to it. This is very easy to locate if you buy the part first.

under the hood on the passenger side near the fire. wall you will find the heater blower motor .there are about four small screws holding it on in a circleular patern . it also has a hire attached to it remove the wire and the cap screws .. when you remove it .you will have to take the plastic fan off the motor and transfer it on to the other motor .with the small clip that holds it on then install it the same way that you removed it ..

replace blower control module

well its an easy replacment unhook the power and ground wires on the motor remove the bolts and remove the motor install the new one

1.) remove screw from right door sill trim plate, (that piece of trim that covers the edge of the carpet when the door is open) 2.) remove right hinge pillar trim panel (passenger side kick panel) 3.) disconnect blower motor electrical connectors 4.) remove blower motor cover 5.) disconnect the cooling tube (rubber hose that attaches to the motor ) .6.) loosen courtesy light screws and move light out of way (if equipped) 7.)remove right side dash support bolt (under dash twist your head around like the excorsist, , lol , where the dash meets the side panel pillar) 8.)remove blower motor-to-case screws 9.) remove blower 10.) remove fan from blower motor shaft 11.) to install reverse removal procedure ,.. not as bad as it sounds , cheers.

check the "blower motor fuse" "heater fuse" and ac fuse and relay. these will be located under the dash on the drivers side usually mounted near the foot rest next to the door AND under the hood along the fender on the passenger side.