How do I set the DOHC's timing on a 2000 Chrysler Concorde 2.7? I understand the procedure for the primary timing chain. Crankshaft sprocket (aligning w/oil pump mark) and both intake camshaft sprockets aligned w/colored chain links. WHAT is the timing position for the EXHAUST camshafts in relation to the Intake Camshafts? The camshafts, secondary chains and tensioners have been removed.

TDC related to piston one and should be as such.

Did you take pictures while removing the originals? It's always a good habit. Below are the instructions you need to follow. Your own pics are very helpful when doing a big job like this.

1. Disconnect negative battery (1) cable.
2. Drain cooling system.
3. Remove upper intake manifold.
4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.

CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.

1. Align crankshaft sprocket timing mark to mark on oil pump housing (2). The mark on oil pump housing is 600 ATDC of #1 cylinder.

CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage.

1. Remove primary timing chain tensioner retainer cap (2) and tensioner (1) from right cylinder head.

1. Disconnect and remove camshaft position sensor (4) from left cylinder head.
2. Remove timing chain guide access plugs (3) from cylinder heads.

NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction.

1. Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper (1) (if equipped) and sprocket.
2. Remove left side camshaft sprocket attaching bolts and remove sprocket.
3. Remove lower chain guide (7) and tensioner arm (8).
4. Remove the primary timing chain (5).
5. Remove crankshaft sprocket (6).

INSTALLATION

1. Inspect all sprockets (4,9,11) and chain guides (2,5,10). Replace if worn.
2. For crankshaft sprocket installation procedures Refer to CRANKSHAFT SPROCKET.
3. If removed, install right and left side short chain guides (11). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
4. Align crankshaft sprocket timing mark to the mark on oil pump housing (3).

NOTE: Lubricate timing chain and guides with engine oil before installation.

1. Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (1).

1. Lower the primary chain with left side sprocket through the left cylinder head opening.

NOTE: The camshaft sprockets can be allowed to float on the camshaft hub during installation.

1. Loosely position left side camshaft sprocket over camshaft hub.
2. Align timing (plated) link to the crankshaft sprocket timing mark (3).
3. Position primary chain onto water pump drive sprocket (10).
4. Align right camshaft sprocket timing mark to the timing (plated) link on the timing chain (8) and loosely position over camshaft hub.
5. Verify that all chain timing (plated) links are properly aligned to the timing marks on all sprockets.
6. Install left side lower chain guide (2) and tensioner arm (5). Tighten attaching bolts to 28 Nm (250 inch lbs.) .

NOTE: Inspect O-ring on chain guide access plugs before installing. Replace O-ring as necessary.

1. Install chain guide access plugs to cylinder heads. Tighten plugs to 20 Nm (15 ft. lbs.) .

NOTE: To reset the primary timing chain tensioner, engine oil will first need to be purged from the tensioner.

1. Purge oil from timing chain tensioner using the following procedure:

1. Place the check ball (2) end of tensioner into the shallow end of Special Tool 8186 (3).
2. Using hand pressure, slowly depress tensioner until oil is purged from tensioner.

1. Reset timing chain tensioner using the following procedure:

1. Position cylinder plunger (4) into the deeper end of Special Tool 8186 (3).
2. Apply a downward force until tensioner is reset.

NOTE: If oil was not first purged from the tensioner, use slight finger pressure to assist the center arm pin of Special Tool 8186 to unseat the tensioner's check ball.

CAUTION: Ensure the tensioner is properly reset. The tensioner body (4) must bottom against the top edge of Special Tool 8186 (3). Failure to properly perform the resetting procedure may cause tensioner jamming.

NOTE: Inspect the tensioner O-ring (2) for nicks or cuts and make sure the snap ring (1) is correctly installed, replace as necessary.

1. Install the reset chain tensioner (1) into the right cylinder head.
2. Position tensioner retaining plate (2) and tighten bolts (1) to 12 Nm (105 inch lbs.) .

