What is the procedure to expose the car battery

Remove all the screws in the handle and any more that hold the front and back case halves together. Gently separate enough to expose the wires going to the battery. Disconnect the negative wire first to stop any chance of tools touching the positive connection.The battery can be lifted out and replaced.

What on the car? The phone? A laptop ? Cars dont have charge points unless electric cars.clip straight to battery red + black any exposed metal part of car

Reset for the key
10 minutes on, then 5 seconds off. Then start.
Relearn procedure is the same except you do it 3 times.
Have a charger on it for the relearn.

Charging the battery is pretty straightforward. Connect it like yo said. If the battery is no good, it will not accept the charge, no matter how long you leave the charger on it.

gas engine :counter clock wise use penetrating oil let soak lefty loosey Diesel Engines

The 2.2L diesel engine utilizes an exposed crankshaft pulley and a hidden crankshaft timing pulley/damper. The following procedure may be used to remove the exposed crankshaft pulley.

1. Disconnect the negative battery cable.
   

2. Loosen and remove the accessory drive belts.
   

3. Turn the crankshaft pulley to align the timing mark with the engine pointer. This should be done if any further procedures are being performed which might disturb valve timing.
   

4. Remove the retaining bolts, then remove the crankshaft pulley.
   

To install:

1. Align and install the crankshaft pulley.
   

2. Install the retaining bolts, then tighten to 10-17 ft. lbs. (14-23 Nm).
   

3. Install the accessory drive belts, then properly adjust their tension.
   

4. Connect the negative battery cable.
   

You may have to expose the battery terminals due the fact of plastic covers on the newer vehicles. If the battery terminals are already exposed, you will find one terminal with a red wire while the other is black, (usually). The terminal witht the red wire is considered the positive terminal, which will match a plus sign. The red jumper cable must be attached to this terminal, and the other red jumper cable must be attached to the other battery with a red wire. Then, follow suit with the black wire, this is the negative wire, hence the minus sign. This works if you have another vehicle to jump your battery from.

If you are using a battery charger, you will have to connect the reds to reds and the blacks to blacks using the aligator clips at the ends.

Your battery is located in a compartment inside the driver side wheel well. Remove the front tire, then remove the cover panel to expose the battery. This is a 30 minute procedure. I would love to know who the design **** was that came up with this brilliant location.

Best way to charge / safest / is to remove battery from vehicle ...set battery in a open well venilated area / no smoking / with the apporpiate capacity 12 volt charger / read the instructions that come with the charger . Attach red connector of charger to positive post of battery (usually red) attach black connector to battery ground (-) negative side of battery / plug charger into appropiate outlet (120) . Reverese application when battery is fully charged .
Re-install battery in vehicle/ being sure to re-install as removed .
Install black cable to battery (-) negative ...then Hot (red) (+)

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation

1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
   

1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
   

1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
   

1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
   

1. To install reverse Removal procedure.
   

------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panels, Door Front—Town Car
Removal

1. Snap out two door pull strap retaining screw covers. Remove screws.
   

1. Remove three screws on front and rear side and center of front door trim panel (23942).
   

1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
   
   Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
   

1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
   
   Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
   

1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
   

1. Remove the door trim panel.
   

1. Disconnect two electrical connectors.
   

1. Remove nut from outside rear view mirror mounting base.
   

1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
   

1. Remove screw from outside rear view mirror base.
   

1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
   

1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
   

If you open the fuse box in driver's compartment by your left leg, there is a red plug that you can pull that will expose a positive lead.

Put a charger on the lead and ground the other side of the charger to the frame and it will provide power to use the hood latch.

I have seen other people write about using the car charger that fits into the cigarette lighter but I have no personal knowledge. I hope that is helpful.

There is also an emergency release under one of the wheel wells but I never attempted to look for it.