2004 Lexus RX 330 Logo

Related Topics:

A
Anonymous Posted on Aug 03, 2017

I just purchasd my 2004 RX330 and there are no lights on the shift console and environment control bezels. The radio has been recently replace so I'm thinking, maybe they knoked a wire connector loose. How do I remove the radio panel with minimal damage. My Lexus has 121,846 mile on it and it looks and works like a totally new luxury vehicle. I'm so lucky. Thanks for you help.

5 Related Answers

240cpa

  • 548 Answers
  • Posted on Jan 23, 2009

SOURCE: RX 330 - Replace tail light on 2004 Lexus RX330

on the backside of the light there should be a plastic access panel that you can gently pull off with a small flat-bladed screwdriver and then get to the light bulbs. if not, look for a small recess on the side of the lens cover itself.

Ad

Anonymous

  • 290 Answers
  • Posted on Mar 23, 2009

SOURCE: The Lexus car remote key control model ES300

try this:

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (DO NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Anonymous

  • 185 Answers
  • Posted on Oct 03, 2009

SOURCE: Removing the Radio for Lexus Rx300

take the woodgrain cover off around shifter, it pops off. next pull out the small panel just below the radio, pull it straight out towards you, set it aside. there are 4 bolts holding the radio in, you will need a light to see the back 2. remove these bolts and carefully pull radio straight out.

Anonymous

  • 51 Answers
  • Posted on Oct 08, 2009

SOURCE: How to replace Lexus RX330 headlights.

replacing the headlights is easy. There is no need to adjust the afs, is is automatically done within the vehicle. Changing the bulbs doesn't affect the afs system at all.

Anonymous

  • 430 Answers
  • Posted on Nov 23, 2009

SOURCE: 2004 lexus rx330 what does vsc light indicate

VSC is Vehicle Stability Control. This is and electronic sensing which monitors and combines performance of braking, wheel slippage and handling, ect.
If this light comes on along with check engine light, it can be caused by a loose gas cap or faulty o2 sensor.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2009 buick lacrosse console gear indicator bulb

Transmission Floor Shift Control Indicator Lamp Replacement

Remove the front floor console. Refer to Front Floor Console Replacement.
Rotate the floor shift control indicator lamp socket (2). Pull the socket from the trim bezel.
Remove the bulb from the socket.

Front Floor Console Replacement

Preliminary Procedures
Remove the rear floor console. Refer to Rear Floor Console Replacement.
Remove the instrument panel lower trim plate. Refer to Instrument Panel Lower Trim Plate Replacement.
Set the parking brake, then shift the transmission into drive and push the shift indicator down until it locks, to allow clearance to remove the console.
1
Front Floor Console Screw (Qty: 2)
Caution: Refer to Fastener Caution in the Preface section.
Tighten
2 N·m (18 lb in)
2
Front Floor Console Bolt (Qty: 2)
Tighten
10 N·m (88 lb in)
3
Front Floor Console Assembly
4
Front Floor Console Retainer Clip (Qty: 2)
0helpful
1answer

How to replace a/c blower switches 2000 Silverado truck

First step is to apply parking brake to keep vehicle from moving. Remove bezel surrounding gauge cluster, radio, temp control by setting tilt steering to lowest position. With key in ignition, turn key to on position (but do not turn vehicle on). Put gear shift lever to D, L2 or L3 (enough to get shifter out of way when bezel is removed). On far bottom right of bezel, you should be able to get a grip on corner of bezel with your finger, lightly pull on corner. Bezel is held in with tabs. Pull bezel until loose/removed. Temp controller is held in by 2 or 3 screws (7mm). Then just unplug controller. Just follow reverse steps for installation. Good luck.
0helpful
1answer

On my ford freestyle gear indicator light how change it

Remove the PRNDL trim ring.
Remove the upper console panel.
Slide the lower shift knob bezel downward.
  1. Remove the bolt and lift up on the shift knob to remove.
Remove the lower shift knob bezel.
Disconnect the light bulb from the PRNDL bezel. an replace .