1. Starting at the right cylinder bank, first position the camshaft damper (1) (if equipped) on camshaft hub, then insert a 3/8 square drive extension with a breaker bar into intake camshaft drive hub. Rotate camshaft until the camshaft hub aligns to the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and tighten to 28 Nm (250 inch lbs.) .
2. Turn the left side camshaft by inserting a 3/8 square drive extension with a breaker bar into intake camshaft drive hub and rotate camshaft until the sprocket attaching bolts can be installed. Tighten sprocket bolts to 28 Nm (250 inch lbs.).
3. Rotate engine slightly clockwise to remove timing chain slack, if necessary.

1. Activate the timing chain tensioner by using a flat bladed pry tool to gently pry tensioner arm towards the tensioner slightly. Then release the tensioner arm. Verify the tensioner is activated (extends).

1. Install camshaft position sensor (2) and connect electrical connector.
2. Install the timing chain cover, crankshaft vibration damper, and cylinder head covers.
3. Install upper intake manifold.

NOTE: After installation of a reset tensioner, engine noise will occur after initial start-up. This noise will normally disappear within 5-10 seconds.

1. Fill cooling system.

Remove camshaft covrs
Remove front cover
Remove or fully retract all three timing chain tensioners
Remove oil pump
Primary and secondary chain guides should remain in place. Rotate crankshaft until sprocket drive key is at about 1 o'clock position.
Set crankshaft and intermediate shaft sprockets into primary drive chain with their timing marks asjacent to each other.
Install crankshaft and intermediate sprockets over their respective shafts. Rotating crankshaft as necessary to engage crankshaft key in sprocket without changing the timing mark relationship.
Install Flywheel Holder Tool (J-39411) to lock crankshaft in position. Install intermediate shaft sprocket retaining bolt and torque to specifications.
Route secondary chain for left cylinder head over inner row of intermediate shaft teeth.
Route secondary drive chain over chain guide, and install exhaust cam sprocket to chain so camshaft drive pin engages the sprocket notch marked "LE" (Left Exhaust).
There dhould be no slack in the lower section of the chain, and the camshaft drive pin must be perpendicular (90 degrees) to the cylinder head surface.
Install the intake camshaft sprocket into the chain so the sprocket notch marked "LI" (Left Intake) engages camshaft drive pin, while drive pin remains perpendicular to the head face. Minor adjustments can be made to camshaft position to get pin to engage by using a wrench on the hex cast into the camshaft.
Install sprocket retainer bolts and torque to specification.
Repet steps as above to install the right secondary chain to the right camshafts. The right camshaft sprockets are marked "RE" and "RI". In addition, the RE sprocket must contain the camshaft position sensor pickup.

If you just want to check the timing marks on your Dodge 4.7L engine, skip ahead to step #32 of the procedure below.

I found this Dodge 4.7L engine info in a manual for the 2000 Durango 4WD
MFI 8 Cylinder, but whatever year your SUV/truck may be, all Dodge 4.7's should be the same.
I tried to post the entire procedure (with 5 illustrations), but got an error.
Happy Thanksgiving FunnyJennifer/Josh, and may your 4.7 keep perfect time.

Excerpt from Timing Chain & Sprocket Removal & Installation:
Dodge Durango 4.7L MFI 8 Cylinder
------------------------------------------------------------------------------------------
#32 Rotate the engine two full revolutions. Verify alignment of all timing marks:

Primary chain idler sprocket: dot at 12 o'clock

Primary chain crankshaft sprocket: dot at 6 o'clock

Secondary chain camshaft sprockets: V8 marks at 12 o'clock

Timing Chain and Sprockets REMOVAL & INSTALLATION 2.3L and 2.4L Engines The following tools will be required to perform this procedure:

• Camshaft sprocket timing alignment pins - J 36008 or equivalent
• Camshaft sprocket wrench - J 39579 or equivalent

2. Fig. 1: View of the DOHC engine "timed position'' - 2.3L and 2.4L engines
   Fig. 2: View of the SOHC engine "timed position'' - 2.3L engine
   
3. Remove the timing chain guides. There are usually three.
4. Raise and safely support the front of the vehicle.
5. Make sure all of the slack is above the tensioner. Gently pry off timing chain tensioner spring retainer, then remove the spring. NOTE: On the 2.3L engine two styles of tensioners are used. Early production engines will have a spring post and late production ones will not. Both styles are identical in operation and are interchangeable.
   
