Question about 2008 Volvo S40

1 Answer

Accelerator pedal position sensor circuit

I have 2008 Volvo S40 2,5 5T. Because of the broken timing belt the head was replaced.When I start the car in the dash show SRS air bag need service urgent.i start the car and all is fine 800 rpm but after 5-10 min. the rpm start oscillating from 800 -1100 rpm.I used a code reader and say Throttle /pedal position sensor/switch A B voltage correlation.It`s. anybody can help with that?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volvo Master
  • 4,048 Answers

You need to take it off and on the side there is a hole spray some dw40 or switch cleaner in the hole and shake it about a bit in side the sensor. then drain it out. and leave to dry. should be fine then. give it a few turns before putting back on and then set it back to bottom and refit to the markings on the side of the intake. if there is none make some before removing it.

Posted on Jan 22, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Volvo 850 fault codes

SRS reset

Posted on Aug 24, 2008

  • 19 Answers

SOURCE: "SRS - AIRBAG SERVICE URGENT"...message

If you have SRS and "brake failure" it should be taken to a dealer. a shadetree mechanic will screw more up than he will fix in this case. trust me on this! you will pay a price, but will save you more $ and less headache in the longrun.

Posted on May 09, 2009

bunnydawg
  • 5158 Answers

SOURCE: "SRS-Airbag Service Urgent" Reset procedures

just unhook the battery for about 20 minutes. if you have an anti-theft radio make sure you know the code and how to enter it.

Posted on Sep 10, 2009

  • 204 Answers

SOURCE: i have a volvo v70 d5, an my intercooler has a

Yes, your intercooler is a problem cos it cools down the turbo charger. The turbo is what gives you your extra power, and when it overheats, it loses pressure and thatcauses loss of power.

Posted on Feb 03, 2010

  • 11 Answers

SOURCE: 2002 Volvo S60 2.4T AWD SRS-AIRBAG SERVICE URGENT

you will have to have the SRS system reset at volvo dealer. should be around $85 for reset

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 2010 Chevy impala. Reduced engine power. Service traction control and stability track. and check engine light. Codes are P2138 P2122 P0455


Electronic throttle control !
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit
DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage
DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage
DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit
DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage
DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage
DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

2009 Chevy Silverado P2138 Accelerator Pedal Position


Circuit/System Description
The throttle actuator control (TAC) system uses two accelerator pedal position (APP) sensors to monitor the accelerator pedal position. The APP sensors 1 and 2 are located within the pedal assembly. Each sensor has a 5-volt reference circuit, a low reference circuit, and a signal circuit.
Two processors are also used to monitor the TAC system data. Both processors are located within the engine control module (ECM). Each signal circuit provides both processors with a signal voltage proportional to pedal movement. The processors share and monitor data to verify that the indicated APP calculation is correct.

DTC P0455: Evaporative Emission (EVAP) System Large Leak

The control module tests the evaporative emission (EVAP) system for a large leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP system vacuum level. When the conditions for running are met, the control module commands the EVAP canister purge solenoid valve OPEN and the EVAP vent solenoid valve CLOSED. This allows engine vacuum to enter the EVAP system. At a calibrated time, or vacuum level, the control module commands the EVAP canister purge solenoid valve closed, sealing the system, and monitors the FTP sensor input in order to determine the EVAP system vacuum level. The following table illustrates the relationship between the ON and OFF states, and the OPEN or CLOSED states of the EVAP canister purge and vent solenoid valves.

Nov 03, 2017 | Cars & Trucks

1 Answer

2006 impala 3.5 LT check engine and service traction control? Code: P2138


DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation
Electronic throttle control problem .
The throttle actuator control (TAC) system delivers improved throttle response and greater reliability and eliminates the need for mechanical cable. The TAC system performs the following functions:
• Accelerator pedal position sensing
• Throttle positioning to meet driver and engine demands
• Throttle position sensing
• Internal diagnostics
• Cruise control functions
• Manage TAC electrical power consumption
The TAC system includes the following components:
• The accelerator pedal position (APP) sensors
• The throttle body assembly
• The engine control module (ECM)

Accelerator Pedal Position (APP) Sensor
The accelerator pedal contains 2 individual accelerator pedal position (APP) sensors within the assembly. The APP sensors 1 and 2 are potentiometer type sensors each with 3 circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
The APP sensors are used to determine the pedal angle. The engine control module (ECM) provides each APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensors provide the ECM with signal voltage proportional to the pedal movement. The APP sensor 1 signal voltage at rest position is less than 1 volt and increases to more than 4 volts as the pedal is actuated. The APP sensor 2 signal voltage at rest position is less than 0.6 volt and increases to more than 2 volts as the pedal is actuated.
Search P2138 on youtube ,will show diagnostic steps .

