Question about 2008 Hyundai Elantra

1 Answer

Revs on it's own when clutch pushed in

Noticed especially after I hit a certain railroad track bumpy area, that when I push in the clutch to downshift or shift at all, for a good few miles it will rev up to 3s on it's own when I depress the clutch to change gears up or down. It goes into first and second quite fine... especially on a cold start in the morning... but only after it's been running 25 30 min and hitting that bumpy area... then it starts to act up. Is my clutch going out?

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

It sounds like you may have a vacuum leak, or 2
Check all hoses around gearbox and engine to ensure they are all a snug fit and do not appear worn or split. You can check for vacuum leaks by spraying a mist in the direct area and watch to see if it gets sucked in. Move each hose around while at idle to see if the revs change.
Good Luck I hope it helps

Posted on Jun 24, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
mrgreenz
  • 962 Answers

SOURCE: Hyundai accent high revving during gear change

you may have a problem with the idle sensor located near the fuel injection system.

Posted on Oct 29, 2008

jackiaria
  • 350 Answers

SOURCE: 2000 Hyundai Elantra Transmission problem

I don't know if I can help but as an owner of a Hyundai Elantra 2000 GLS with 205,000 miles and the original clutch and transmission I'll try and help!

I always start with the lowest cost solution first and avoid mechanics as much as possible!

Have you checked the trans fluid?
It should be changed every 30,000 miles!
Sometimes a Lucas Trans Fluid will cure - fix slippage!

Have you checked for a clutch adjustmet!
An adjustment can cure - fix slippage!

Are you a clutch rider with your foot always on the clutch?
If so you may have worn out the clutch!

How many miles to you have on your Hyundai Elantra 2000?

Posted on Jan 17, 2009

  • 28 Answers

SOURCE: wont rev past idle

you need to have the fuel pressure checked

Posted on Feb 02, 2009

BritishChick
  • 2 Answers

SOURCE: High rev when starting hyundai atos

Check the vacuum hoses, but sounds like the IAC or even the o2 sensors. The computer will pick up on the o2 sensors but not the IAC..Go to your local ADVANCE store and they will check on computer for free :)

Posted on Jul 26, 2009

  • 1 Answer

SOURCE: 2008 Hyundai Accent problems

I had a similar problem with my 2008 accent, I took it to the dealer a couple times before they noticed the engine had shifted slightly and had to be aligned and tightened down properly. It has stopped the transmision shudders completely.

Posted on Feb 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Nissan Xterra Shaking Problems.HELP?


each one of the cylinders have there own seperate coil, if cylinder 5 is misfiring then the coil is bad. One cylinder not firing will cause the vehicle to run really rough hope this is helpful

Jul 06, 2012 | 2005 Nissan Xterra

1 Answer

95 ford Ranger Splash 3.0L I was driving the


On passenger side, inside of cab there is a fuel inertia switch mounted on the firewall by where feet go. There is a button underneath, push it. This will reset switch. Truck should get fuel now and start. These switches get weak and if passenger kicks it truck will shut down. Will still turn over but not start.

Jul 07, 2010 | 1995 Ford Ranger Supercab

2 Answers

P0302 cylinder 2 misfire detected enginge revs


P0302-Cylinder 2 Misfire Detected How do I track down the problem and fix?

Dec 10, 2009 | 2001 Hyundai Elantra

1 Answer

Car shuts off while driving, push in clutch, car back to life


that sounds like wiring or connection issue.
I would firstly try getting a wiring schematic of the vehicles loom then find all the earth points and start by cleaning those and making sure there is clean and secure earth connections

Mar 23, 2017 | 1995 Volkswagen Cabrio

1 Answer

My 1990 s series blazer wont reverse anymore


rebuuild it or replace it the reverse clutch pack is most likely burned out . do a visual of the fluid removed from the tranny also smell it to see if it smells burned use your senses:-) good luck

Jun 21, 2009 | 1990 Chevrolet S-10 Blazer

1 Answer

When clutch pushed in it makes high pitched squeel


Im a mechanic, i think you will find it will be the clutch release bearing on the clutch fork, when you push the clutch in it will push the fork which will push the clutch release bearing onto the clutch plate which rotating with the engine revs

Mar 23, 2009 | 2000 Jeep Wrangler

2 Answers

2006 Kia Spectra Won't Start


Check for a fuel shutoff switch, they are made to go off in accidents and shut off your fuel and needs the button pushed to reset

Jan 07, 2009 | 2006 Kia Spectra

2 Answers

1998 Honda CRV Clutch Problem


hello with your clutch problem if its a hydraulic clutch i cant help you but if its a cable clutch either your cable has snapped or you might of snapped your clutch fork. common problem in holdens also

Nov 29, 2008 | 1998 Honda CR-V

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

84966 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...