Need engine head torque settings for 2005 nissan sentra 1.8

Here you go, the year is close enough.

What are the Nissan almera 2004 1.6 16v cylinder head ...

Answers https://www.answers.com > What_are_the_Nissan_alm...
Feb 22, 2023 - THE NISSAN ALMERA 2005 1.6 16V CYLINDER HEAD TOURQUE SETTINGS. 1.Tighten 29N.M using the correct sequence. 2.Tighten 50°. 3.Tighten 55°.

..

you need a better mechanic that traces ALL of the possibilities of each code, not just read the code and trow in a part hoping that it's fixed ~ it can be wiring as well, not just plug in a new part as mentioned on the 2nd trouble code to the vehicle speed sensor

P0744 Torque Converter Clutch Circuit Intermittent


P0722 Output Speed Sensor No Signal

the first of the 2 looks to be more intensive to trace and find out the problem & the 0722 is the easier job for an intermediate mechanic to trace the wiring for continuity

Can be found in the Haynes repair manual, available at an auto parts store for appx $25.00.

you can go to any auto parts store and buy a haynes manual for your car. they are based on a complete teardown of vehicle, this manual will tell the torque ratings. for about 25.00 dollars.and much more. have a good day !

1. For 1.8L engines, tighten the bolts in sequence, as follows:
   1. Step 1: Bolts 1-10 to 22 ft. lbs. (29 Nm).
   2. Step 2: Bolts 1-10 to 43 ft. lbs. (59 Nm).
   3. Step 3: Loosen bolts 1-10 completely.
   4. Step 4: Bolts 1-10 to 22 ft. lbs. (29 Nm).
   5. Step 5: Bolts 1-10 plus 50-55 degrees.
   6. Step 5: Bolts 11-14 to 74 inch lbs. (8 Nm).
      
      Fig. Cylinder head torque sequence-1.8L engine
      
      
      Fig. Tighten the valve cover bolts in sequence-1.6L and 1.8L engines
      

Nissan QR 2.5 engine produces a torque of 180 ft·lbf (244 N·m) of torque at 4000 rpm .

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

email me ill send you it via email cant post here too bigg!!

heinrichkemp: The engine in your car is a GA16i
I venture you are asking about the head bolts when you refer to torque settings. The head bolts used on this motor are torque to yield (streach bolts) If you are reusing them, you need to check them to insure they are not stretched beyond limits.
The way you measure the bolt is with a micrometer.
Measuring close to the end where the bolt starts to thread in, about 10-12 threads up, take a reading. Now, go to the other end of the bolt where the threads end and measure about 10 threads in.
There should not be more than a .009 inch difference (.228mm). If there is, discard the bold and get a new one.

You must use a sequence to tighten the bolts, below is the sequence.
11
13 9 3 1 6 8

14 7 5 2 4 10
12 15

torque 11,12,13,14 & 15 to 8.3 Nm (6.1 ft lbs)
Torque the main head bolts by the numbered sequence to
29Nm (22 ft lbs) first pull
64Nm (47 ft lbs) second pull
Loosten all the bolts completely
Tighten the to 29Nm (22 ft lbs) first pull
Tighten bolt # 1 clockwise 85 degrees
Tighten bolts #2- 10 65 degrees
Nissan noted that if you do not have a torque angel meter, you can use a regular torque wrench and torque all the bolts to 69Nm (51 ft lbs)
The valves on this engine have hydraulic lifters, consequently require no adjustment.