26002487-w0jffanovav232xjqcbliw5g-1-0.gif Don't think you need take shifter knob off . Just PRNDL trim plate an upper console plate . They should just pull up , use plastic trim tool to get it so you can get your fingers under an pull up carefully .

26002487-w0jffanovav232xjqcbliw5g-1-2.gif PRNDL trim plate

26002487-w0jffanovav232xjqcbliw5g-1-5.gif Light blub connector !

26002487-w0jffanovav232xjqcbliw5g-1-9.gif
1helpful
1answer

How do I remove radio center console for 2004 Acura TSX

Could be a bent clip. It has to come off. Get as close as you can to the top clip and pull it loose. You don't want o break the bezel, so one of two things will happen. The clip will bend and come out, or the plastic tab holding the clip will break. Neither is that bad. it will still hold close with the other clips. Breaking the bezel is far worse.
0helpful
1answer

How do I remove the center console of a Isuzu Ascender

why not read on alldata.com, its all there,
remove a screw?


25402002-5afre3fjdbg1gkzo1rpx5eib-3-0.jpg
  1. Block the wheels to prevent the vehicle from moving.
  2. Remove the rubber ash tray inserts and rubber mat from the console.
  3. Remove the floor shift control knob. Refer to Floor Shift Control Knob Replacement.
  4. Remove the center console shift lever bezel, Buick only. Refer to Console Shift Lever Bezel Replacement (Refer To List 1).
  5. Remove the console storage compartment. Refer to Front Floor Console Compartment Replacement.
  6. Remove the center console retaining screws.
  7. Adjust the parking brake to the full-up, or fully engaged position.
  8. Release the 2 forward trim extensions ears attached to the lower instrument panel (I/P), Buick only.
  9. Slide the console rearward and raise the rear of the console in order to expose the electrical connectors.
  10. Disconnect the electrical connectors, as necessary.
  11. Adjust the parking brake to approximately the halfway position.
  12. Remove the center console from the vehicle.
  13. If replacing the floor console base, remove the following and retain for transfer:
    • 13.1.
      Remove the HVAC control module (if equipped).
    • 13.2.
      Remove the armrest.
    • 13.3.
      Remove the HVAC module and duct assembly.
    • 13.4.
      Remove the cupholder.
    • 13.5.
      Remove the HVAC upper duct.
or read the FSM (buy one) factory service manual, its all there every step and photos too, (all cars. are like that)
or
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

log in, and see that. and more.
0helpful
1answer

How do I change the middle tail light bulb on a lexus rx330 2004?

Remove the top bezel of the gate. It pops/prys off. Then you will see how to remove the socket(twists out) the remove the bulb/s
0helpful
1answer

I just read you post on replacing the heat controls on my 1998 Ford Contour. Thanks for the good reply. A few more questions on that, Can I replace only the selector switch DEFROST/AC/FLOOR/PANEL? Do I...

