Computer display not turning on

This not a DIY job. The display is a computer drive device and even if you knew the problem you can't buy parts to fix it. Check online for facilities that repair the center solid state control touch screen. You must send it out for repair.

Hello, I hope this helps. If no change then you probably have a hardware/ wiring issue and the dvd player may need to come out. Please advise
1. Confirm the DVD RSE system is inoperative. (blank screen) 2. For vehicles with Toyota navigation system: Perform the following procedure to turn OFF the RSE Lock function. A. Press the INFO switch on the navigation unit. B. Press the "Screen Setting" touch button on the navigation display. C. Under the "Rear Lock" option, press the "OFF" touch button and then press "OK" in the upper right part of the display. D. Press the DVD switch on the RSE system (if a DVD is NOT already in the player, insert one) and confirm screen is ON and the system will play DVDs. 3. For vehicles without Toyota navigation system: Perform the following procedure to turn OFF the RSE Lock function. A. Push the Audio Control knob multiple times to cycle through the various options (Bass, Mid, Treble, etc.) until "REAR LOCK" is shown on the screen. B. Turn the Audio Control knob so the display says "OFF" next to "REAR LOCK". C. Press the DVD switch on the RSE (if a DVD is NOT already in the player, insert one) and confirm screen is ON and the system will play DVDs. 4. If the above procedure resolves the concern, explain the system operation to the customer.This procedure is described in the Audio/Video" section of the vehicle Owner's Manual. 5. If the above procedure does NOT resolve the concern, perform RSE diagnosis using the Technical Information System (TIS), 2006 model year applicable vehicle Repair Manual.

• Turn the ignition switch to the On position and ensure that the display screen is in the Trip A mode.
• Turn the ignition switch to the Off position.
• While pressing the TRIP switch button, turn ignition switch On. Hold the TRIP button down through the entire reset procedure.
• The odometer indicates 000000 and then returns back to Trip A.

• Turn the ignition switch to the On position and ensure that the display screen is in the Trip A mode.
• Turn the ignition switch to the Off position.
• While pressing the TRIP switch button, turn ignition switch On. Hold the TRIP button down through the entire reset procedure.
• The odometer indicates 000000 and then returns back to Trip A.

You need to replace the computer for the display. I found one at the local junk yard cost me $30.00 and fixed the problem. It is the display screen computer.

SWITCH IGNITION ON WITH ENGINE OFF.PRESS SMALL ROUND BUTTON ON LOWER RIGHT OF THE SPEEDOMETER UNTIL IT DISPLAY ODOMETER.THEN TURN OFF IGNITION SWITCH OFF.PRESS AND HOLD SAME ROUND BUTTON LOWER RIGHT SPEEDOMETER TURN IGNITION TO ON WITH ENGINE OFF.CONTINUE TO HOLD BUTTON FOR AT LEAST 5 SECONDS UNTIL IT DISPLAY INDICATES 000000 AND MAINT REQUIRED LAMP WILL EXTINGUISH.RESETTING IS COMPLETE.

stereo codes for Honda

Method 1 (all applicable models except '03-07 Accords with the navigation system)
1. Turn the ignition switch to ON (II).
2. Turn on the audio unit, and make sure you see stereo COdE in the display. If you don't see this message, pull the backup fuse for 1 minute, and then go back to step 1.
3. Turn off the audio unit.
4. Press and hold the 1 and 6 preset buttons, then turn on the audio unit. The display toggles between two screens. The first screen displays a U and the first four digits of the serial number (for example, U2200). The second screen displays an L and the last four digits of the serial number (for example, L0055). Ignore the U and L, and write down all eight digits.

Method 2 ('03-07 Accords with the navigation system)
1. Turn the ignition switch to ACC (I).
2. Turn on the audio unit, and make sure you see COdE in the upper display. If you don't see this message, pull the backup fuse for 1 minute, and then go back to step 1.
3. Turn off the audio unit.
4. Press and hold the top halves of the SEEK/SKIP and CH/DISC bars, and then press and release the PWR/VOL knob. This display toggles between two screens. The first screen displays a U and the first four digits of the serial number (for example, U2200). The second screen displays an L and the last four digits of the serial number (for example, L0055). Ignore the U and L, and write down all eight digits.
5. Call Honda Dealer for Radio Code.
6. Use the TUNE knob to enter the first four digits of the anti-theft code into the audio unit. (Ignore the last digit; it's not used.) When you turn the TUNE knob, COdE disappears, and a single digit is displayed. Turn the knob left or right to select each of the anti-theft code digits. When you press the TUNE knob, the system beeps and accepts each digit as it spells out CODE on the display.

https://radio-navicode.honda.com

Method 1 (all applicable models except '03-07 Accords with the navigation system)
1. Turn the ignition switch to ON (II).
2. Turn on the audio unit, and make sure you see COdE in the display. If you don't see this message, pull the backup fuse for 1 minute, and then go back to step 1.
3. Turn off the audio unit.
4. Press and hold the 1 and 6 preset buttons, then turn on the audio unit. The display toggles between two screens:
- The first screen displays a U and the first four digits of the serial number (for example, U2200).
- The second screen displays an L and the last four digits of the serial number (for example, L0055). Ignore the U and L, and write down all eight digits.

Method 2 ('03-07 Accords with the navigation system)
1. Turn the ignition switch to ACC (I).
2. Turn on the audio unit, and make sure you see COdE in the upper display. If you don't see this message, pull the backup fuse for 1 minute, and then go back to step 1.
3. Turn off the audio unit.
4. Press and hold the top halves of the SEEK/SKIP and CH/DISC bars, and then press and release the PWR/VOL knob. This display toggles between two screens. The first screen displays a U and the first four digits of the serial number (for example, U2200). The second screen displays an L and the last four digits of the serial number (for example, L0055). Ignore the U and L, and write down all eight digits.
5. Call Honda Dealer for Radio Code.
6. Use the TUNE knob to enter the first four digits of the anti-theft code into the audio unit. (Ignore the last digit; it's not used.) When you turn the TUNE knob, COdE disappears, and a single digit is displayed. Turn the knob left or right to select each of the anti-theft code digits. When you press the TUNE knob, the system beeps and accepts each digit as it spells out CODE on the display.

If this don't work, definitly you need to call Honda delaer using your VIN.

Hope this help.

Repair Procedure
1. Confirm the customer's complaint of DVD RSE system inoperative.
2. For vehicles with Lexus Navigation System, perform the following procedure to turn OFF the RSE Lock function:
A. Press the INFO button to display the "Information" screen on the navigation unit.
B. Press the "Screen Setting" touch button on the navigation display.
C. Under the "Rear Lock" option, press the "OFF" touch button and then press "OK" in the upper right part of the display.
D. Press the DVD switch on the RSE system, (If a DVD is NOT already in the player, insert one) and confirm screen is "ON" and the system will play DVD's.
3. For vehicles without Lexus Navigation System, perform the procedure to turn "OFF" the RSE Lock function.
A. Push the audio control knob multiple times to cycle through the various options (Bass, Mid, Treble, etc.) until "Rear Lock" is shown on the screen.
B. Turn the audio control knob so the display says "OFF" next to "REAR LOCK".
C. Press the DVD switch on the RSE (if a DVD is NOT already in the player, insert one.) and confirm screen is "ON" and the system will play DVDs.
4. If the above procedure resolves the concern, explain the system operation to the customer. This procedure is described in the "Audio/Video" section of the vehicle owner's manual.let me know lf this helps.