How do i remove interior door panel & trim

Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Joko,
You are not very clear on exactly where the dent is. The area behind the side door is called a "quarter panel". These parts are not easily replaced, as they are a welded, structural member of the car's structure. Replacement requires specialized cutting and welding tools, normally only found in auto body shops. If the dent is not to bad, you could try removing the interior plastic trim panels and pushing outward to remove the dent.
Providing that the paint is not damaged and there is not an actual crease in the quarter panel [commonly referred to as a "pop" dent] I would suggest contacting a DENT WIZARD company. They will come to your house and fix the dent, using specialized tools and skills. Do a Google search for PAINTLESS DENT REPAIR including your geographic location in the search to find local companies who can do this work. It's much cheaper than taking the vehicle to an auto body shop.

Expedition Trim Panel Removal

NOTE The door glass must be completely raised.

1. Remove the window control switch plate.
2. Remove the door handle bezel.
   WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
   
3. Remove the two bolts and three screws, and remove the door trim panel.
4. Remove the finish cover to access the two center screws.
5. Disconnect the electrical connectors.
   
   
   
   

   Fig. Expedition - Trim Panel Screws shown
   

6. Remove the door handle bezel.
7. Use service notch.
   WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
   
8. Remove the two bolts and three screws, and remove the door trim panel.
9. Disconnect the electrical connectors.
   
   
   

   Fig. Navigator - Trim Panel Screws shown
   

10. Position the water shield aside.
11. If equipped, disconnect the lock cylinder rod.
12. Disconnect the exterior door handle actuating rod.
13. Remove the bolts and position the front door latch aside.
14. Disconnect the electrical connectors.
15. Release the interior door handle cable and remove the front door latch.
16. Position the cable cover aside.
17. Release the conduit and the interior door handle cable.
18. Release the locking tab and remove the front door lock actuator.
19. To install, reverse the removal procedure and note the following:
    1. Tighten the door latch screws to 80 inch. lbs. (9 Nm).

This procedure is followed to check and fix door locks.

Hope helps.

Front Door Panel - Town Car - Removal
CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove.

Snap out two door pull strap retaining screw covers. Remove screws.

Remove two screws on front and rear side of front door trim panel.
The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.

NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors.

Disconnect driver seat regulator control processor switch (driver door only) if equipped.
Twist out interior lamp wire assembly and remove the front door trim panel.
Installation

Ensure plastic watershield is secured to door panel.
Position front door trim panel to door. Connect interior lamp wiring.
Position the window regulator control switch housing and connect switch connectors. Install the retaining screws.
Connect driver seat regulator control processor (14C708) (driver door only) if equipped.
Align door lock side to its mating slide on the sheet metal (front doors only).
Snap in front door trim panel. Ensure all retainers fit properly.
Install two retaining screws on front and rear side of front door trim panel .
Install two retaining screws and pull strap covers.

Good luck Remember rated this).

exterior panel is not removable. to access center roller,remove screws & clips from interior door trim panels remove roller cover panel inside door.loosen bolts to adjust roller,remove bolts to replace it.

please rate if this helps. Section 01-05: Trim, Interior 1995 Thunderbird, Cougar Workshop Manual REMOVAL AND INSTALLATION The interior trim component Removal and Installation procedures generally apply to all models. If some of the steps do not apply to the particular models being serviced, proceed to the next step. Trim Panels, Door Removal and Installation

1. CAUTION: Do not pry front door trim panel (23942). Prying on front door trim panel will break the hook retainers.
   Disconnect battery ground cable (14301) .
   

1. Carefully pull front door trim panel finish panel (23712) away from front door trim panel .
   
   
   
   
   

Item Part Number Description 1 23713 Front Door Trim Panel Finish Panel 2 17B676 Outside Rear View Mirror Control 3 14028 Door Lock Switch 4 55928-S55 Screw (5 Req'd) 5 14529 Window Regulator Control Switch 6 23942 Front Door Trim Panel

1. Disconnect wires from front door lock switches (14017), outside rear view mirror controls (17B676) and window regulator control switches (14529) , if equipped; remove front door trim panel finish panel.

