Question about 2004 Ford Crown Victoria
Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear
1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION
NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.how do you remove right rear axle on a 2004 ford c - sra~us~en~file=ani_caut.gif~gen~ref.gifa.net/uploads/images/sra~us~en~file=ani_caut.gif~gen~ref.gif" alt="sra~us~en~file=ani_caut.gif~gen~ref.gif" class="h_mi" /> CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
NOTE: Axle housing cover must behow do you remove right rear axle on a 2004 ford c - sra~us~en~file=ani_caut.gif~gen~ref.giftion of the silicone rubber or new silicone rubber must be applied.
CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
Rear Disc Brake Caliper Anchor Plate
CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
Posted on May 13, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: Rear Axle Removal
if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals
Posted on May 30, 2008
YOU NEED A HAYNES OR CHILTON REPAIR MANUAL.TO REMOVE REAR AXLE YOU HAVE TO REMOVE REAR DIFFERENTIAL COVER AND GASKET.YOUR DIFFERENTIAL HAS EITHER PINION SHAFT LOCKING SCREWS OR C - LOCKS.THEY HAVE TO REMOVED BEFORE AXLE SHAFT WILL COME OUT.
Posted on Mar 04, 2010
ok then here is the procedure
1 take off the axle nut
2 on the lower control arm you will find a large nut and bolt i belive the nut is a 21mm and the bolt side is an 18mm. this bolt is the one at the knuckle near the brakes. remove it
3 you will need to pull the knuckle out of the way or a helper to pull the knuckle out of the way so you can slip the axle out of the knuckle.( its a tight fit but there is room to slip it out.)
4 use a pry bar to pop the axle free of the diff. hosing its held in by a spring clip make sure the clip comes out with the axle if it gets stuck inside you will have to fish it out.
5 use a pry bar or screwdriver to pry seal out of housing then use a flat object that contacts the entire rim of the new seal so it can evenly be installed with out getting smashed and tap it in with a hammer. ( a good trick here is to use some grease and pack it into the new seal where the spring is this will prevent the spring from being shocked out of the seal during instalation . the spring keeps tension on the rubber in the seal so it stays tight to the shaft it is sealing.)
6 then revers the above steps. also make sure you are using the right gear lube it will most likely be 75w-140 but make sure you check your owners manual will tell you if it doesnt say on the diff cover. you can cause a lot of damage if you put in the wrong thing. and make sure you feel the axle spring clip snap into place.
as a note there are two types of axle seals that are used on these so if the new seal looks different than the old seal then the folliowing will be important to you.the seals on these have been redesigned so if you axle has what looks like a cup or dust cover pressed onto the shaft where it goes into the diff the new style does not use this and it will prevent the axle form going in all the way so the spring clip will not lock in and you will have a leak. so you will have to remove it and install the axle without it.
Posted on Mar 22, 2009
SOURCE: Rear Axle Seal Replacement
remove rear tires, then remove brake calipers and rotors, then remove the 4 nuts (each side) that hold the axle shafts to the axle tube (located around the axle tube behind the backing plate) then using a slide hammer pull the axle shafts out, next using a die grinder and an air hammer get he retainer collar and the bearing off (without damaging the axle shaft) then remove the seal and the outer race which will still be in the housing. next put it all back together, make sure the plate with the studs is still on then slide the seal, bearing, then retainer on (all new parts) and using a press push them all the way back on. then is simple reassembly.
Posted on Apr 22, 2009
SOURCE: rear axle leaking
Block the front tires. Break the rear lugs loose. Jack up the rear of the truck at the center if possible. remove the wheels & brake drums. Remove the brake shoes,return springs & all the other hardware. Remove the differential cover & drain oil. If you have a posi the next step sucks. You need to remove the threaded pin from the housing & remove the axle retaining clips. All the while,being carefull of the spring in the posi unit. If no posi,then same procedure,minus the "pucker factor". After the axle is out,take a large flat blade screw driver or pry bar & pop the seal out. Keep in mind the axle bearing is probably gone too , so that's another procedure. Keep it apart,you'll be glad you did.
Posted on Jun 23, 2009
Tips for a great answer:
Aug 19, 2018 | Ford F-250 Cars & Trucks
Sep 18, 2014 | 1997 Ford Crown Victoria
Nov 04, 2012 | 1993 Ford Crown Victoria
May 18, 2011 | Ford Explorer Cars & Trucks
Dec 31, 2010 | 2004 Ford F150
May 25, 2010 | 1999 Ford Explorer
Mar 18, 2010 | 1999 Ford Crown Victoria
Apr 10, 2009 | 2004 Ford GT
Feb 22, 2009 | 1999 Isuzu Rodeo
Jul 26, 2008 | 2004 Ford Crown Victoria
6,777 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: