1997 Jeep Wrangler Logo

Related Topics:

Derrick Posted on Dec 17, 2013
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

1997 jeep wrangler

Does it has 2 tension pulleys

1 Answer

Chris

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Cheetah:

An expert who has answered 20 or more questions within one hour.

  • Expert 86 Answers
  • Posted on Nov 06, 2014
 Chris
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

New Friend:

An expert that has 1 follower.

Cheetah:

An expert who has answered 20 or more questions within one hour.

Joined: Jan 14, 2009
Answers
86
Questions
0
Helped
24668
Points
131

It would if there are 2 belts or more present. If it's a one belt setup it has one tensioner. Are you having trouble replacing a belt. Most auto parts stores will print you a belt diagram free of charge. Hope this helps. Chris

5 Related Answers

Anonymous

  • 71 Answers
  • Posted on Aug 22, 2008

SOURCE: Loud squealing sound in my engine

hey

Its possibly the belt!!! did you change that to?

Damien

Ad

Anonymous

  • 74 Answers
  • Posted on Nov 18, 2008

SOURCE: 1997 Jeep wrangler

Clock spring mech is prob bad, first easy check is remove airbag 2 8mm bolt from back side of wheel make sure wires are still connected if they are good the clock spring mech is bad you can use a steering wheel puller to remove wheel and clock spring mech just snaps out and has 2 plugs on it, I have 2 if you need one.

Anonymous

  • 6982 Answers
  • Posted on Jan 17, 2009

SOURCE: Loud squealing sound in my engine

Try removing the belt and turning each pulley by hand. If everything is smooth and free, with the belt still off, drive down the block once and see if the noise is there (this will eliminate all rotating accessories on the front). If you hear the noise, then there is a problem deeper inside. Oil pressure is good? Dont' forget when doing this, you will have no power steering, so be careful.

Anonymous

  • 1071 Answers
  • Posted on Aug 19, 2009

SOURCE: Jeep 1997 Wrangler. Gear shifting very hard

synchronizers are going bad a used trans would be cheaper than a rebuild due to the labor involved

Anonymous

  • 7353 Answers
  • Posted on Apr 23, 2010

SOURCE: engine diagram 1997 jeep wrangler SE

So how do you know you need one if you dont know where it is?? Oil pumps rarely go bad unless the engine is sludged from lack of maintenence. After you take the oil pan off, its there hanging down. Make sure you clean or replace the pick up tube. I'm sure you can google up torque specs, for the bolts. Usually there is major engine damage by the time you figure out that there is lack of oil pressure. I would get a professionals opinion before you waste time and money replaicing the oil pump. If the engine has any unusual noise or knocking, its too late.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Replace idler pulley on a 1990 jeep wrangler

It might look like it will with the belt off.. Once the belt is on, the spring will put tension on the belt and will ride on the pulley. To answer your question..yes there is a spring in the pulley bracket
1helpful
2answers

Removing the Serpentine Belt

Tensioner is either on alternator or power steering pump. release tension and remove belt. draw a diagram if you do not have a manual or indicator chart under bonnett
0helpful
1answer

Setting belt tension on 1993 jeep wrangler 6 cyclinder

Rule of thumb is that you should have just a bit less than one inch of deflection at the center of the longest run between pulleys. Check it again in a few days and re-adjust if necessary (usually not).
1helpful
1answer

Replace Drive Belt tensioner on 1999 Jeep Wrangler

The tensioner can be replaced as just the pulley, by removing the center bolt on this pulley, to release thee tension loosen center bolt then loosentension bolt on top of the bracket.
5helpful
1answer

How do i replace serpentine belt on 1997 jeep wrangler

Adjustment is made by loosening the power steering pump. There is a transverse long bolt (jack bolt) right under the pump that is used for adjustment.
6helpful
2answers

NEED TO TIGHTEN FAN BELT ON 1997 JEEP WRANGLER

If a 6cyl, from the front of engine, loosen the idler pulley with a 15mm wrench. It's on the left side of the engine. Then from the top, use a 15mm socket on a 6 inch extension, and tighten the adjustment bolt that is mounted diagonally just behind the idler pulley. takes alot of turns to tighten the belt. Then retighten the idler pulley bolt with wrench.
1helpful
1answer

How to replace a serpentine belt on 1998 jeep wrangler

Should be the pulley underneath the power steering pulley. Loosen the nut, then back the bolt down the loosen the belt, tighten the bolt to tighten belt.
0helpful
1answer

I can't take off or put on a new serpentine belt on 91 yj

you need to loosen the alternator bolts then turn the bolt under the alternator to relieve tension on the belt
0helpful
2answers

Loud squealing sound in my engine

hey

Its possibly the belt!!! did you change that to?

Damien
Not finding what you are looking for?

129 views

Ask a Question

Usually answered in minutes!

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...