High idle i bought new lines and a tps,map sensor and a iac and at park its idles at 1500 rpm

Stuck throttle plate . gummed up with varnish or a problem with IAC valve . IAC - idle air control valve ! Videos on youtube , how they work how to clean . Idle Air Control Valve Could have unmetered air entering the engine pass the MAF sensor , a bad MAP sensor ! I would check the throttle plate first , if dirty clean it . Then check IAC valve if not the throttle plate . GM Idle Air Control IAC Function Diagnostics and Repair

a bad tps, map sensor, or such- could just be the cold idle sensor

Before buying a ECM for the car I would do a smoke test on the vacuum line to be sure there is no leaks and causing the idle to very. Hope this helps.

I would check the IAC motor or idle air control motor, heres a little info.about the part.Stratus Sedan, 1999-2005 Idle Air Control Motor

• DESCRIPTION & OPERATION
• REMOVAL & INSTALLATION

Print

Description & Operation

Not for Dodge Stratus Sedan
The idle air control motor (IAC) attaches to the throttle body. It is an electric stepper motor. The PCM adjusts engine idle speed through the idle air control motor to compensate for engine load, coolant temperature or barometric pressure changes. The throttle body has an air bypass passage that provides air for the engine during closed throttle idle. The idle air control motor pintle protrudes into the air bypass passage and regulates airflow through it.
The PCM adjusts engine idle speed by moving the IAC motor pintle in and out of the bypass passage. The adjustments are based on inputs the PCM receives. The inputs are from the throttle position sensor, crankshaft position sensor, coolant temperature sensor, MAP sensor, vehicle speed sensor and various switch operations (brake, park/neutral, air conditioning).

Fig.

Not for Dodge Stratus Sedan
When engine rpm is above idle speed, the IAC is used for the following functions:


Off-idle dashpot Deceleration air flow control A/C compressor load control (also opens the passage slightly before the compressor is engaged so that the engine rpm does not dip down when the compressor engages)
The idle air control motor (IAC) attaches to the throttle body. It is an electric stepper motor. The PCM adjusts engine idle speed through the idle air control motor to compensate for engine load, coolant temperature or barometric pressure changes. The throttle body has an air bypass passage that provides air for the engine during closed throttle idle. The idle air control motor pintle protrudes into the air bypass passage and regulates airflow through it.
The PCM adjusts engine idle speed by moving the IAC motor pintle in and out of the bypass passage. The adjustments are based on inputs the PCM receives. The inputs are from the throttle position sensor, crankshaft position sensor, coolant temperature sensor, MAP sensor, vehicle speed sensor and various switch operations (brake, park/neutral, air conditioning).

Fig.

When engine rpm is above idle speed, the IAC is used for the following functions:


Off-idle dashpot Deceleration air flow control A/C compressor load control (also opens the passage slightly before the compressor is engaged so that the engine rpm does not dip down when the compressor engages)
Target Idle
Target idle is determined by the following inputs:


Gear position ECT Sensor Battery voltage Ambient/Battery Temperature Sensor VSS TPS MAP Sensor
Target idle is determined by the following inputs:


Gear position ECT Sensor Battery voltage Ambient/Battery Temperature Sensor VSS TPS MAP Sensor

Removal & Installation

1. Disconnect the negative battery cable.
2. Disconnect the IAC electrical connector.
3. Remove the IAC mounting screws.
4. Remove the IAC.

To Install:

1. Install the IAC to the throttle body.
2. Tighten mounting screws to 5.1 Nm (45 inch lbs.) torque.
3. Attach electrical connector to the IAC.
4. Connect the negative battery cable.
   
   

   Fig.
   

1. Disconnect the negative battery cable.
2. Disconnect the IAC electrical connector.
3. Remove the IAC mounting screws.
4. Remove the IAC.

To Install:

1. Install the IAC to the throttle body.
2. Tighten mounting screws to 5.1 Nm (45 inch lbs.) torque.
3. Attach electrical connector to the IAC.
4. Connect the negative battery cable.

Check your vacuum lines for leaks. Symptoms suggest vacuum leak.

sounds like the idle air is gone

You don't have to try both, but...If you can get a scanner hooked up, you can see the TPS move as you depress the throttle, and verify if it is good or bad. The IAC can also be viewed with a scanner, and they get gummed up, and most can be cleaned.
Also, a bad temperature sensor can cause a high idle if it thinks it's real cold out.
Also, a bad power steering pressure switch can cause a high idle.
All of these can be looked at with a scanner!

Sounds like the tps (throttle position sensor) is either defective, or out of adjustment. Need an oscilloscope to check, so see a mechanic. Could also be vacuum leak. check lines for cracks and leaks

did you replace the iac motor or the tps , iac is the idle air control and the tps is the throttle position sensor

IAC valve problem. Nissan has a updated harness (with one way diode inside of the harness) to prevent backfeeding for the IAC valve and a new IAC valve also gets installed. That's where I would look. IAC valve or "idle air control" valve.