6. Remove the timing chain tensioner shoe retainer.
7. Make sure all the slack in the timing chain is above the tensioner assembly; remove the chain tensioner shoe. The timing chain must be disengaged from the wear grooves in the tensioner shoe in order to remove the shoe. Slide a suitable small prybar under the timing chain while pulling shoe outward.
8. If difficulty is encountered while removing chain tensioner shoe, proceed as follows:
   1. Lower the vehicle.
   2. Hold the intake camshaft sprocket with a camshaft sprocket wrench - J 39579 or equivalent holding tool and remove the sprocket bolt and washer.
   3. Remove the washer from the bolt and re-thread the bolt back into the camshaft by hand. The bolt provides a surface to push against.
   4. Remove intake camshaft sprocket using a 3-jaw puller in the 3 relief holes in the sprocket. NOTE: Do NOT try to pry the sprocket off the camshaft or damage to the sprocket or chain housing could occur.
      
9. Unfasten the tensioner assembly attaching bolts, then remove the tensioner. CAUTION
   The tensioner piston is spring loaded and could fly out causing personal injury. Use care when removing.
   
10. Matchmark the timing chain outer surface for reassembly purposes.
11. If equipped, remove the chain housing to block stud, which is actually the timing chain tensioner shoe pivot.
12. Remove the timing chain.
13. Inspect the parts for wear, then replace if necessary. Some scoring of the timing chain shoe and guides is normal. Clean the old sealant off of the bolt with a wire brush. Clean the threaded hole in the camshaft with a round nylon bristle brush. To install: WARNING
    Failure to following installation procedures can result in severe engine damage.
    
14. Install the intake camshaft sprocket onto the camshaft with the marked surface showing. Install the sprocket retaining bolt and washer. Use an adhesive compound 12345493 or equivalent on the bolt. Tighten the bolt to 52 ft. lbs. (70 Nm), while holding the sprocket with tool J-36013, J 39579 or equivalent, if removed.
15. Install tool J 36800 or equivalent, through hole(s) in the camshaft sprocket(s) into the holes in the timing chain housing. This positions the camshafts for correct timing. Fig. 3: Placing the camshaft sprockets onto the marked surface of the camshaft
    
16. If the camshafts are out of position and must be rotated more than 1?8 turn in order to install the alignment dowel pins:
    1. The crankshaft must be rotated 90°clockwise off of TDC in order to give the valves adequate clearance to open.
    2. Once the camshafts are in position and the dowels installed, rotate the crankshaft COUNTERCLOCKWISE back to TDC. NOTE: Do NOT rotate the crankshaft clockwise to TDC, or valve and piston damage could occur. WARNING
       The side of the timing chain that was marked must be facing outward when installed.
       
17. For DOHC engines only, install the timing chain over the exhaust camshaft sprocket, around the idler sprocket and around the crankshaft sprocket.
18. Remove the alignment dowel pin from the intake (DOHC only) camshaft. Using dowel pin remover tool J 39579 or equivalent, rotate the intake (DOHC only) camshaft sprocket counterclockwise enough to slide the timing chain over the intake (DOHC only) camshaft sprocket. Release the camshaft sprocket wrench. The length of chain between the two camshaft sprockets will tighten. If properly timed, the intake camshaft alignment dowel pin should slide in easily. If the dowel pin does not fully index, the camshafts are not timed correctly and the procedure must be repeated. Fig. 4: Place the timing chain over the exhaust camshaft and around the idler sprocket and around the crankshaft sprocketDOHC engines
    