1. Remove front door trim panel retaining screw through front door trim panel finish panel opening.
   
   Trim Panels, Door
   
   
   
   
   
   Item Part Number Description 1 20124 Front Door 2 23942 Front Door Trim Panel 3 383356-S100 Nut (2 Req'd Each Side) 4 56903-S58 Screw (2 Req'd Each Side)

1. Remove interior lamp lens cover.

1. Remove screw through interior lamp opening.

1. Slide front door trim panel upward to disengage hooks.

1. Rotate top of front door trim panel away from front door (20125) , and lift bottom hooks from front door.

1. Disconnect window regulator jumper wire (14A630) .

1. Remove front door trim panel.

1. To install, reverse Removal procedure.

Hi there.

The procedure is roughly the same for all mk3 x types.
You need to remove all the screws on the armrest and on the ashtray, then undo all the plastic clips using screwdrivers on the panel.

You find detailed instructions on links below, I quote:

" remove two screws at the bottom of the armrest.
pull out ash tray.
remove screw in the middle of the ash tray holder.
pull up on armrest, it should pop up, then pull it out
start at bottom right of door and start popping out the plastic clips (all the way around the door)
(remove speaker wires)
push up door panel - done"



WikiAnswers - How do you remove a rear door panel in a Jaguar XJ6


Also from manual:

Disconnect vehicle battery ground lead.
Remove the door trim pad veneer panel.
Remove the upper trim pad.
Remove the door armrest.
From inside the door pocket, release the puddle lamp (1 Fig.1) securing quarter turn fastener.
Undo and remove fixing (3 Fig.1), (front door only)
Carefully release lower trim pad fir tree fasteners.
To avoid damage and distortion of the door metal, lift the lower trim pad complete with clip and clip retainer.
Carefully pull the trim pad away from the door panel.
Disconnect the multi-plugs (1 Fig.2) and remove the lamp.
Carefully displace the trim pad (2 Fig.1) from the door retaining clips.
Disconnect the multi-plugs (2 Fig.2) and (3 Fig.2).
Remove the door pocket.
Displace and remove the retaining clips and remove the trim..
Refit in the reverse order of the removal procedure. Check the trim pad retainers for damage before refitting.

Before refitting the lower trim pad, remove the clip retainer from the pad and and reposition retainer to the door.

ndo door handle escutcheon screw and remove escutcheon
Remove the door trim pad veneer panel.
Undo and remove the upper trim pad securing screws.
Remove the chrome strip.
Undo and remove the top channel securing nuts.
Displace and remove the top channel assembly.
Place the trim pad aside (Fig. 1).
Refit in the reverse order of the removal procedure.







Thanks Jaguar XJ6 Interior Lights

I will be grateful if you can rate the solution given.

Many thanks.

G.

Exterior Mirror Removal and Installation
All vehicles

1. NOTE: Left side exterior mirror shown, right side similar.
   Remove the interior door trim panel. For additional information, refer to Section 501-05 .

Front Door Trim Panel Removal and Installation

1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .

1. Remove the inside door handle bezel from the trim panel.

1. Remove the window switch assembly.

1. Disconnect the window switch and power door lock electrical connectors.

1. Remove the upper trim panel screw at the window switch opening.

1. Remove the lower trim panel screws.

1. CAUTION: To avoid damage to the door trim panel, do not pull directly outward for this step.
   Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.

1. Disconnect the power mirror electrical connector.

1. Remove the trim panel.

1. Remove the weather shield.

Vehicles with power, heated or approach lamp equipped exterior mirrors

1. Disconnect the electrical connector.

All vehicles

1. Remove the bolts.

1. Remove the exterior rear view mirror (17682).

Carefully pull front door trim panel finish panel away from front door trim panel.
Disconnect wires from front door lock switches, outside rear view mirror controls and window regulator control switches, if equipped. Remove front door trim panel finish panel.
Remove front door trim panel retaining screw through front door trim panel finish panel opening.
Remove interior lamp lens cover.
Remove screw through interior lamp opening.
Slide front door trim panel upward to disengage hooks.
Rotate top of front door trim panel away from front door and lift bottom hooks from front door.
Disconnect window regulator jumper wire
Remove front door trim panel.