Wiring diagram need a free wiring diagram for 02 chevy malibu to install remote start and keyless entry. thanks

Right here 1988 90 Chevrolet Pickup Alarm Remote Starter Keyless Entry Wiring

2007 Chevy Impala Keyless Entry: Keyless Entry Only ...

www.2carpros.com/questions/2007-chevrolet-impala-chevy-keyless-entry

Dec 30, 2010 - CHEVY KEYLESS ENTRY ... 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar. 5. ... Connect the new antenna to the RCDLR antenna module. 11.... The existing antenna is grounded into another wiring harness.

TPMS and key FOB range problems - LS1TECH

ls1tech.com/forums/ls4.../719926-tpms-key-fob-range-problems.html

May 24, 2007 - 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar.

Buick Workshop Manuals > Lucerne V6-3.8L (2007 ...

Unfortunately your 2009 Chevy Malibu key fob does not have any self programming procedures. You have to have a professional program this key fob to your vehicle. I do have a couple money saving tips for you:

1) Purchase your Malibu key fob online at https://www.keylessentryremotefob.com/Chevrolet-Malibu-Remotes-and-Keys-s/3733.htm

2) Call a locksmith for programming. They are usually more affordable and they come to you.

You must take it to the Chevy dealer.

you need to call the nearest chevy dealer with you vin, and get the part number from them, there are 2 numbers on the back of the remote, see if they match what the dealer tells you. Have an automotive locksmith program, should cost about 75.00 to do.

1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.

Thanks for using Fixya - a 4 THUMBS rating is appreciated for answering your FREE question.

I am not sure exactly where to get your info for free, but have another solution. The drivers door holds all you need. The door panel needs to be removed and then reconnect the power door lock switch. Then just locking and unlocking the door will trigger the actuator to move, allowing you to find it and the wires connected to it. Disconnect the wires and plug in a Digital Multi-Meter into the plug on the wire end and hit the lock and the unlock buttons to find which polarity to which wire unlocks the door and to lock it would be in reverse. Then he can wire the keyless entry into the truck via these wires and can use wire-taps which will pop over the wires in the truck and allow him to add the keyless entry w/o cutting wires. :D Have fun

Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the DOOR unlock switch.
While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds , the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters.
Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation

Dealer only If you find a different means let me know

There are no wires you can touch to program key fob's , Dealer only ! Need a factory scan tool !
This procedure will erase all keyless entry transmitters from memory.
Install a scan tool.
Turn ON the ignition with the engine OFF.
With the scan tool, select Body.
Select Remote Control Door Lock Receiver (RCDLR).
Select Module Setup.
Select Program Key Fobs.
Select Invalidate All.
Follow the scan tool on screen instructions.