Front Bumper Remove

Remove wheels. Remove fender liners front. Remove three nuts per side from inside fender wells. Remove fog lamp grilles. Remove vertical bolt just inside grilles--pointing up. Remove two screws per side under hood near front of fender. Put milk crate under front bumper. Remove belly pan first. Slide bumper forward onto milk crate, disconnect headlight washer line at quick disconnect if so equipped. Disconnect fog light connectors. Remove bumper.

Lift the front end of the car and support on stands.
Remove the front wheels.
Remove the fowards under-tray.
Remove the forward halves of the front wheel arch liners.
Unscrew the small down-facing Torx screw at each top rear corner of the bumper.
Gently pry inwards the rear end of the U-shaped steel channel that holds the fender and bumper flanges together.
Pull the channel rearwards to disengage the lugs from the diagonal slots at the forward end, and remove the channels.
Disconnect the external air temp sensor in the bottom left air intake.
Disconnect the parking sensors connector at the right rear corner. You need to open the lever lock and pull hard without damaging the wiring.
Open the hood and remove two bolts on top of the bumper, next to the inner headlamp mountings.
Remove two nuts in lower grille - vertically beneath above bolts.
If its your first time, get a friend and pull the bumper forwards very slowly and gently, avoiding scratching the fenders.
The bumper is surprisingly light.

It will take about an hour.

There are some steps that help you to easily remove Front Bumper :
1. Open the hood of your car.
2 . Look under the edge of the front of the car at the end of the bumper.
Pull the plastic shield down out of the way if it doesn't come off completely. Reach behind the bumper at each corner and you should find a bolt holding the corner of the bumper to the car. Remove these bolts. The bumper should come off.
For more details, click here at https://www.drivenbystyle.com/body-kits-aerodynamics/front-bumpers

Yes, the bumper has to come off to remove the headlights.
There will be a number of smaller screws around the outside of the bumper, like in the wheel well and under the car by the splash shield under the engine. All of those will need to be removed. Then you need to remove the turn signal lights in the front bumper with a long phillips screwdriver. Take a flashlight and look inside the bumper through the lower grill at the side of the turn signal housing. You'll see a small hole for the screwdriver. The screw doesn't need to come all the way out to remove the light.
Remove turn signal housing on both sides and look back at the frame crossmember behind the bumper. There are two large bolts on each side holding the bumper on. You'll need some extensions to reach them. Once those are out, you'll be able to tell if you missed any smaller screws/clips. Carefully move the bumper cover out of the way to have access to the headlight mounting points.

If you need to remove the entire front bumper. Remove the 3 Phillips head screws in each inner fender (both sides edge of bumper by wheel). Remove the two 8mm bolts that you now have access to and go straight up (behind the inner fender). Remove the three 10mm bolts along the top of the radiator. Crawl underneath and pull the centers out of the plastic push clips (seven I think). Slide the bumper off.

Hope that helps, thanks for using FixYa.

Front

1. Note the radio security code, then disconnect the negative battery cable.
   
2. Remove the bolt from the lower part of the bumper just in front of the wheel opening, and remove the self-tapping screw from the rear most portion of the bumper at the forward portion of the front wheel well.
   
3. On V6 Odyssey models, perform the following:
   
   • Remove the grille.
     
   • Remove the pins and clips from the lower front of the bumper.
     
4. On 4-cylinder Odyssey models, remove the bolts from the left and right side lower brackets for the bumper at the ends of the lower air intake.
   
5. Pull the ends of the bumper outward.
   
6. Have an assistant help guide the bumper up and away from the vehicle.
   
7. Installation is the reverse of the removal procedure.
   

have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal

1. Raise and support the vehicle.
   

1. Remove the RH and LH front wheel (1007).
   

1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).
   
   
   
   
   

1. Remove the four front fender brace screws.
   
   
   
   
   

1. Remove the two front fender brace nuts.
   

1. Remove the two plastic screws.
   

1. Remove the seven clip buttons located under the front bumper cover (17D957).
   
   
   
   
   

1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
   

1. Remove the four front bumper cover brace bolts.
   
   
   
   
   

1. Remove the front bumper cover from the vehicle.
   
   
   
   
   

1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).
   
   
   
   
2. Remove the eight front bumper bolts.

1. Remove the front bumper from the vehicle.
   

Front Bumper (434230)

Removal
1. Remove the radiator grille.
2. Remove the left-hand front wheel.
3. Detach the fender splash shield from the bumper cover and fender (both sides).
4. Remove the air cleaner intake pipe retaining clip.
5. Detach the air cleaner intake pipe from the air cleaner housing.

1 Rotate the pipe clockwise.

2 Detach the pipe.
6. Detach the bumper cover from the fender and support bracket (both sides).
7. Remove the left-hand side bumper retaining nut.
8. Remove the right-hand side bumper retaining nut.
9. Remove the bumper.

Installation
1. To install, reverse the removal procedure.

The procedure is very involved.It requires the removal of the front bumper fascia fasteners from the center and side of the headlamp to be removed.

1. Remove the front bumper fascia fasteners from the center and side of the headlamp to be removed, full removal of the fascia is not necessary. Refer to Front Bumper Fascia Replacement.
2. Gently pull the fascia forward to allow clearance to remove the headlamp assembly.
3. You will also need to remove some of the fasteners at the front of the inner wheel well.
4. The Front Bumper Fascia is the plastic cover over your front bumper.
   
5. You may also have to remove the plastic cover that is located under the front of the hood over the radiator.It extends to both sides.