I hit the lock button the lights flash put acadia dont start

your on the right track! your blend door is broken or your blend door actuator is broken.

Try adjusting the latch mechanism.

You might just have a wire loose somewhere. My 96 Cadi did that a couple of times lastyear, then it was fine. Hasn't done it since.` So, who knows! Sorry, not much help to you.

If it is a factory remote start system. Then Press the "Lock" button, then press and hold the "Clockwise Arrow" button till the parking lights flash.

programing a Nissan remote , is hidden secret by Nissan Dealers. As a Nissan Technician i will share it.

Just get in your vech , close all doors. Using your power lock switch , lock all doors. After doors are locked take your Ignition Key and insert it and remove it from ignition switch in a slow fashion , but consitant pace. (97 and earlyer are fast) When you see the hazzard lights flash, put key in ignition switch and turn to the On postion .. Do NOT CRANK or you will have to Start over .. After in the On postion .. Hit the Lock button on remote... Hazzard lights should flash..( note..you have to reprogram all remotes when adding a new one , if you don't your old remotes will not work ) If your doing just the one , turn igntion switch off and unlock door and get out and try it. If you are doing more than one. While still in Vech with Key on . After you hit the Lock button on Remote and hazzard light flashed .. with key still on .. use master lock switch unlock doors and relock and then hit Second Remote, Lights should flash again , repeat if adding a 3rd remote.. after done just turn key off and unlock door and get out and try.

Check the air bag sensor. It probably needs replacement

I would turn the key on without starting the car then press and hold the black button till the alarm light flashes.Then turn key off take out of car and try the fob again.

depends on what type of top you have (full power or power assisted).

if power assisted, then release the latches on the inside where the top meets the windshield, then hit the button on the lower dash (its near the button for the heated seats & traction control) and give it a little push with your hand to start it folding. it has a picture of a side window & top on it. pushing it one way lowers the top. you have to be in park (or drive with foot on brake) to lower it. hold the switch down, the side windows will lower a bit and the top will begin to move. keep holding it till the top tucks under the boot and the windows begin to go back up, then release it. if the light on this button is not flashing when you release it, then the top is tucked away properly. if still flashing, then keep it depressed until the top folding sequence is complete.

if a fully automatic top (you will not have latch releases on the top where it meets the windshield), then simply hit the button as described above. no need to push on the top during the beginning sequence. keep holding it until the windows begin to go back up, then release it.

for both, watch the top as it tucks into the boot. sometimes if the top is not properly aligned, the top cloth may not tuck correctly and may require some help from you. the sequence can be stopped any time, but the red light on this button will flash.

to put it back up, simply hit the button in the opposite manner and the sequence will start with the rear boot lifting up first. fully auto tops will lock automatically to the windshield. power assisted tops will require to lock the top. if red light on this button still flashes when released, then the sequence is not complete or has encountered an error.

hope this worked for you.

Just get in your vech , close all doors. Using your power lock switch , lock all doors. After doors are locked take your Ignition Key and insert it and remove it from ignition switch in a slow fashion , but consitant pace. (97 and earlyer are fast) When you see the hazzard lights flash, put key in ignition switch and turn to the On postion .. Do NOT CRANK or you will have to Start over .. After in the On postion .. Hit the Lock button on remote... Hazzard lights should flash..( note..you have to reprogram all remotes when adding a new one , if you don't your old remotes will not work ) If your doing just the one , turn igntion switch off and unlock door and get out and try it. If you are doing more than one. While still in Vech with Key on . After you hit the Lock button on Remote and hazzard light flashed .. with key still on .. use master lock switch unlock doors and relock and then hit Second Remote, Lights should flash again , repeat if adding a 3rd remote.. after done just turn key off and unlock door and get out and try. Good Luck :)

first make sure,that the batter is ok. You will need to have both remotes while doing this.
1: get in and lock the doors with the power door lock
2: insert the key into the ignitoin repeatedly IN and OUT 6 times in a row or just keep doing so, until the hazard flashers flash on the dash board (observe the dash board while inserting key)
3: after the hazadrs flash TURN key into the ACC position/not start.(dash will light up) DO NOT START
4: with the key in ACC position, hit lock button on the remote. That will program that remote.
5: to program the other remote simply unlock the door with the door lock switch and relock it with the swithc and hit the other remote button.
6: done