Ignition switch tumbler

To replace the ignition tumbler in a 1975 Dodge Sportsman RV, you will need to follow these steps:

1. Remove the steering column cover: Start by removing the screws or bolts that hold the steering column cover in place. Once the cover is removed, you should be able to access the ignition switch and tumbler.
2. Disconnect the electrical connections: There should be two electrical connections that attach to the ignition switch. Disconnect these before attempting to remove the tumbler.
3. Remove the retaining screw: Use a screwdriver to remove the retaining screw that holds the tumbler in place.
4. Remove the tumbler: After removing the screw, the tumbler should slide out of the ignition switch.
5. Install the new tumbler: Insert the new tumbler into the ignition switch, making sure it is securely in place.
6. Reinstall the retaining screw: Use the screwdriver to reinstall the retaining screw.
7. Reconnect the electrical connections: Reconnect the two electrical connections that you disconnected in step 2.
8. Replace the steering column cover: Once everything is back in place, replace the steering column cover and secure it with the screws or bolts.
9. Test the new tumbler: Finally, test the new tumbler to make sure it is working properly and that the RV starts and runs smoothly.

I suggest a locksmith be called in to remove the barrel
he will be able to supply a new barrel and cut the key to suit what you have and set the tumblers to the new key

IF you have a locksmith take it out it is possible that he may be able to repair the pins in the tumbler but I think the cost would be more than getting a new tumbler. If you use a locksmith then he can set the new tumbler pins so that you can use the old key and that will save you carrying extra keys unnecessarily.

If your key will not turn at all there is a good chance that your ignition tumbler has gone bad. The tumbler is the part that your key actually goes into. The tumbler is fairly easy to remove, and the new tumbler will actually come with step by step instructions. A new lock tumbler will normally cost no more then $30. If that does not work the only other option is the ignition switch itself and those are more expensive costing on average around $150 or more. I hope this helps you out, and if you have any more questions please feel free to ask.

Ignition switch located half way down steering column.
Ignition tumbler (Where you insert the key) Need to remove steering wheel, if tilt steering need remove c clip, then there is a hex bolt securing the tumbler.
Ignition switch is a bit more involved. hope this helps, James Booth

lets start simple.get a can of silacone spray oil and spray into the switch and keep moving key and you will find this will reliese the key,if you need to remove the ign switch dont panic as its a simple enough job.Forget about steering wheel and whatever,simply remove the outer plastic cover then this exposes the switch at the back of switch is a plug with wires pull it away ,then below the key you should see a tiny screw undo, and make sure the steering lock is not under pressure,ie steering wheel free,when trying to remove switch move steering wheel back/forward and switch should pull out.good luck.adrian,,,,

You can't do it; the Theft System it's integrated to the vehicle control computer ECU/PCM; you need install one INTERFACE to make this work.

Review this Wiring Diagram and this comment: when installing a 791 TRANSPONDER BYPASS System on this vehicle it will be necessary to remove the BOTTOM STEERING COLUMN Cover and IGNITION SWITCH TUMBLER to gan access to the Factory Transponder System around the Ignition Switch. To do so will require that you first look at the bottom of the STEERING COLUMN COVER to identify the screw holes from the IGNITION SWITCH TUMBLER RELEASE PIN HOLE, that is required to remove the Ignition Switch Tumbler, the IGNITION SWITCH RELEASE PIN HOLE is the SMALLEST Hole in the plastic cover in this picture. NOTE *** to remove the IGNITION SWITCH TUMBLER, a TORX #15 Bit on a Screw Driver will work just fine. Incert it up into this hole and press, at the same time, turning the IGNITION SWITCH ON and the Tumbler will pull out at the same time. This Must be done to remove the IGNITION SWITCH TUMBLER so that the BOTTOM Steering Column Cover can be removed to gain access to the TRANSPONDER SYSTEM built around the IGNITION SWITCH.

Also, its possible that you need other details from the Taurus's Owners Manual.

Hope helps.

The end of the lock cylinder usually breaks off.

The tumblers have wore down and won't let the key turn. At this point you need to have the tumbler set replaced.
God Bless You Greg

What you need to do is this:

Remove Steering wheel
Remove big connector under dash, it has a 8mm bolt that is holding it in, this will loosen up the wires in the steering column
Pull out clock spring and let it hang
Get lock plate compressor and remove lock plate, the snap ring is kinda hard to get off
Remove plates and spring behind lock plate
Put turn signal switch to the turn right position
remove three screws holding in turn signal cam
remove key warning buzzer, needle nose pliers and it just pulls out, be gentle
remove screw with a torx head that holds the ignition tumbler in place



remove tumbler

I hope this helps, it took me a while to figure this out