Question about 2000 Nissan Sentra

1 Answer

O2 Sensor Bank 1 Sensor 2 location

I got a p0141 code on my 2000 Nissan Sentra. I know it's O2 Sensor Bank 1 Sensor 2, but I'm not quite sure where it's at

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 53,746 Answers

Standing in front of the vehicle looking at the engine bank 1 sensor 2 is the sensor after the cat converter on the bank on your left
bank one is the left cat ---bank 2 is the right cat. Sensor 1 is the one before the cat and sensor 2 is the one after the cat on either side

Posted on Mar 15, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ZX2Fast
  • 547 Answers

SOURCE: what side is my o2 sensor (bank 1 sensor 1) on for

Bank one is on the side of cylinder one. Cylinder one is typically on the driver side. Although, you have to be careful here. Just because the code mentioned the O2 sensor doesn't mean the sensor is bad. For instance, a code of P0171: sensor indicates lean, bank one sensor; one is not a bad sensor. That is a good sensor telling you that the engine is running lean on bank one. If you get a different code, then it could the be the sensor.

Posted on Mar 05, 2010

Testimonial: "thank you !"

  • 265 Answers

SOURCE: 1996 Nissan Maxima o2 Sensor Location

check out www.maxima.org

Posted on Feb 05, 2010

  • 379 Answers

SOURCE: location of a o2 sensor 2001 nissan maxima

bank 1 refers to the side of the engine that #1 cylinder is on , and sensor 2 refers to downstream , after the catalytic converter. , this link shows bank 1 on a 2001 nissan maxima V6 being on the firewall side . if you had a 4 cylinder it would be downstream after the catalytic converter .

http://www.autozone.com/N,26200242/shopping/specsSelect.htm



Posted on Jan 04, 2009

  • 1986 Answers

SOURCE: where is 02 bank 2 sensor 1 placement on a 2001

Bank 1 means it's on the same side as your cylinder 1
Sensor 1 is the sensor that is located before the catalytic converter.

Posted on Sep 10, 2009

  • 1986 Answers

SOURCE: 2000 Nissan Sentra 1.8 with P071 trouble code, too

do you mean P0171??
If so, then it means your MAF sensor may be dirty and needs to either be cleaned or replaced.
It could also mean there's a vacuum leak downstream of the MAF sensor

Posted on Oct 13, 2009

Testimonial: "Confirmed what I suspected. Thanks, Lesjude"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi i have a 2002 ford ranger and it has teas codes P0446 P0135 P0141 P2195 P0403 P0171


P0446: EVAP System Vent Control Circuit http://www.autocodes.com/p0446_ford.html

P0135: O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1
P0135 Ford O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1

P0141: O2 Heater Circuit Bank 1 Sensor 2
P0141 Ford O2 Heater Circuit Bank 1 Sensor 2

P2195: Oxygen Sensor Signal Biased/Stuck Lean - Bank 1 Sensor 1
http://www.autocodes.com/p2195_ford.html

P0403:Exhaust Gas Recirculation Control Circuit http://www.autocodes.com/p0403_ford.html

P0171: Fuel Injection System Too Lean Bank 1 http://www.autocodes.com/p0171_ford.html

Nov 15, 2016 | 2002 Ford Ranger

1 Answer

How many o2 sensor are on a 2004 gmc yukon


Hi Charles,

GM products have 4 O2 sensors attached along the exhaust pipes coming off the manifold. Bank 1 is aligned to cylinder 1 on the engine which is the driver's side. Sensor 2 is the one after the convertor (Sensor 1 being the one before the convertor). Link attached for more information.

Oxygen Sensor Locations

I have changed out one of mine; quite easy, but you need a sensor wrench which you can find an any automotive store for around $15.

The part is available readily enough - link attached.

Good luck

Feb 07, 2015 | 2004 GMC Yukon

1 Answer

Po141 keeps coming on even though the part was changes and the code cleared from computer, why?