SECTION 412-04: Control Components 1998 Contour/Mystique Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 09/14/2001 Climate Control Assembly Removal
  1. Remove the radio chassis. For additional information, refer to Section 415-01.
Audio Unit
Special Tool(s) st1445a.jpg Remover, Radio
415-001 (T87P-19061-A)
Removal
  1. NOTE: Make sure the audio unit key code is available before disconnecting the audio unit electrical connectors and note the audio unit station presets.
    Using the special tool, detach the audio unit.
    • Insert the Radio removal tool into the locating holes until they click into place.
    1. Pull the tools gently to the left and right of the audio unit to release the locking tangs.
    1. Pull the audio unit out of the instrument panel.
    v3801098.jpg
  1. Remove the audio unit.
    1. Disconnect the power electrical connector.
    1. Disconnect the audioline/speaker electrical connector.
    1. Disconnect the antenna cable.
    v3801097.jpg
Installation
  1. NOTE: When installing the audio unit make sure the rear support engages on the carrier.
    To install, reverse the removal procedure.
    • Enter the audio unit keycode and re-program the pre-set audio unit stations
  1. Remove the floor console. For additional information, refer to Section 501-12.
Floor Console - Vehicles with Automatic Transaxle Removal
  1. ani_caut.gif WARNING: Wait at least one minute after disconnecting the battery cables before removing the floor console. Failure to follow this instruction may increase the possibility of accidentally deploying the air bag(s) and may cause personal injury.
    Disconnect the battery ground cable.
    • Wait one minute.
  1. NOTE: Contour shown, SVT similar.
    Remove the rear floor console screws.
    • Move seat fully forward.
    v4301059.jpg
  1. Fully apply the parking brake.
  1. Detach the shift indicator selector bezel.
    gr2486a.jpg
  1. Detach the shift bezel from the selector housing.
    1. Remove three bolts.
    1. Detach shift bezel from the console.
    e0008805.jpg
  1. NOTE: The rear floor console must be raised to disengage the front retaining clips.
    Raise and remove the rear floor console.
    gr2485a.jpg
  1. Remove the four front floor console retaining screws.
    v4301062.jpg
  1. Detach the front floor console.
    1. Set the gearshift lever into position 1.
      Partially remove the front floor console.
    gr2484a.jpg
  1. Disconnect the cigar lighter electrical connections and remove the front center console.
    gr2483a.jpg
  1. Remove the control opening finish panel.
    1. Remove the four screws.
    1. Disconnect the headlamp dimmer switch electrical connector.
    1. Remove the panel.
    gr2522a.jpg
  1. Remove the climate control assembly screws.
    gr2523a.jpg
  1. Remove the climate control assembly.
    • Disconnect the electrical connectors
    • Disconnect the vacuum harness connector.
    gr2536a.jpg
    ------------------------
3helpful
1answer

2004 saturn vue my hazard light button pushed in to dash how to fix

you must pull up the center console trim around the shifter,,,,then remove the screw holding the little tray under the bezel and remove the tray,then pull hard on the trim aroung the radio and vent and it will pull out,then disconnect all the wires for the hvac and so forth and then remove the whole trim from the car flip it over and unscrew the 4 way bezel and replace it with a new onw,2 screws,think like $16 for the bezel then reassemble,common vue issue,dealer stocks parts, about 20 minute job if youre good
2helpful
1answer

I need to replace the cigarette lighter unit and don't know how to take the dash apart

turn ignition switch to on ,shift trans into neutral,i'm assuming this is a baja,remove 2 screws under lid of center console cover lift this piece out of the way now remove bezel surrounding shifter,remove ashtray,above ashtray are 2 screws holding ashtray frame in place remove those now bezel surrounding radio can be removed and now you can remove cigar lighter good luck
8helpful
2answers

04 Navigator gear shift button broken

I only have 2003 Nav procedure. Maybe get used part at car-part.com. Page with * is lowest price.

SECTION 307-05: Automatic Transaxle/Transmission External Controls 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Selector Lever —Floor Shift Removal and Installation
  1. Lift the floor shift PRNDL bezel.
  1. Disconnect the PRNDL bezel wire harness connector.
  1. Remove the shift lever handle and cover.
    1. Slide the handle bezel down.
    1. Remove the screw.
    1. Disconnect the TCS wire harness.
    1. Lift assembly from the shifter lever.
b038436.gif
  1. Position the window regulator control panel aside.
  1. Remove the screws and the console finish panel.
  1. Remove the left side console access panel.
  1. Disconnect the transmission shift cable from the transmission selector arm.
  1. Remove the transmission shift cable retaining clip from the floor shift mechanism through the console access.
  1. Remove the four bolts retaining the floor shift mechanism to the floor.
  1. Disconnect the floor shift mechanism wire harness connector.
  1. Remove the floor shift mechanism from the console.
  1. Remove the brake shift interlock actuator, parking brake release mechanism and harness.
    • Remove the wire harness retainers.
    • Remove the wire harness retainers.
    • Remove the two screws retaining the brake shift interlock assembly.
    • Remove the two screws retaining the parking brake controller.
Not finding what you are looking for?

297 views

Ask a Question

Usually answered in minutes!

Top Lexus Experts

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

926 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...