Ford telstar big end torque settings - F Ford Cars & Trucks

The torque settings for the big end (connecting rod) bolts on a 2008 Ford Transit 2.4L diesel engine are as follows:

• Step 1: Torque the bolts to 25 Nm (18 lb-ft) using a torque wrench.
• Step 2: Tighten the bolts an additional 90 degrees (1/4 turn) using a torque angle gauge.
• Step 3: Tighten the bolts another 90 degrees (1/4 turn) using a torque angle gauge.

Note that these torque settings are for the standard size connecting rod bolts. If your engine has oversized or undersized bolts, you will need to consult the manufacturer's specifications for the correct torque settings.
Also, it's important to use a good quality torque wrench and torque angle gauge to ensure that the bolts are tightened to the correct specifications. Over-tightening or under-tightening the bolts can lead to engine damage or failure.

Here are the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends:
Main bearings

• Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm
• Main bearing bolts: 45 Nm + 90°

Head bolts

• Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°
• Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Nm + 180°

Big ends

• Connecting rod cap nuts: 1st stage - 22 Nm, 2nd stage - 40 Nm + 90°

Please note that these are just the general torque settings. The exact torque settings may vary depending on the specific engine and vehicle. It is always best to consult your vehicle's service manual for the correct torque settings.
Here are some additional tips for tightening the torque settings:

• Use a torque wrench to ensure that the bolts are tightened to the correct torque.
• Tighten the bolts in a star pattern, working your way from the center out.
• Do not overtighten the bolts, as this can damage the engine.

All that information is within your service manual.

https://www.google.com/search?q=bolt+torque+settings+for+a+ford+6600+tractor.big+ends.&hl=en&tbm=isch&source=iu&ictx=1&fir=Uer--eKA7AOgkM%253A%252Cnn1pdY4J8nGKcM%252C_&vet=1&usg=AI4_-kTyOrDUmp3sE7RFkCEfqtQpes9kfw&sa=X&ved=2ahUKEwj0nu6KicPpAhUIDxQKHQ7CBJgQ9QEwAXoECAoQBw#imgrc=Uer--eKA7AOgkM:

Main bearings Stage 1 34-38 Nm Main bearings Stage 2 68-76 Nm Big end bearings Stage 1 26-29 Nm Big end bearings Stage 2 53-59 Nm

why don't u try online
some websites deal in it real time.. along with solutions to problems how to repair fix ser vice nd all
reliable-store is pretty good. . they also have live assistance

hi Bonginkosi.
this link should show you some diagrams.
TORQUE SETTINGS FOR MAIN BIG ENDS BEARING FORD IKON 1 6 Google Search

ford /mazda clone
1999 end of the model only sold in japan

ford dropped telstar and went with mondeos


The last Telstar, based on the GF platform, was released in 1997, but was only sold in Japan,


rare repair manual to find
gregoroies haynes or chilton

if the car is out side japan as an import

this is the closest possible one to use

Ford Telstar & Mazda 626 Sedan & Hatch 1987-92 Wagon 1987-97 Repair Manual 2.0 2.2
no free bees or cd types online a
repair manuals are in book form
source from
ebay or other online repair manual sellers

Here are the big end bearing torque settings for Ford Rocam 1.6:
1. 30-degrees
2. 90-degrees
3. 90-degrees

54 to 64 ft. lbs. for the flywheel bolts and you must put thread sealer on the the bolts or you will have an oil leak.