The P0141 code refers to your o2 sensor heater circuit. while many times replacement of the o2 sensor can solve this problem you possibly have a short or open in your o2 sensor heater circuit. Also was the proper o2 sensor changed p0141 is the bank 1 number 2 sensor. Bank 1 refers to the side of your engine where the #1 cylinder is located sensor 2 should be the second sensor on that side depending on how many sensors you vehicle has. hope this helps

Oct 12, 2013 | 2001 Chevrolet Impala

1 Answer

What does this mean p0141 for2001 nissan sentra


COULD BE OXYGEN SENSOR.Trouble Code: P0141

HO2S-12 (Bank 1 Sensor 2) Heater Circuit Malfunction

Possible Causes:


HO2S heater control circuit is open or shorted to ground.HO2S heater control circuit is shorted to power.HO2S heater is damaged or has failed.PCM has failed.

Jan 20, 2013 | 2001 Nissan Sentra

1 Answer

1996 honda accord o2 sensor versus Catalytic converter codes p0135 and p0141


The fault code P0135 means O2 Sensor Heater Circuit (Bank 1 Sensor 1)
The code P0141 means O2 Sensor Heater Circuit (Bank 1 Sensor 2)

Launch X431 Connector

Aug 22, 2012 | 1996 Honda Accord

1 Answer

What is diagnostic procedures for DTC p0135 & p0141


Oxygen Sensor problems... P0135 (Bank 1, Sensor 1) and P0141 (Bank 1, Sensor 2)

P0135 - Oxygen O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)
This code refers to the front oxygen sensor on Bank 1. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it.

The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135.

Symptoms: You will likely notice poor fuel economy the illumination of the MIL.

Causes: A code P0135 may mean that one or more of the following has happened:
O2 Heater element resistance is high
Internal short or open in the heater element
O2 heater circuit wiring high resistance
open or short to ground in the wiring harness

Possible Solutions:
Repair short or open or high resistance in wiring harness or harness connectors
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)



P0141 - O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2)
This code means that the heated circuit in the oxygen sensor on bank 1 decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0141.

Symptoms: You will likely notice poor fuel economy the illumination of the Check Engine Light.

Causes: A code P0141 may mean that one or more of the following has happened:
open or short to ground in the wiring harness
O2 heater circuit wiring high resistance
O2 heater element resistance is high
Internal short or open in the heater element

Note: Typically a failed catalytic converter does not cause this code. You're more likely to see a P0420 code for a failed converter.

Possible Solutions:
Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)
Repair short or open or high resistance in wiring harness or harness connectors


Hope this helps (remember to rate this answer)..

May 11, 2011 | 2000 Nissan Maxima

1 Answer

Location of o2 sensor bank 1 sensor 2


Bank 1 sensor 2 is the O2 sensor behind the catalytic converter.

Apr 08, 2011 | 1999 Nissan Sentra

3 Answers

Reccieved P0141, P0147, P0340 as emission diagnostic trouble codes. What do these mean?


P0141....O2 Sensor Heater Circuit (Bank 1 Sensor 2)

P0142....O2 Sensor Circuit Malfunction (Bank 1 Sensor 3)

P0143....O2 Sensor Circuit Low Voltage (Bank 1 Sensor 3)

P0144....O2 Sensor Circuit High Voltage (Bank 1 Sensor 3)

P0145....O2 Sensor Circuit Slow Response (Bank 1 Sensor 3)

P0146....O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 3)

P0147....O2 Sensor Heater Circuit (Bank 1 Sensor 3)

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

Sep 20, 2010 | 1997 GMC Sierra

2 Answers

I am getting a p0141 code, where is this sensor located


P0141-o2 sensor heater circuit malfunction [bank 1 sensor 2 ]this is the o2 sensor after the cat converter need to check the wiring[harness] and connections for frayed ,damaged or partial connection or o2 sensor failure and needs to be replaced

Mar 04, 2010 | Dodge Caravan Cars & Trucks

Not finding what you are looking for?
2000 Nissan Sentra Logo

506 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...