Where is the reverse wire in a V6 2002 Mustang to connect to an AVIC X950BH Navigation AV receiver for the rear camera

Connect rear camera power lead "Red +12VDC" to back-up lamp circuit in trunk. Splice into back-up lamp wire near bulb. https://www.6ya.com/callphilipforhelp

You may already know "official replacement cameras" can cost $300 and more!

eBay has a REPLACEMENT CAMERA for $3.99
123112575223
Waterproof 170° Car Rear View Backup Reverse Parking Camera IR WITH Night Vision!

These cameras are VERY basic, SIMPLE and USUALLY have only a few connections:

12V+ (switched usually RED)*
12V- (or chassis ground usually BLACK)*
VIDEO Output: A "Shielded" cable (YELLOW).

*(note: The Camera 12V connections MAY have a connector attached as shown in RED below... cut it off).






UNMOUNT the original camera. Make these connections BEFORE you mount your NEW Camera...

1. CAREFULLY CUT and STRIP the new CAMERA wires 'as needed'

2. SOLDER the wires to your "ORIGINAL CAMERA CONNECTOR" (NOT at the CAR CONNECTOR)!

3. Tape your connections well!

4. TEST your new camera. HUZZZZZAAAAA!

Notes: It should be very easy to ID the VIDEO COAX. It should be somewhat larger than the other wires. The COAX may be somewhat 'delicate' so use care.

Don't worry if you have a few wires left over. You may find this number helpful: 19g490a

A 'AMAZON' reply said: ...'the part #19G490 but different preceding numbers. It came with a wiring harness that was for the Lincoln'...

Amazon com 2013 2015 Lincoln MKZ Trunk Panel Rear Back Up Camera Wiring...

Anthony
(SAY Thank You!)

open up the rear bulb compartment cover
and note the color wires running into the reverse light bulb holder

a hand full of fuses as you
use a LED test light or voltmeter to find the right wire

and use those color wires as your power /earth for the reverse camera

or you need the rear loom wiring diagram for that 2006 chev

The reverse light wire will not be under the dash, there will be a constant live feed from the fuse to the reverse light switch on the gearbox, that is no good for you. You need to take a power after the switch, that's live when reverse is selected. You may be able to pick this wire up from the loom, loom runs down the left hand side of the vehicle. Look at the wire colour to the reverse light at the rear and trace in the loom. at the front kick panel

Try this http://stereowiringdiagram.info/

it would be easier to run it from the back up wire in the rear you can see it better

You can ground the wire to any unpainted metal surface. Find a screw or bolt, loosen it, put the wire under it and re-tighten.

Hi i just ran a wire from the rear of the tail light its not hard to do or you can run it from the transmission switch which is were your Tbar where you select your gears

please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation

1. Release pin from locks by pressing release button under rear seat cushion.

1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .

1. To install, reverse Removal procedure.
   

----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal

1. Remove rear seat cushion as outlined.

1. Remove rear seat bolster. Refer to Section 01-05 .

1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
2. Remove four seat back to package tray retaining bolts.

1. Remove seat back.

1. To install, reverse Removal procedure.

here is some info:http://www.the12volt.com/installbay/stereodetail/845.html