Question about Subaru Tribeca

Open Question

How to change Serpentine Belt on subaru tribec 2007

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 18 Answers

SOURCE: 2007 scion tc 2.4L-serpentine belt

Yes I do i am a specialist for the Scion tC and its 2.4L power plant if you need this diagram please email me at 08TurboScion@comcast.net

Regards:

Chad Buckwalter, Master Toyota/Scion Performance Technician

Posted on Jul 21, 2008

Ad
abauto
  • 353 Answers

SOURCE: how do i change a serpentine belt for a 2007

Drive Belt: Service and Repair
DRIVE BELT

Components
43931e7.jpg


REMOVAL
1. REMOVE V-BANK COVER SUB-ASSEMBLY
2. REMOVE NO. 1 ENGINE UNDER COVER

4cff58f.jpg



3. REMOVE FAN AND GENERATOR V BELT
(a) While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and
then insert a bar of [diameter]5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.
HINT: The pulley bolt for the belt tensioner has a left-hand thread.
(b) Remove the V belt.



1. INSTALL FAN AND GENERATOR V BELT
(a) Set the V belt onto every part.
(b) While turning the belt tensioner counterclockwise, remove the pin.
NOTICE: Make sure that the V belt is properly set to each pulley.
(c) After installing the belt, check that it fits properly in the ribbed grooves.
HINT: Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.
2. INSTALL NO. 1 ENGINE UNDER COVER
3. INSTALL V-BANK COVER SUB-ASSEMBLY

c0b77ac.jpg

Posted on Sep 30, 2009

  • 484 Answers

SOURCE: serpentine belt

<img src="http://www.mvreader.com/multiview/dayco/graphics/rtdiag/bkc.jpg" alt="2003 SUBARU OUTBACK - H6 3.0L 3000cc GAS FI N EZ30D" /><br>The website mvreader.com/multiview/dayco has listings for most cars' serpentine belts, as well as their installation instructions.

Hope this helps out,
matthew

Posted on Oct 22, 2009

  • 484 Answers

SOURCE: how to change serpentine belt on 207 toyota camry

4 cylinder diagram
6 cylinder diagram
Loosen the tensioner pulley to remove the belt. It is the one that has a long bolt running through it. Once you remove the old belt, install the new one using the appropriate diagram from the above two links. Readjust the tension using the bolt you loosened to remove the old belt.

i hope this helps
matthew

Posted on Nov 20, 2009

  • 538 Answers

SOURCE: 2007 chrysler sebring serpentine belt diagram

Go to; daycoproducts.com, click cars and trucks, then go to serpentine belt. Then on the right side of the screen click on finding your vehicle. Then get the illistration number and click on illistrations, go to that number it should something 6-? or 7-?. It's a pretty good websight.

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I just needa serpentine belt diagram for a 2006 subaru tribeca


Diagram reference number 1 in the image below:
7540040.gif"" Fitment: 2006 SUBARU B9 TRIBECA - 4 door

Application Notes:

Category: Electrical. Charging and Starting

SubCategory: Alternator / Generator and Related Components

Position: General

Part Number: 809221090


This is a Serpentine Belt that fits the 2006 SUBARU B9 TRIBECA - 4 door with the EZ30D engine. The Serpentine Belt is designed by SUBARU to be part of the Electrical. Charging and Starting-Alternator / Generator and Related Components. The Serpentine Belt has a position on the vehicle of General. The 2006 SUBARU B9 TRIBECA Serpentine Belt is a factory made SUBARU OEM part and it comes with a 12 month 12.000 mile warranty (parts only). Do not be fooled by an aftermarket SUBARU B9 TRIBECA Serpentine Belt! Buy a factory SUBARU part and receive peace of mind!
This factory part has a part number of 809221090. " clear1x1.gif dbox_border_left_bottom.gif clear1x1.gif dbox_border_right_bottom.gif clear1x1.gif

2_12_2013_10_59_21_pm.gif

Dec 14, 2012 | 2006 Subaru B9 Tribeca

1 Answer

I need a diagram of serpentine belt route for 2007 subaru b9 tribeca


sometimes they are on a sticker under the hood

Nov 30, 2012 | Cars & Trucks

1 Answer

Where can I get the diagram of the serpentine belt for my 2007 honda crv please?


