Need to know

OKAY STANDING IN FRONT OF ENGINE ON LEFT SIDE CYLINDERS FACING YOU IS 1 3 5 ON RIGHT SIDE DRIVER SIDE CYLINDERS FACING YOU IS 2 4 6 LOOKING AT DISTRIBUTOR CAP NUMBER 1 SPARK PLUG ON CAP IN THE 9 OCLOCK POSITION YOUR NUMBER 5 SPARK PLUG ON DISTRIBUTOR CAP IN 6 OCLOCK POSITION .STARTING AT NUMBER 1 SPARK PLUG ON CAP COUNTING CLOCKWISE COUNTING 1 2 3 4 5 6 THATS YOUR SPARK PLUGS WIRES ON CAP TO ENGINE PLUGS. 6 PLUG WIRE ON CAP IS AT 7 OCLOCK POSITION.

Firing order is 1-2-3-4-5-6..Cylinders are 1-3-5 Front to back on the LEFT SIDE and 2-4-6 Front to back on the RIGHT SIDE, as your standing at the fan looking at the transmission. Here is a picture:

number one piston it the first cylinder at the frount of the engine block,,,,,allways! on any engine,,,

do not have a diagram, but heres the firing order. 1-2-3-4-5-6, 1-3-5 is in back, # 1 is closest to alternator. from left to right, or facing engine from front 2-4-6 is in front. 5-2-3-6-4-1 is coil pack, from left to right (facing from front of engine).

Hope this is helpful.

Hi: To Install the Distributor Correctly, 1st thing to do is Remove your #1 Spark Plug assuming it will turn over have someone Turn the Key Off and On in Short Intervals.Either put a Compression Gauge in the #1 Spark Plug HoleOr the Old Fashion Way Works as well just put your Finger in the #1 Plug Hole.As your Helper Cranks the Engine On -Off On -Off.Not A Continuous Crank.When You Feel Air Pressure or See gauge Come up.TYhats when your Engine is a The compression Stroke.Now you Can Drop the New Distributor in its Hole.NOTE: You'll need a Spark Plug and Timing Diagram to See the Position your Distributor ROTOR Line it up to where the Diagram Shows your #1 Spark Plug Wire Will go in the Distributor Cap.If the Distributor Rotor is Not n That Position Your goning to Get Either Back Firing engine May Not Even Stsrt, To This Is Crucial. After The Know that you have The Distributor Droppped The Right position you'll need to Put Gap your Plugs at the Correct Specs, With All Plugs in Now You'll need to Put New Plug Wires on .And They MUST be in the correct order.Sitting inside your Vehicle #1 Plug is the Front Plug on the Drivers Side Next is #3 plug Next is #5 and Your Back Plug is Number 7,On the other side Passenger Front Plug is #2 next #4 Next is #6 and the Back is #8 Assuming you know have your Distributor Dropped in The Proper Position, Put the #1 Spark Plug Wire on the Front Spark Plug (Drivers Side) The Spark Plug Firing Order in Your Engine is 1-8-4-3-6-5-7-2 Clockwise So the Next hole after you have #1 Plug and Wire on And Distributor In Correct Position on COMPRESSION STOKE, Going Clockwise you next wire will be your #8 Position in The Cap And it wil go to the Back Spark Plug on The Rear Spark Plug on Passenger Side. NOTE: Drivers Side Spark Plugs on the Drivers Side Front to Back are Your Odd Numbers 1-3-5-7 Pasenger Side is Your Even Numbers From The Front is #2-4-6-8 Is The Rear PLug .

Heres a Diagram of your Spark plug Positions

Front of Engine
1 2
3 4
5 6
7 8

Hope This Will Get You Going. Let me know The Quality of Help and Solution I've Given You By Voting on It.And May Can Also Send a Testamony
From d_hubbs

For the 3.0L V6:
Firing Order:
1-2-3-4-5-6
Cylinders:
.....(back)
1.......3......5
2.......4......6
....(front)
Distributor:
...(back)
4....5....6
o....o....o
/////////////
\\\\\\\\\\\\\
o....o....o
3....2....1
..(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Standing at front of truck, looking under the hood.

The closest cylinder to you on your right is #1. #2 is close left. #3 is middle right, #4 middle left. #5 is back right and #6 is back left.

Firing order is 1-6-5-4-3-2. This is the sequence for placing the wires on distributor cap in a clockwise direction. #1 spot on cap is the 3rd post after the wiring harness (clockwise). This post should be closest to cylinder #5.

Since you didn't state whether it is a V6 or V8, I'll give you both.

V6 -4.3Liter
Firing Order is 1-6-5-4-3-2
Distributor rotor turns Clockwise
Number 1 spark plug tower on distributor cap, faces the front of the engine.

->Drivers side, spark plug order in engine, starting from the Front going back:
1-3-5
->Passenger side, spark plug order in engine,
starting from the Front going back:
2-4-6

If it's Electronic, the distributor cap has a Left side, (Drivers side), and a Right side, (Passenger side)
Starting from the Front, going back on the Left side,
3-1-5
Starting from the Front going back on the Right side,
2-4-6

V8-5.0, 5.7, and 7.4Liter
Firing Order is 1-8-4-3-6-5-7-2
Distributor rotor turns Clockwise
Number 1 spark plug tower on distributor cap,
faces Front, towards the Drivers side.

Electronic distributor cap has two sides. Drivers, (Left), side and Passenger, (Right), side.
Starting from Front going back on Drivers side,
1-7-3-5
Starting from Front going back on Passenger side,
8-2-4-6

Spark plug order in engine, starting from Front going back, Drivers side:
1-3-5-7
Spark plug order in engine, starting from Front going back, Passenger side:
2-4-6-8

go to the link below for diagram, the white spot on the distributor cap is number one cylinder, wires go in clockwise rotation around the cap.
http://autorepair.about.com/library/firing_orders/bl-fo-9696.htm