How do you reset the windshield wipers to the start position on a 97 camero? The stop In the middle off the window when turned off.

Sorry , no adjustment .
Wiper/Washer System Components
The Wiper / Washer System consists of the following components:
• Windshield wiper / washer switch
• Windshield wiper system module / motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR 25A fuse
Wiper / Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls the wiper motor operation. The windshield wiper motor is a 2 speed motor. Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wipe cycles. The DELAY interval is controlled through a series of resistors within the wiper / washer switch.
Park Position Operation
When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Do you know how to do diagnostic's ?

Wipers Blades Do Not Park
Step
Action
Yes
No
Schematic Reference: Wiper/Washer Schematics
Connector End View Reference: Wiper/Washer Connector End Views
DEFINITION: This table diagnoses the wipers operate normally but will not return to the park position when the wiper operation is cancelled.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Turn ON the ignition, with the engine OFF.
Move the wiper switch to the LO position.
Move the wiper switch to the OFF position.
Do the front wipers advance to the park position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn the ignition switch to the RUN position.
Turn the wiper switch to OFF.
Disconnect the wiper/washer switch connector.
Do the wipers park?
YES - Go to Step 7
NO - Go to Step 4
4
At the wiper/washer switch connector, measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 5
NO - Go to Step 8
5
Reconnect the wiper/washer switch connector.
Disconnect the wiper motor connector.
Measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 6
NO - Go to Step 8
6
Repair a short to battery positive voltage in the windshield wiper switch signal 2 circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you find and correct the condition?
NO - Go to Step 9
--
7
Replace the wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column - Tilt.
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

With ya'lls perty white heavy snow,it made your wipers get unaligned,you will have to remove and reset.It's not good to remove snow from wipers when windshield is loaded,get a scraper or blower and go at it.Wish we got snow.

Remove the linkage from the wiper motor. Turn the wipers on then off. This will set the motor in the park position. Move the wipers by hand to there normal off position. Reinstall the linkage onto the wiper motor. The wipers should now park or stop in the correct position.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

simple actually- 1- on wiper arms- flip up cap on end- remove nut, 2 using a screw driver and small wood block lift arms off driver screw.3 turn key on cycle wipers- turn off 4- reattach arms in correct position and retighten-., test with arms up- not on glass- is still wrong- the link from wiper motor to cross arm wrong- - buy a HAYES repair manual- will show how to remove cowl cover yourself- is easy , then follow instuctions in manual to correct link

There is a tab that bends and sometimes brakes. When you shut off the wipers the wiper motor reverses and is supposed to catch a tab to park the wipers. If the tab misses the catch they stop in the up position.

The intermittent function for the wipers has a variable resistor that controls the timing of the wipers in this mode. Replacement of the wiper switch will resolve this issue. Over time they do become worn, and do not make contact during the entire wiper cycle.

check to make sure the wipers are at its right angle on the vehicle, loose the nuts and place both wipers close to the bottom of the wind screen

It sounds like the the circuit board has gone bad and does not know where the base is any more so it will stop at the middle or the windshield. Auto Zone should have a new board if it's replaceable like the GM products. Good luck and hope this helps, In the mean time you can always turn your wipers on and pull the fuse out when it's at the down position so it's not up.

This is a commoon problem with what is called the "Park pawl stop". The tab is most likely bent and needs to be re-aligned, then the wipers need to be re-timed. This re-timing can be a little difficult, although the re-aligning of the tab is failry simple.

TechJK

try grounding the wipermotor housing.