04 pontiac montana sliding doors no longer work

Possible problems with DVD player after replacing Cabin Air Filter ...

www.topix.com > Pontiac Montana

Apr 13, 2011 - 2006 Montana. Posted in the Pontiac Montana Forum. Leave a Comment ... I recently had my cabin air filter replaced by Jiffy Lube. After they had ... If not, could the dvd player simply blown a fuse and just needs replacing? It just seems ... 14 Famous Movie One-Liners You've Been Quoting Wrong For Years. DVD Repair
Jan 18, 2010
Replace VCR with DVD player in 2001 Montana
Feb 2, 2009
Chevy Uplander "CD Mech Error"
Aug 29, 2008
Reports: 2004-2006 Chevy Uplander Sliding Door Problems ...
Aug 21, 2007
More results from www.topix.com

Pontiac montana sv6 dvd player removal - YouTube

? 1:18
https://www.youtube.com/watch?v=21TTD0ayThc
Oct 15, 2015 - Uploaded by Joshua Freeman
I recently got this 2005 montana sv6 from my grandoa and thedvd player was jamming up and not working ...Missing: movies

Reseting the power sliding door gm Montana or venture? In: Chevy Venture, Pontiac Montana [Edit categories]
[iframe style="BORDER-BOTTOM: 0px; BORDER-LEFT: 0px; VERTICAL-ALIGN: bottom; BORDER-TOP: 0px; BORDER-RIGHT: 0px" id=google_ads_iframe_/51859126/answ_desktop_question_answered_600x300_alt_0 height=300 marginHeight=0 src="javascript:"[/iframe]
Answer:

It's in the owners manual under power door. I believe you pull the fuse under the hood for 15 sec with the overide switch in the off position. ...(roesterman adds...).My power door was opening all the way then closing immediately. I used this method to reset door and it worked! This started happening after I had some body work done to vehicle..maybe they disconnected battery or something. Delay locking was locking doors before slider was closing too. This left the door unlocked. I haven't tested to see if this has been corrected by reset yet.

2 common possibilities. The plungers and plunger pads on the door and the door jam are corroded. Clean those off with a fine sandpaper, then put a dab of silicone grease on them. Then do the re-set procedure exactly as the steps indicate. If that does not help, then a possible door position sensor or the door control module is bad. A diagnostic using the on/off switch and the open/close switchon the system may indicate a code for door position problem. The door position sensor is part of the door motor/actuator assembly. The control module can be replaced separately. Info from here.

I would check the overhead buttons there are two one opens the door, and the other beside it that shows the van crossed out, disables the electric sliding door feature. try playing with that, Also remember, that vehicle must be in PARK for the electric sliding door to open. Make sure the power lock on that door is working, and check the child safety lock when you have it open by the doors catch. Hope that Helps You.

Verify the wiring harness which passes under plastic step & carpet at front passenger side. This wiring harness goes from the firewall to the pillar on the right side and some have crimped connectors in them to act as junction between two or more wires (ususlly the 12volt feed), which deteriorate with time, especially with Salt & Water. Then the electric sliding door stops working and even driver the electric seat can loose power.

There is a ground not connected or a wire open that is causing it to blow

I went to bulldogsecurity.com and looked up the wiring diagram for this vehcle. However, prior to checking this part, I would check to see if you have a blown fuse. It doesn't hurt and only takes a few minutes. There should be a fuse for that either somewhere on the side of the dash or near the brake pedal area. If not it may be under the hood, but it should be inside the vehicle. You may have multiple fuse boxes. If it has (2) sliding doors it will have a wire for the auto doors in each kick panel (under the plastic trim/molding) when you open the door and look down you will see all of the trim/molding it should snap out or may be held in place with a screw or (2). Once you remove that you should see the wires. It says for the left side it is either light blue or black and the right side is definitely light blue. Trace this wire until you find out where it ends (the motor or switch to control the auto doors) Then test the switch/motor to see if it is bad.

sounds like a fuse went out have u checked ur fuses


Here To Help
Shaun

pull inside molding you will see the cables path replace cable he probably broke it