1997 Jaguar XK8 Logo

Related Topics:

R
Ray Pike Posted on Feb 20, 2014
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Trying to install glass cover over hole at bottom of headlight, but glue seems only option as there is no apparent clips or gaskets for two prongs. Do I glue this in place?

Answer This Question

1 Answer

Don Cahala

Level 2:

An expert who has achieved level 2 by getting 100 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Novelist:

An expert who has written 50 answers of more than 400 characters.

  • Expert 239 Answers
  • Posted on Jan 03, 2015
Don Cahala
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Novelist:

An expert who has written 50 answers of more than 400 characters.

Joined: Nov 29, 2011
Answers
239
Questions
0
Helped
63021
Points
469

The dealer will have a clear adhesive they recommend and sell over their parts counter. If they do not, ask the person behind the counter, and quite often they will have a recommendation. I might use clear silicone, but I'd prefer the recommended adhesive. Good luck and let us know your outcome so others may share.

1 Related Answer

Anonymous

  • 56 Answers
  • Posted on Mar 06, 2010

SOURCE: headlight area missing small triangle shape curved glass

It is the cover for the headlamp washer jet. Some XK's did nt have the jet fitted but they still had the cover

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Headlight gap cover installation
the item you are talking about is the cover for the headlamp washer jet has it got headlamp wash? if so the washer jet has fallen off the headlamp and dropped in the bumper liner, the cover clips on to end of jet if it does not have headlamp wash the cover has 2 clips one on each side but they break and fall off in that case we use epoxy glue to refit it
Read full answer
Feb 20, 2014 • 1997 Jaguar XK8
tip

How to replace the headlamp bulbs in 98 and newer Lincoln Town Cars
In order to replace the bulbs,the headlight assemblies need to be removed from the car.The following instructions make it easy.
The headlights and the grill have a top cover with clips that are unscrewed to remove it..There are about 6 of them.After the cover removal,remove the headlight assembly by pulling up on the two metal tabs on each light assembly or on the later models the few bolts holding in the light assembly.There is an access hole for a 1/4 inch extension to fit through for the bottom bolt.The bolts are 10mm.Then in the middle of the light assembly there is also a plastic tab that must be pushed down with a screwdriver and then the light assembly comes out.Once the electrical connectors are unplugged,the headlight assembly can be removed from the car ,put face down on a towel and disassembled so that the bulbs can be replaced.
The older versions have plastic tabs holding the back covers on,and the newer versions have T 27 torx screws holding the covers together.After the back cover is removed,you will see a collar that holds in the electrical socket that connects to the bulb. mark the collar position with a felt pen.Rotate the collar counterclockwise to remove it.The bulb and socket are then separated and the new bulb installed.Make sure the collar goes on first,as it will not slide over the bulb,only the bulb connector.Seat the new bulb,install the plug onto the bulb then the lock collar and reinstall the back covers.Do not touch the glass bulb surface with your fingers,as the oil will cause the glass to shatter when hot.Handle the bulb by the base only.
Before installing the light assembly into the car plug in the main connectors and check that the light works. If all is o.k., re-install the light into the car.After that, check to make sure that the lock tabs are all in place.Re- install the grill cover and the clips.Make sure that the hole in the grill cover on the driver's side goes over the hood switch for the alarm properly.Check final operation after re-assembly of all pieces.
Read full tip
on Apr 26, 2010 • Lincoln Town Car Cars & Trucks
0helpful
1answer

Headlight covers have condensation on glass
put plastx on the and then buff it up. it should fix the problem, if not then there may be a crack on the headlight where water is going in through. look for any cracks/holes/gaps. have them glued with silicone glue, make sure get water out first.
Read full answer
Jun 07, 2011 • 2001 Cadillac DeVille
3helpful
1answer

The brackets that attach to the driver's window on my son's 2003 Grand Am have broken due to forcing a frozen window. The window is no longer attached to the slide mechanisms. I am wondering...
Hello, normally just the window sashes break. this is the plastic part that is glued on the bottom of the glass. you can but these asahes at your dealer. they simply just glue on with a special glue

Sash Channel Came Off Glass; Adhesive on Glass
  1. Remove the door glass and lay it on a protected table.
  2. Mark the location of the clip with tape.
  3. Remove the adhesive with a one edge razor blade.
  4. Clean the glass with Isopropyl alcohol.
    5. Important: Install adhesive into the applicator and squeeze some adhesive out before you install the mixing tube. After the mixing tube is installed, run a test bead the length of the mixing tube to ensure a good mix.
  5. Fill the sash channel clip with adhesive.
  6. Install the clip in the marked location.
  7. Reinstall the door glass and put the glass in the full up position for 24 hours.

Cut off the bottom edge of the guide with a cut off wheel. (Refer to the illustration above.)

Using a thin flat blade putty knife and a hammer, carefully remove the plastic piece on each side of the glass. (Refer to the illustration above).

  • Clean any adhesive from the glass using a one-edge razor blade. (Refer to the illustration above).
  • Clean the glass with Isopropyl alcohol.
    • Important: Install adhesive into the applicator and squeeze some adhesive out before you install the mixing tube. After the mixing tube is installed, run a test bead the length of the mixing tube to ensure a good mix.
  • Fill the sash channel clip with adhesive.
  • Install the clip in the marked location.
  • Reinstall the door glass and put the glass in the full up position for 24 hours.

