Door will not unlock believe arm is bent or un latched

you must have either broke a plastic clip at the lock area look good or one of the little arms came off look good you will find hte problem .bothe doors , did you brake a wire ? look good

Buy something called a z-tool or call AAA and have them open the door for you.. A z tool took the place of a slim jim. It will not damage your car though...

pull the door panel off and inspect the door latch. Sounds like you jammed or bent part of it out of place. If the handles are very loose, check and see it the door latch arm popped out of place

This is a lock smith or dealer issue unless you can get a slim jim type tool to reach through the window slot and catch the latch.

the release at the bottom of hatch can be ---rusted normal in northeast --- linkage popped or broken --linkage clip popped or broken --- need to crawl into back and remove the plug [ lower center of rear hatch panel will need a long screw driver and light will see linkage and latch push down on linkage arm and push open hatch when opened you can remove the rear panel and assess the problem but lube the latch and upper window latch

you will need to remove inner door panel, either the handle itself broke where the rod connects,or the rod fell off or broke at the door latch, or the door latch lever bent or corrodded, the outer and inner handles use the same door latch but not the same mechanisms or rods to operate the latch. Once you remove the door panel and the inner dust shield with the window up look in the bottom of door for clips or a rod or broken parts. and note latch and handle for boken or bent and missing pieces. once you start looking it all becomes self explanatory.

Sounds like it won't unlock as the power lock motor may have failed. You need to remove the inside door panel to get to the lingage and disconnect the lock motors linkage and it may unlock and open. If not the latch itself other links may have come off. Work the arms an see if it'll open after that doesn't wrk the stricker bolt can be removed thought the latch and with it unscrewed as far as you can the door can be forced open so you can change the latch.

This is common, the door lock actuator is frozen, when this happens the lock wont move, some of these the actuator is part of the latch, look at the lock linkage for the door lock lever and follow to latch and see if you locate another linkage arm from actuator, remove that arm and then unlock the door , hope this helps.

You likely have a "link rod" that has either broken it's clip, or come unclipped from the lock and handle assembly. It could also be a broken door handle itself. It's very difficult to tell untill you have the door panel off to inspect. First, pull the door panel. Should be one screw in the inside door handle (#2 phillips), and 1 or 2 (can't remember) in the inside of the hand grab (also #2 phillips). To get the door latch and lock assembly off the door panel, after removing the screw push the assembly forward (towards the front of the car) and pull outward lightly on the back of the latch assembly. Once off, you will see two metal link rods with plastic clips on them, one for the door release and one for the lock. To remove the rods from the clips, look for the "open end" of the clip and push it. This will swivel the clip out of the way and the rod will lift out of the hole. About 90 degrees of rotatiojn should be enough, and from what I remember, they will rotate (looking down) counter-clockwide to release the clips After that, it's just door panel trees. If I remember correctly, there are between 8 and 10 of them. Start at the door catch/latch and work your way around. If you have a door panel removal tool, use it. If not, a single, or even better a pair of thin (1 inch wide) putty knives can be used. Flat blade screwdriver is the last resort. Once the door panel is off, check the other ends oif the link rods you just took off. If one isn't connected, bingo. If it is, then remove the door latch from the door frame using a 10mm socket and an extention. I believe there are 3 bolts holding the latch to the door. Check the opperation of the latch off the car using a screwdriver to act as the door striker, and opperate the levers the link rods move by hand. If the latch is bad, replace! the Stick

open door remove trim pieces than remove door panel check the clips on both sides of int door release rod if missing replace if there check release leaver for damage replace if bent