Alot of times there is a sticker under the hood with the diagram on it,or make one of your own before you remove the belt.

Aug 24, 2012 | Cars & Trucks

1 Answer

How simple is it to change a alternator belt on subaru svx?


  1. Removing the Serpentine Belt
    • 1 Park your Subaru on a level surface and open the hood.
    • 2 Disconnect the ground (black) battery cable using a wrench. This will prevent the cooling fan from activating.
    • 3 Locate the serpentine belt routing diagram in your engine compartment and compare it to the actual routing of the installed belt. Make sure the routing on the label matches the actual routing. If they do not match or there is no label, note the actual routing on a piece of paper for later reference.
    • 4 Locate the belt tensioner pulley on your Subaru model. If the tensioner is equipped with a squared hole, use a large breaker bar with a 1/2-inch (13 mm) drive. Otherwise, use a ratchet and socket of the proper size on the tensioner pulley center bolt.
    • 5 Rotate the tensioner pulley away from the belt to release the belt tension.
    • 6 Pull the belt off of one of the pulleys and slowly release the tensioner pulley back into position. Do not let the tensioner pulley snap back or you may damage an internal component.
    • 7 Finish removing the serpentine belt from the rest of the pulleys and the engine compartment.
    Installing the New Serpentine Belt
    • 1 Match the old belt to the new one and make sure they are of the same length and configuration. It is normal for the new belt to be slightly shorter since the old one has been stretched through use.
    • 2 Route the new serpentine belt through all of the pulleys except the tensioner pulley. Use the diagram on the engine compartment or your notes, as a reference, to properly route the belt.
    • 3 Insert the large breaker bar into the square hole or the ratchet and socket into the tensioner pulley center bolt.
    • 4 Rotate the tensioner pulley in the same direction you did to release the belt tension.
    • 5 Slide the serpentine belt onto the tensioner pulley.
    • 6 Release the tensioner pulley back into position.
    • 7 Look at all the pulleys and make sure the serpentine belt is properly seated on each one. Otherwise, release the belt tension and adjust the belt.
    • 8 Connect the ground (black) battery cable using the wrench.

Oct 18, 2011 | 1992 Subaru SVX

1 Answer

The serpentine belt broke on my2002 subaru outback


There is a distinct possibilty there is engine damage caused when the belt broke. It is best not to turn the engine at all once this happens. Sometimes you can be lucky and there be no damage. Let's hope that's so in your case. These belts are supposed to be replaced every 100,000km.

Download instructions from my website...

http://arraw.info/pdf/Timing Belt.pdf

Feb 20, 2010 | 2002 Subaru Outback

1 Answer

How to change serpentine belt on 207 toyota camry


4 cylinder diagram
6 cylinder diagram
Loosen the tensioner pulley to remove the belt. It is the one that has a long bolt running through it. Once you remove the old belt, install the new one using the appropriate diagram from the above two links. Readjust the tension using the bolt you loosened to remove the old belt.

i hope this helps
matthew

Nov 20, 2009 | 2007 Toyota Camry

1 Answer

Serpentine belt


<img src="http://www.mvreader.com/multiview/dayco/graphics/rtdiag/bkc.jpg" alt="2003 SUBARU OUTBACK - H6 3.0L 3000cc GAS FI N EZ30D" /><br>The website mvreader.com/multiview/dayco has listings for most cars' serpentine belts, as well as their installation instructions.

Hope this helps out,
matthew

Oct 22, 2009 | 2003 Subaru Outback

2 Answers

Changing serpentine belt 3.8 2007 pontiac grand


  • Make sure your new belt exactly matches the old belt demensions
  • Take a breaker bar or big rachet & release the tension on the automatic tensioner; very slowly
  • Loop the old belt around the pulleys & fan
  • Install new

Oct 17, 2009 | 2007 Pontiac Grand Prix GXP Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

379 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...