    • 22689012
    Sash, Side Door Window
    12378568 (US)
    88901676 (Canada)
    Structural Urethane Installation Adhesive
    mrtechwrench_28.gif
    Read full answer
    Jun 06, 2011 • 2003 Pontiac Grand Am
    0helpful
    1answer

    How do you get the back off of a rearview mirror to stick it back n the window
    Some have a cover hiding the screw or from the bottom theres a clip that need to be pryed back and held while you slide mirror of bracket, if theres no screw on the mirror to loosen then theres a clip arm holding it, also make sure to glue the right way take note of how it goes on because once you glue to glass its not coming off.
    Read full answer
    Dec 07, 2010 • 2004 Kia Optima
    0helpful
    2answers

    I am trying to replace the timing chain cover and can not get access because of the oil pan. I can not get the oil pan down far enough to get the timing cover on.
    This, Problem is not uncommon. I assume the truck has a V8 Engine.
    When you, removed the cover I'm sure you needed to pry the cover
    from the block Not a lot of pressure but, still a little pressure.
    Now, Trying to replace the cover is a little more troublesome.
    First, You, need to be sure the cover is clean extremely clean.
    Especially at the bottom where the seal is.there's a thin steel
    gasket holder. Make sure the that area has NO oil on it.
    Next, You'll need to shave, cut,grind a little bit of the inside
    lip off the top of that steel gasket holder, Not a lot 1/4 inch
    should work.at the top where the steel stops. Angle the cut= \ Then
    Glue the Gasket to the cover. Wait, WAIT till the glue is dry don't install
    to block till gasket is on GOOD AND SOLID. When ready you can lube
    the bottom of the casket so it slides better. All the above will help the
    cover easer to install.What type of glue ? Yellow trim glue, any glue will work as long as its good. and the seal woun't move.
    Read full answer
    Mar 13, 2010 • 2000 GMC Jimmy
    2helpful
    1answer

    Change headlight bulb
    Removal & Installation Bulb Replacement To Remove:
    1. Release the spring clip and remove the protective cover from the rear of the bulb.
    2. Disconnect the electrical connector from the bulb.
    3. Remove the spring clip and remove the bulb from the headlight housing.
    To Install:
    CAUTION
    Do not touch the glass portion of the new bulb with bare hands.
    1. Insert the bulb in the housing.
    2. Secure the bulb with spring clip.
    3. Connect the electrical connector to the bulb.
    4. Install the protective cover on the headlight assembly.
    Headlight Assembly
    Read full answer
    Jul 16, 2009 • 2004 Volkswagen Jetta
    0helpful
    2answers

    How do i replace/remove the headlights from a 97 accord?
    1. Locate the headlight bulb that needs to be replaced. NOTE: It may be necessary to remove a component or the composite headlight assembly to gain access to the bulbs.
    2. Turn the headlights off.
    3. Detach the two prong connector from the base of the headlight bulb.
    4. Twist the bulb counterclockwise to unlock it from the headlight housing, then carefully withdraw the bulb from the housing. WARNING
      Do not touch the glass part of the bulb with your fingers. The pads of your fingers contain oils that will cause premature bulb failure. To install:
    5. Install a new bulb into the headlight housing, then turn it 1⁄4 turn to lock it into place.
    6. Attach the 2 prong connector to the bottom of the bulb.
    7. Turn the headlight switch on to make sure the bulb works, then turn the switch off.
    8. Install any components that were removed to get to the headlight bulb.
    Read full answer
    Mar 29, 2009 • 1997 Honda Accord
    1helpful
    1answer

    How to change headlight in 2000 chrysler sebring convertible
    There is a cover over the bulb that is removed by turning counter clockwise. (as viewed from the back of the housing)
    Remove the spring clip that holds the bulb and pull out bulb.
    Plug in new bulb (do not touch glass with hands) and install re-install spring clip and back cover.
    Read full answer
    Mar 15, 2009 • 2000 Chrysler Sebring
    0helpful
    1answer

    How to take the light out on a toyota corolla front headlight
    If you have the same set-up as a lot of newer cars then it is not as hard as it may seem. This is an older post but someone else may find the information and be able to use it. When you open the hood on the inside there should be an electrical connection going to the headlights. Where that goes in to the headlight compartment there should be a rubber covering. Remove this rubber covering and disconnect the electrical connection. Once the cover and connection are out of the way you should be able to have access to the bulb. On a lot of newer cars, they have a contraption to hold the bulb in place the looks like a paper clip that has been bent in a lot of odd angles. If this is the system that you have it is easy from this point. At the bottom there is a slot that holds the paper clip (that's what I call it) in place and keeps pressure on the bulb to hold it in place. Apply pressure near the bottom and slide it to get it to release from the slot. At that point it simply swings up and the bulb is free to come out. Put the new bulb back in. Swing the paper clip thing back down and place the bottom end of it back in the slot. Replace the rubber covering making sure the prongs are all sticking out and then replace the electrical connection. Do the other side, it is always best to do headlights in pairs
    Read full answer
    Dec 26, 2008 • 2003 Chevrolet Tracker
    Not finding what you are looking for?

    View Most Popular

    1997 XK8

    • Cars & Trucks

    Related Question

    Headlight gap cover installation

    • 1997 Jaguar XK8

    Related Topics

    77 views

    Ask a Question

    Usually answered in minutes!

    Popular Questions

    Jaguar XK8 Window Problem

    1998 Jaguar XK8

    ABS Light And Stability controll light

    1998 Jaguar XK8

    I know were the fuse

    Jaguar XK8 Cars & Trucks

    XK8 abs module

    1998 Jaguar XK8

    I need serpentine belt routing for 1999 Jaguar XK8

    1999 Jaguar XK8

    Check Out the Latest Top Trucks Report!
    Check Out the Latest Top Trucks Report!

    View all Fixya Reports

    Top Jaguar Experts

    ZJ Limited
    ZJ Limited

    Level 3 Expert

    17989 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6988 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    15088 Answers

    Are you a Jaguar Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...