19. Leave the alignment dowel pins installed.
20. Raise and safely support the vehicle.
21. With slack removed from chain between intake camshaft sprocket (camshaft sprocket for SOHC engines) and crankshaft sprocket, the timing marks on the crankshaft and the cylinder block should be aligned. If marks are not aligned, move the chain one tooth forward or rearward, remove the slack and recheck the marks.
22. If equipped, tighten the chain housing to block stud. The stud is installed under the timing chain. Tighten to 19 ft. lbs. (26 Nm).
23. For vehicles through 1991, reload timing chain tensioner assembly to its "zero'' position as follows:
    1. Assemble restraint cylinder, spring and nylon plug into plunger. Index slot in restraint cylinder with peg in plunger. While rotating the restraint cylinder clockwise, push the restraint cylinder into the plunger until it bottoms. Keep rotating the restraint cylinder clockwise but allow the spring to push it out of the plunger. The pin in the plunger will lock the restraint in the loaded position.
    2. Install tool J-36589 or equivalent, onto plunger assembly.
    3. Install plunger assembly into tensioner body with the long end toward the crankshaft when installed.
24. For 1992-98 vehicles, reload timing chain tensioner assembly to its "zero'' position as follows:
    1. Form a keeper from a piece of heavy gauge wire. See the accompanying figure.
    2. Apply slight force on the tensioner blade to compress the plunger.
    3. Insert a small prybar into the reset access hole, then pry the racket pawl away from the ratchet teeth while forcing the plunger completely in the hole.
    4. Install the keeper between the access hole and the blade. Fig. 5: View of reloading the timing chain tensioner assembly to its "zero'' position - 1992-98 vehicles
       
25. Install the tensioner assembly to the chain housing. Recheck the plunger assembly installation. It is correctly installed when the long end is toward the crankshaft.
26. Install and tighten timing chain tensioner bolts. Tighten to 89 inch lbs. (10 Nm).
27. Install the tensioner shoe and tensioner shoe retainer. Remove the special tool J-36589, then squeeze the plunger assembly into the tensioner body to unload the plunger assembly.
28. Lower vehicle enough to reach and remove the alignment dowel pins.
29. Rotate crankshaft clockwise (normal rotation) two full rotations. Align the crankshaft keyway with the mark on the cylinder block, then reinstall the alignment dowel pins. The pins will slide in easily if the engine is timed correctly. WARNING
    If the engine is not correctly timed, severe engine damage could occur.
    
30. Install the timing chain guides and, if equipped, the crankshaft oil slinger.
31. Install the timing chain front cover. For details, please refer to the procedure located in this section.
32. Connect the negative battery cable, then start the engine and check for oil leaks.

