Need the brake bleeding sequence

You have to bleed the whole system in sequence. It is a two man job. you have air in the system. You must bleed each wheel starting with the wheel farthest from the master cylinder. then the next wheel that shares the same circuit then the next and the next. Each car has its own sequence to follow. front wheel drive cars bleed differently than rear wheel cars . You must keep the master cylinder full as you do this, as to not allow any more air to enter the system. If air has entered the ABS system it will have to be bleed as well .. You have to refer to a manual for your car.

start with furthest from master cylinder, loosen bleed nipple then get someone to press and hold brake pedal, tighten nipple, repeat until no air. Remember to top up master cylinder, continue with next nearest till done

Most cars are done the same way:
1: Farthest brake from the master cylinder (rear)2: Opposite side from the first brake.3: Farthest from the master cylinder on the front.4: Remaining brake.
BTW: I would advice using the traditional method of using a clear bottle with some fluid in the bottom and a clear hose running out of the fluid, through the bottle top and which can connect to the bleed nipple. When bleeding fluid, make sure the fluid in both the master cylinder and to the bottle is clean before closing off the bleed nipple. Then pump the brake after bleeding each brake and feel for any softness. If you feel softness after bleeding any particular brake, then you will know that you just introduced air into that brake line, and will need to bleed again.NEVER allow your master cylinder to become totally empty whilst bleeding as this will mean you have to bleed all air out of the total system and start again from scratch. This can be a huge pain!

PRESSURE BLEEDING

MANUAL BLEEDING

Print
For vehicles equipped with an Anti-lock Brake System (ABS), please refer to the ABS bleeding procedure at the end of this section.
The purpose of bleeding the brakes is to expel air trapped in the hydraulic system. The system must be bled whenever the pedal feels spongy, indicating that compressible air has entered the system. It must also be bled whenever the system has been opened or repaired. If you are not using a pressure bleeder, you will need a helper for this job.

WARNING Never reuse brake fluid which has been bled from the brake system.

MASTER CYLINDER

See Figure 1
If the master cylinder is off the vehicle, it can be bench bled.

1. Secure the master cylinder in a bench vise.
2. Connect 2 short pieces of brake line to the outlet fittings, bend them until the free end is below the fluid level in the master cylinder reservoirs.
3. Fill the reservoir with fresh DOT 3 type brake fluid.
4. Using a wooden dowel, or equivalent, pump the piston slowly several times until no more air bubbles appear in the reservoirs.

Fig. Fig. 1: Attach bleeding tubes to the master cylinder and position them as shown

1. Disconnect the 2 short lines, refill the master cylinder and securely install the cylinder cap.
2. If the master cylinder is on the vehicle, it can still be bled, using a flare nut wrench.
3. Open the brake lines slightly with the flare nut wrench, while pressure is applied to the brake pedal by a helper inside the vehicle.
4. Be sure to tighten the line before the brake pedal is released.
5. Repeat the process with both lines until no air bubbles come out.
6. Bleed the complete brake system, if necessary.

If the master cylinder has been thoroughly bled and filled to the proper level upon installation into the vehicle, it is not necessary to bleed the entire hydraulic system.

PRESSURE BLEEDING

When bleeding the brakes, air may be trapped in the brake lines or valves far upstream, as much as 10 feet from the bleeder screw. Therefore, it is very important to have a fast flow of a large volume of brake fluid when bleeding the brakes, to make sure all of the air is expelled from the system.
On Cirrus, Stratus, Sebring convertible and Breeze models, the following wheel sequence should be used to ensure that all the air is removed from the system:


Left rear wheel Right front wheel Right rear wheel Left front wheel
On Sebring coupe and Avenger models, the following wheel sequence should be used to ensure that all the air is removed from the system:


Right rear wheel Left front wheel Left rear wheel Right front wheel

1. You should use bleeder tank tool C-3496-B or equivalent, with the required adapter for the master cylinder reservoir to pressurize the hydraulic system for bleeding. Make sure to follow the manufacturer's directions for using a pressure bleeder.
2. Attach a clear plastic hose to the bleeder screw located at the right rear wheel, then place the hose into a clean jar that has enough fresh brake fluid to submerge the end of the hose.
3. Open the bleeder screw at least one full turn or more to get a steady stream of fluid.
4. After about 4-8 oz. of fluid has been bled through the brake system and an air-free flow is maintained in the hose and jar, close the bleeder screw.
5. Repeat the procedure at all the other remaining bleeder screws. Then, check the pedal for travel. If pedal travel is excessive or has not improved, enough fluid has not passed through the system to expel all of the trapped air. Be sure to monitor the fluid level in the pressure bleeder. It must stay at the proper level so air will not be allowed to re-enter the brake system through the master cylinder reservoir.
6. Once the bleeding procedure is complete, remove the pressure bleeding equipment from the master cylinder.