Aug 19, 2017 | Cars & Trucks

1 Answer

2000 volvo s80 turbo code p0121


code p 0121 refers to throttle position (TP) sensor A/accelerator pedal position (APP) sensor A--range/ performance problem===causes ---accelerator cable adjustment--TP/APP sensor ---wiring

Dec 23, 2016 | Volvo Cars & Trucks

1 Answer

2007 Yukon XL - P01121 Throttle/Pedal Position Sensor A Circuit Range/Performance.


P1121 GMC - Throttle Position Sensor Circuit Intermittent High Voltage
This codes has nothing to do with APP - accelerator pedal position sensor . This has to do with the throttle body - TPS throttle position sensor . These have know problems ,the sensor an broken wire at throttle body , an when this happens the cruise control wont work . The throttle works by a DC motor controlled by the PCM - engine computer .

Dec 30, 2015 | Cars & Trucks

2 Answers

2007 chevy tahoe loses power


No messaage of reduced engine power ? Your vehicle has electronic throttle control . Has four position sensors , two are located in the gas pedal ,an two in the throttle body . The PCM uses these sensor to know how much to open the throttle plate ,allowing more air into the engine . How did you read this code an where did you read it's definition at ? This is not a code for your vehicle . Some time cheap code readers get them wrong .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit
DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage
DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage
DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit
DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage
DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage
DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

DTC P1516: Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance
DTC P2101: Throttle Actuator Position Performance
DTC P2119: Throttle Closed Position Performance
DTC P2176: Minimum Throttle Position Not Learned

If one of this position sensors is bad it will throw the PCM into a
Reduced Engine Power Mode
When the ECM detects a condition with the TAC system, the ECM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
• Acceleration limiting--The ECM will continue to use the accelerator pedal for throttle control; however, the vehicle acceleration is limited.
• Limited throttle mode--The ECM will continue to use the accelerator pedal for throttle control; however, the maximum throttle opening is limited.
• Throttle default mode--The ECM will turn off the throttle actuator motor and the throttle will return to the spring loaded default position.
• Forced idle mode--The ECM will perform the following actions:
- Limit engine speed to idle by positioning the throttle position, or by controlling the fuel and spark if the throttle is turned off.
- Ignore the accelerator pedal input.
• Engine shutdown mode--The ECM will disable fuel and de-energize the throttle actuator.


017 Accelerator Pedal Position Sensors
Drive by Wire Function and diagnostics by Wells

Jan 01, 2018 | 2002 Oldsmobile Silhouette

2 Answers

Reduced engine power, service traction control, service stabilitrak


First of all a scan tool is need for this not a code reader, you need to view scan data after you find what code is stored in the PCM. It could have a problem with the powertrain control module, wiring, or the Accelerator Pedal Position (APP) Sensors. Here are a few codes that could set .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit

DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage

DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage

DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

Oct 02, 2012 | 2008 Chevrolet Tahoe LS

1 Answer

Error code p1271 on trailblazer


That trouble code is faulting the accelerator pedal sensor. The APP sensors are located in a TAC module mounted to the accelerator pedal bracket. There are three individual APP sensors within the TAC module. Three separate signal circuits, low reference circuits, and 5v reference circuits are used to determine the accelerator pedal position. The APP sensor signal voltages increase when the accelerator pedal is depressed.

Nov 26, 2011 | 2003 Chevrolet TrailBlazer

2 Answers

I have these codes coming up on my 2005 Dodge Ram. 5.7 liter motor: P0406 P2096 P0137 P2299 Thank you.


code #0406 = egr position sensor circuit high ( stuck egr valve or bad egr sensor most likely sensor )

code #2096 = downstream fuel trim system lean ( see next code )

code #0137 = O2 sensor bank 1 sensor 2 circuit low ( replace rear O2 sensor driver side )

code #2299 = brake peddle position/accelerator pedal position incompatible. ( hav you been power braking this truck? ) ( brake light was on wile accelerator was being pushed )

Mar 17, 2011 | 2005 Dodge Ram

2 Answers

Code p2138


P2138 is Throttle Pedal Position Sensor/ Switch D / E Voltage Correlation. Replace the Throttle Pedal Position Sensor/Switch.Remember to have the set code Cleared from the cars computer, this will turn off the check engine light and reset it. Good Luck and have a good XMASS.

Dec 17, 2010 | 2006 Nissan Altima

2 Answers

Hi nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn


REPLACE YOUR THERMASTA OR THE SENSOR

Jun 01, 2008 | 2008 Volvo S40

Not finding what you are looking for?
Cars & Trucks Logo

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

Marvin
Marvin

Level 3 Expert

84625 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...