Discoverd this indepth expalaination of process steps involved in the installation of the timing chain from an ASE certified technician. I hope this helps. See the repair manual on the link below.<br /> <br /> Link: <a href="http://www.2carpros.com/forum/2002-jaguar-xj8--gearbox-default-appear-on-dashboard/2000-jaguar-xj8-timing-chain-replacement-vt218070.html">http://www.2carpros.com/forum/2002-jaguar-xj8--gearbox-default-appear-on-dashboard/2000-jaguar-xj8-timing-chain-replacement-vt218070.html</a><br /> <table id="table14" style="BORDER-RIGHT: #000000 1px dashed; BORDER-TOP: #000000 1px dashed; BORDER-LEFT: #000000 1px dashed; BORDER-BOTTOM: #000000 1px dashed" bordercolordark="#000000" width="100%" bordercolorlight="#000000" border="0"> <tbody> <tr> <td style="BORDER-TOP-WIDTH: 1px" width="700"></td></tr> <tr> <td style="BORDER-TOP-WIDTH: 1px" width="700"><span class="name" roundtrip="0" lastvisited="3">By <a name="755408"></a><b roundtrip="0" lastvisited="0">Dave H</b>,<b> </b></span><span class="postdetails" roundtrip="0" lastvisited="0">Certified ASE Technician</span></td></tr> <tr> <td style="BORDER-TOP-WIDTH: 1px" width="100%" roundtrip="0" lastvisited="6"></td></tr> <tr> <td style="BORDER-TOP-WIDTH: 1px" width="700"></td></tr> <tr> <td style="BORDER-LEFT-WIDTH: 1px; BORDER-BOTTOM-WIDTH: 1px; BORDER-RIGHT-WIDTH: 1px"> </td> </tr> <tr> <td colspan="2"> <span class="postbody" roundtrip="0" lastvisited="77">PRIMARY TIMING CHAINS (NON-SUPERCHARGED) <br />NOTE:The 4.0L V8 has no engine timing alignment marks on the crankshaft or camshafts. Engine timing is achieved by installing the Crankshaft Setting Peg (303-531) and Camshaft Locking Tool (303-530). With the crankshaft setting peg in position, ensure the timing flat on each camshaft is in the uppermost position before installing camshaft locking tool. Variable camshaft timing unit may also be referred to as Variable Valve Timing (VVT) unit. <br /><br />NOTE:Special Tools Required: Crankshaft Setting Peg (303-531), Camshaft Locking Tool (303-530), Chain Tensioning Tool (303-532), Primary Chain Wedge (303-533) and Variable Camshaft Timing Oil Control Unit Setting Tool (303-654). See Fig. 232-Fig. 236 . <br /><br />NOTE:"A" bank refers to the right/passenger side of the vehicle and "B" bank refers to left/driver side of the vehicle. <br /><br />NOTE:Each door glass automatically drops 12 mm when the door is opened or when the convertible top is raised or lowered. It is important that windows are lowered before battery is disconnected to allow doors to shut properly. <br /><br />Removal ("A" Bank) <br />Tips Click a link to view tip <br />Tech1Tip: special tool <br /><br /><br />Remove timing cover. See TIMING CHAIN COVER (NON-SUPERCHARGED). <br />Remove the variable camshaft timing oil control solenoid. </span><br /> <span class="postbody" roundtrip="0" lastvisited="77">Remove the variable camshaft timing oil control unit housing retaining bolts and remove the variable camshaft timing oil control unit housing. </span><br /> <span class="postbody" roundtrip="0" lastvisited="77">Remove and discard the variable camshaft timing oil control unit housing "O" rings. <br />Raise and support vehicle. Remove the bolt which secures the Crankshaft Position (CKP) sensor to the flywheel housing. Remove the CKP sensor and allow it to hang free under the engine. Remove the torque converter bolts access grommet from the flywheel housing. </span><br /> <span class="postbody" roundtrip="0" lastvisited="77">Install the crankshaft damper bolt (old one) to the crankshaft, hand-tight only. Rotate crankshaft until the triangular arrow indent on the flywheel is visible through the access hole. See Fig. 144. Confirm that the timing flat on each camshaft is uppermost position. <br />Position the crankshaft so that the Crankshaft Setting Peg (303-531) engages fully into the timing slot. Install and tighten the bolt to secure the crankshaft setting peg. See Fig. 145. Remove the crankshaft damper bolt from the crankshaft and lower the vehicle. <br />Install the Camshaft Locking Tool (303-530) to the "A" bank camshafts, aligning the shafts slightly as necessary. Loosen the bolt that secures the exhaust camshaft sprocket and the bolt that secures the variable camshaft timing oil control unit. See Fig. 146. Remove camshaft locking tool. <br />Remove the primary chain tensioner bolts, primary chain tensioner and tensioner backing plate. See Fig. 147. <br />Remove the primary timing chain tensioner pivot bolt and remove the primary timing chain tensioner blade. See Fig. 148. <br />Remove the bolt which secures the primary timing chain guide. Noting the position of the primary timing chain guide, remove the primary timing chain guide from the upper retaining pin. See Fig. 149. <br />Remove the primary timing chain from the variable camshaft timing oil control unit and from the crankshaft sprocket. Clean and inspect all components. <br />Installation <br />If "B" bank timing chain was removed, see INSTALLATION. If not, go to next step. <br />If previously removed, install the timing chain sprocket to the crankshaft. The teeth of the "A" bank and the "B" bank timing chain sprockets on the crankshaft must be out of phase with each other. If they are in phase after installing, remove the sprocket, turn it on its vertical axis and reinstall sprocket. See Fig. 150. <br />Install the chain tensioning tool to the exhaust camshaft sprocket. Reposition the sprocket (and the variable camshaft timing oil control unit) for the most advantageous position for use of the tool. See Fig. 151. Remove the tool. <br />Install the primary timing chain into position over the crankshaft sprocket and the variable camshaft timing oil control unit. There must be no slack on the drive side of the primary timing chain and the sprockets must not be rotated on the camshafts, or the tensioning tool may not fit. See Fig. 152. <br />Install the primary timing chain tensioner blade to the cylinder block. See Fig. 148. Install the pivot bolt and tighten specification. See TORQUE SPECIFICATIONS. <br />Push the primary timing chain tensioner piston into the tensioner body to provide clearance for installing the primary timing chain. Insert a thin rigid wire through the hole in the end of the tensioner piston to displace the ball from the non-return valve seat. See Fig. 153. With the wire in position, press the piston fully into the tensioner body. Remove the wire. <br />Install the 2 primary timing chain tensioner bolts to the primary timing chain tensioner and locate the tensioner backing-plate on to the 2 bolts. Align and install the primary timing chain tensioner to the cylinder block and to the mating slot on the rear face of the primary timing chain tensioner blade. See Fig. 147. Tighten the primary timing chain tensioner bolts to specification. See TORQUE SPECIFICATIONS. <br />Use a Primary Chain Wedge (303-533), or 2 if needed, between the primary timing chain tensioner and primary timing chain tensioner blade, to take up the slack in the chain for tightening of the variable camshaft timing control unit and exhaust camshaft sprocket. See Fig. 154. <br />Using the chain tensioning tool, apply force to the tool in an counterclockwise direction to tension the chain on its drive side. See Fig. 151. While applying opposing force to the sprocket and chain, tighten the exhaust camshaft sprocket bolt to specification. See TORQUE SPECIFICATIONS. <br />Using the Variable Camshaft Timing Oil Control Unit Setting Tool (303-654), rotate the variable camshaft timing oil control unit fully counterclockwise to the fully retarded position. See Fig. 155. <br />Check that the primary chain wedges are still in place. While applying opposing force to the sprocket and chain using the chain tensioning tool, tighten the variable camshaft timing oil control unit bolt to specification. See TORQUE SPECIFICATIONS. Remove the chain tensioning tool and the primary chain wedges and camshaft locking tool. <br />Raise and support vehicle. Remove crankshaft setting peg. Install the CKP sensor and bolt to the flywheel housing. See Fig. 143. Tighten the CKP sensor bolt to specification. See TORQUE SPECIFICATIONS. Install the access grommet to the housing and lower the vehicle. <br />WARNING:Check that the ring dowels are engaged squarely. Fully locate the assembly as much as possible by hand. Failure to follow this procedure may result in damage to the vehicle. <br /><br />Install NEW "O" rings to the variable camshaft timing oil control unit housing. Lubricate the "O" rings and the bushing. Install the variable camshaft timing oil control unit housing. See Fig. 142. Install the variable camshaft timing oil control unit housing bolts. Tighten to specification. See TORQUE SPECIFICATIONS. <br />Install the variable camshaft timing oil control solenoid. See Fig. 141. Install and tighten the variable camshaft timing oil control solenoid bolt to specification. See TORQUE SPECIFICATIONS. <br />Install the timing chain cover. See TIMING CHAIN COVER (NON-SUPERCHARGED). </span><br /></td></tr></tbody></table>