MANUAL BLEEDING

See Figure 2
Proper manual bleeding of the hydraulic brake system will require the use of an assistant.
On Cirrus, Stratus, Sebring convertible and Breeze models, the following wheel sequence should be used to ensure that all the air is removed from the system:


Left rear wheel Right front wheel Right rear wheel Left front wheel
On Sebring coupe and Avenger models, the following wheel sequence should be used to ensure that all the air is removed from the system:


Right rear wheel Left front wheel Left rear wheel Right front wheel

Fig. Fig. 2: With a clear plastic hose in a container of clean brake fluid, open the bleeder screw at least one full turn

1. Attach a clear plastic hose to the bleeder screw located at the right rear wheel, then place the hose into a clean jar that has enough fresh brake fluid to submerge the end of the hose.
2. Have an assistant pump the brake pedal 3-4 times, and hold it down before the bleeder screw is opened.
3. Open the bleeder screw at least one full turn. When the bleeder screw opens, the brake pedal will drop.
4. Close the bleeder screw. Release the brake pedal only AFTER the bleeder screw is closed.
5. Repeat the procedure 4 or 5 times at each bleeder screw, then check the pedal for travel. If the pedal travel is not excessive, or has not been improved, enough fluid has not passed through the system to expel all of the trapped air. Make sure to watch the fluid level in the master cylinder reservoir. It must stay at the proper level so air will not re-enter the brake system.
6. Test drive the vehicle to be sure the brakes are operating correctly and that the pedal is solid.

If you have a manual for your vehicle, check how to bleed the system. Certain vehicles need to be bled in a certain order of sequence. If you are using a one man bleeding kit, when you don't see air bubbles in the clear tube but see only fluid, then it is bled properly.

The brake system bleeding procedure differs for ABS and non-ABS vehicles. The following procedure pertains only to non-ABS vehicles. For details on bleeding ABS equipped vehicles, refer to the ABS procedures later in this section.

WARNING Make sure the master cylinder contains clean DOT 3 brake fluid at all times during the procedure.

1. The master cylinder must be bled first if it is suspected of containing air. Bleed the master cylinder as follows:
   1. Position a container under the master cylinder to catch the brake fluid.
   2. Loosen the left front brake line (front upper port) at the master cylinder and allow the fluid to flow from the front port.
   3. Connect the line and tighten to 24 ft. lbs. (32 Nm).
   4. Have an assistant depress the brake pedal slowly one time and hold it down, while you loosen the front line to expel air from the master cylinder. Tighten the line, then release the brake pedal. Repeat until all air is removed from the master cylinder.
   5. Tighten the brake line to 24 ft. lbs. (32 Nm) when finished.
   6. Repeat these steps for the right front brake line (rear upper port) at the master cylinder.
      

WARNING Do not allow brake fluid to spill on or come in contact with the vehicle' finish, as it will remove the paint. In case of a spill, immediately flush the area with water.

1. If a single line or fitting was the only hydraulic line disconnected, then only the caliper(s) or wheel cylinder(s) affected by that line must be bled. If the master cylinder required bleeding, then all calipers and wheel cylinders must be bled in the proper sequence:
   1. Right rear
   2. Left front
   3. Left rear
   4. Right front
2. Bleed the individual calipers or wheel cylinders as follows:
   1. Place a suitable wrench over the bleeder screw and attach a clear plastic hose over the screw end.
   2. Submerge the other end in a transparent container of brake fluid.
   3. Loosen the bleed screw, then have an assistant apply the brake pedal slowly and hold it down. Close the bleed screw, then release the brake pedal. Repeat the sequence until all air is expelled from the caliper or cylinder.
   4. When finished, tighten the bleed screw to 97 inch lbs. (11 Nm) for the front, or 66 inch lbs. (7.5 Nm) for the rear.
3. Check the pedal for a hard feeling with the engine not running. If the pedal is soft, repeat the bleeding procedure until a firm pedal is obtained.

Fig. 1: Loosen the front brake line in order to bleed the master cylinder

Fig. 2: Connect a bleed hose from the bleed valve on the front caliper to a jar of brake fluid

Fig. 3: Always follow the lettered sequence when bleeding the hydraulic brake system

Hope this helps to solve it; remember to rate this answer.

When replacing any brake components it's always a great idea to bleed the brakes. Because your life depends on the serviceability of your brake system. When you open, crack or brake any line in your brake system, you automaticity introduce air into the system. Air can be compressed easily as opposed to brake fluid, which is designed not to compress as well as resist heat. The air in your system will cause your ABS and sensors to malfunction and or not work at all. When bleeding your brake system use this sequence start with: 1)right rear, 2)left rear, 3)front right, 4)front left. All vehicle parts and locations are referred to as the vehicle's left and right sides. Or as your setting in the drivers seat. Hope that helps.

normally, the brakes are bled starting from the furthest brake to the closest with respect to the master brake cylinder. the sequence is : right rear, left rear, right front, left front. pump the brakes until pressure is built up. do this rather slowly. while keeping downward pressure on the pedal, open the bleed screw slowly. the pedal will go to the floor. hold the pedal on the floor and tighten the bleed screw. do this until no air is observed. keep the reservoir. repeat with the rest of the brakes following in sequence

http://www.aa1car.com/library/2003/bf90347.htm

have you had problems getting pressure to the rear brakes before? if yes it is proportion valve problem if no try to sequence bleed the entire system starting with tire left rear, right rear, left front, right front. do the sequence 2-3 times.

Start from right rear, then, left rear, right front, left front. Fill master cylinder. Have helper sit in car, have helper hold brake pedal down. open bleed screw. fluid and air comes out. close screw. release brake pedal. Continue until no air comes out. Move to next wheel. Keep an eye on master cylinder fluid level after each wheel.