INSTALLATION

1. Using a vise, lightly compress the secondary chain tensioner piston until the piston step is flush with the tensioner body. Using a pin or suitable tool, release ratchet pawl by pulling pawl back against spring force through access hole on side of tensioner. While continuing to hold pawl back, Push ratchet device to approximately 2 mm from the tensioner body. Install Special Tool 8514 lock pin into hole on front of tensioner. Slowly open vise to transfer piston spring force to lock pin (Resetting Secondary Chain Tensioners).
2. Position primary chain tensioner over oil pump and insert bolts into lower two holes on tensioner bracket. Tighten bolts to 28 N·m (250 in. lbs.). CAUTION: Overtightening the tensioner arm torx® bolt can cause severe damage to the cylinder head. Tighten torx® bolt to specified torque only.
   
3. Install right side chain tensioner arm. Apply Mopar® Lock N, Seal to torx® bolt, tighten bolt to 17 N·m (150 in. lbs.). NOTE: The silver bolts retain the guides to the cylinder heads and the black bolts retain the guides to the engine block.
   
4. Install the left side chain guide. Tighten the bolts to 28 N·m (250 in. lbs.). CAUTION: Overtightening the tensioner arm torx® bolt can cause severe damage to the cylinder head. Tighten torx® bolt to specified torque only.
   
5. Install left side chain tensioner arm. Apply Mopar® Lock N, Seal to torx® bolt, tighten bolt to 17 N·m (150 in. lbs.).
6. Install the right side chain guide. Tighten the bolts to 28 N·m (250 in. lbs.).
7. Install both secondary chains onto the idler sprocket. Align two plated links on the secondary chains to be visible through the two lower openings on the idler sprocket (4 o'clock and 8 o'clock). Once the secondary timing chains are installed, position special tool 8515 to hold chains in place for installation (Installing Secondary Timing Chains on Idler Sprocket).
8. Align primary chain double plated links with the timing mark at 12 o'clock on the idler sprocket. Align the primary chain single plated link with the timing mark at 6 o'clock on the crankshaft sprocket (Timing Chain System).
9. Lubricate idler shaft and bushings with clean engine oil.
10. Install all chains, crankshaft sprocket, and idler sprocket as an assembly (Installing Idler Gear, Primary and Secondary Timing Chains). After guiding both secondary chains through the block and cylinder head openings, affix chains with a elastic strap or the equivalent, This will maintain tension on chains to aid in installation. NOTE: It will be necessary to slightly rotate camshafts for sprocket installation.
    
11. Align left camshaft sprocket “L” dot to plated link on chain.
12. Align right camshaft sprocket “R” dot to plated link on chain. CAUTION: Remove excess oil from the camshaft sprocket bolt. Failure to do so can result in over-torque of bolt resulting in bolt failure.
    
13. Remove Special Tool 8515, then attach both sprockets to camshafts. Remove excess oil from bolts, then Install sprocket bolts, but do not tighten at this time.
14. Verify that all plated links are aligned with the marks on all sprockets and the “V8” marks on camshaft sprockets are at the 12 o'clock position (Timing Chain System). CAUTION: Ensure the plate between the left secondary chain tensioner and block is correctly installed.
    
15. Install both secondary chain tensioners. Tighten bolts to 28 N·m (250 in. lbs.). NOTE: Left and right secondary chain tensioners are not common.
    
16. Before installing idler sprocket bolt, lubricate washer with oil, and tighten idler sprocket assembly retaining bolt to 34 N·m (25 ft. lbs.).
17. Remove all locking pins (3) from tensioners. CAUTION: After pulling locking pins out of each tensioner, DO NOT manually extend the tensioner(s) ratchet. Doing so will over tension the chains, resulting in noise and/or high timing chain loads.
    
18. Using Special Tool 6958, Spanner with Adaptor Pins 8346, tighten left (Tightening Left Side Camshaft Sprocket Bolt) and right (Tightening Right Side Camshaft Sprocket Bolt). camshaft sprocket bolts to 122 N·m (90 ft. lbs.).
19. Rotate engine two full revolutions. Verify timing marks are at the follow locations:
    • primary chain idler sprocket dot is at 12 o'clock (Timing Chain System)
    • primary chain crankshaft sprocket dot is at 6 o'clock (Timing Chain System)
    • secondary chain camshaft sprockets “V8” marks are at 12 o'clock (Timing Chain System)
20. Lubricate all three chains with engine oil.
21. After installing all chains, it is recommended that the idler gear end play be checked (Measuring Idler Gear End Play). The end play must be within 0.10–0.25 mm (0.004–0.010 in.). If not within specification, the idler gear must be replaced.
22. Install timing chain cover (Refer to 9 - ENGINE/VALVE TIMING/TIMING BELT / CHAIN COVER(S) - INSTALLATION) and crankshaft damper (Refer to 9 - ENGINE/ENGINE BLOCK/VIBRATION DAMPER - INSTALLATION).
23. Install cylinder head covers (Refer to 9 - ENGINE/CYLINDER HEAD/CYLINDER HEAD COVER(S) - INSTALLATION). NOTE: Before installing threaded plug in right cylinder head, the plug must be coated with sealant to prevent leaks.
    
24. Coat the large threaded access plug with Mopar® Thread Sealant with Teflon, then install into the right cylinder head and tighten to 81 N·m (60 ft. lbs.) (Cylinder Head Access Plug Location).
25. Install the oil fill housing.
26. Install access plug in left cylinder head (Cylinder Head Access Plug Location).
27. Install power steering pump (Refer to 19 - STEERING/PUMP - INSTALLATION).
28. Install radiator fan shroud.
29. Fill cooling system (Refer to 7 - COOLING - STANDARD PROCEDURE).
30. Connect negative cable to battery.

I'm not sure what you may be "doing wrong", but here is the manufacturer procedure for aligning the timing marks.


^Refer to this diagram during step 12.

^Refer to this diagram during step 13.

^Refer to this diagram for step 19.

1. Align crankshaft sprocket timing mark to the mark on oil pump housing. NOTE: Lubricate timing chain and guides with engine oil before installation.
2. Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links.
3. Lower the primary chain with left side sprocket through the left cylinder head opening. NOTE: The camshaft sprockets can be allowed to float on the camshaft hub during installation.
4. Loosely position left side camshaft sprocket over camshaft hub.
5. Align timing (plated) link to the crankshaft sprocket timing mark.
6. Position primary chain onto water pump drive sprocket.
7. Align right camshaft sprocket timing mark to the timing (plated) link on the timing chain and loosely position over camshaft hub.
8. Verify that all chain timing (plated) links are properly aligned to the timing marks on all sprockets.
9. Install left side lower chain guide and tensioner arm. Tighten attaching bolts to 28 Nm (250 in. lbs.). NOTE: Inspect oil ring on chain guide access plug before installing. Replace O-ring as necessary.
10. Install chain guide access plug to left side cylinder head. Tighten plug to 20 Nm (15 ft. lbs.)
11. NOTE: To reset the primary timing chain tensioner, engine oil will first need to be purged from the tensioner.
12. Purge oil from timing chain tensioner using the following procedure:
a) Place the check ball end of tensioner into the shallow end of Special Tool 8186.
b) Using hand pressure, slowly depress tensioner until oil is purged from tensioner.
13. Reset timing chain tensioner using the following procedure:
a) Position cylinder plunger into the deeper end of Special Tool 8186.
b) Apply a downward force until tensioner is reset. NOTE: If oil was not first purged from the tensioner, use slight finger pressure to assist the center arm pin of Special Tool 8186 to unseat the tensioner's check ball. CAUTION: Ensure the tensioner is properly reset. The tensioner body must bottom against the top edge of Special Tool 8186. Failure to properly perform the resetting procedure may cause tensioner jamming.
14. Install the reset chain tensioner into the right cylinder head.
15. Position tensioner retaining plate and tighten bolts to 12 Nm (105 in. lbs.).
16. Starting at the right cylinder bank, insert a 3/8" square drive extension with a breaker bar into intake camshaft drive hub. Rotate camshaft until the camshaft hub aligns to the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and tighten to 28 Nm (250 in. lbs.).
17. Turn the left side camshaft by inserting a 3/8" square drive extension with a breaker bar into intake camshaft drive hub and rotate camshaft until the sprocket attaching bolts can be installed. Tighten sprocket bolts to 28 Nm (250 in. lbs.).
18. Rotate engine slightly clockwise to remove timing chain slack, if necessary.
19. To arm the timing chain tensioner: Use a flat bladed pry tool to gently pry tensioner arm towards the tensioner slightly. Then, release the tensioner arm. Verify the tensioner is armed (extends).
20. Install the timing chain cover, crankshaft damper, and cylinder head covers.
21. Install camshaft position sensor and connect electrical connector.

Hope this helps!
Mitchell

Absolutely NOT TRUE this vehicle has a timing chain, NOT a timing belt. It has a serpentine belt. Thanks for using FIX YA