Instructions on replacing rear axle end oil seals 90 silverado pu

Diane, links below show how to remove axles on Chevy trucks.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
remove rear axel on 1993 chevy g20
How To Change Your Rear Axel Seal Chevy Silverado
How To install Replace rear Axle 2000 06 Chevy Suburban Silverado GMC...

Watch the You Tube Video

Remove the rear axle cover
Remove the carrier bolt & pin
Push the axles in
Remove the C-Clips
Pull the Axles
R & R the housing end seals

they come out the same way you just need to fight with the clips a little harder

First i would check to see if the axle air vent was clear if its not the oil is vary heavy and expands a lot this will build up pressure inside the houseing and cause the axle seals to leak if you can clear it the problem may fix it self its 80 90 weight oil thats thick stuff. If not you need to remove the rear wheels and brake drums then you have to remove the cover from the rear carriar catch the oil. Look inside the carriar houseing you will see the ends of the axles theres a small clip on each axle called a c clip remove them you can pull them out with your fingers. Then you can slide the axles out past the brake plates pry the seals out you might as well replace the bearings when your doing but thats up to you. Lube and install the bearings then the new seals you will need new seals lube the seal lips and vary carefuly slide the axle in taking care not to damage the seal install the c clip do the other side put a new gasket on the rear carriar tighten bolts to 20 ft lbs. Refill carriar 80 90 weight oil through filler plug on the side of the houseing until it just starts to run out hole put the plug in the rear drums on and wheels

There are two types of gear oil per say in a car/truck. Did you mean the engine oil or oil for the axle? Either way the engine oil is in the manual for the car, and for an axle you want at least an 80-90w oil.

hope this helps.

Replace the seal forthwith. leaking grease will wreck your brakes and that is dangerous.

Typically rear ends take 90 weight oil, it goes in through a plug near the center of the rear end, fill to bottom of the hole, with rear end level. You can get a suction gun to **** some fluid and pump into the rear end.

If what you see leaking is very oily and does not evaporate, likely it is an axle seal. If there are no leaks in the brake system, that's the only thing back there that can leak. If the axle bearing is going away, it can damage the seal so make sure you look for small shiny metal flakes behind the seal when you replace it or you will be doing the job again very soon. Can't remember...that IS rear wheel drive right?

First check level of oil in rear end housing, if low, pull drums & see if any axle seals are leaking.
If you want info on doing axle bearings, get back to us.

Not that difficult, raise and support the rear of the truck and remove the wheels. Might as well replace both sides so you know you have new seals, remove the differential cover and drain the fluid. Once differential is opened and cleaned , remove the axle "C" clip that hold the axle in place and slide the axle out. Once the axle is out remove the wheel seal and clean around the area. This would be a good time to replace the wheel bearing too since you have access to them and there not that expensive. Install the new bearing and seal, note make sure you oiled the bearing and seal before installing it back and take care when installing the axle back in and "C: clip. Use RTV silicon gasket maker to seal the differential cover and wheels back on and lower. If your lazy like i am, you can drain the differential fluid and replace it with a 50/50 mix with gear oil and Lucas engine oil additives. That may stop the leak and get you a few more miles. You gear oil is 75W-90 and the capacity is 2.6 liters and 3.6 liters if you have the 11.50 Ring gear. Good luck and hope this helps. 

Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.

1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .
   
   
   
   
   

1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.

1. Drain rear axle lubricant by removing the axle housing cover .

1. Remove differential pinion shaft lock pin and differential pinion shaft .
   
   
   
   

1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .
   
   
   
   

1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.

Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.

1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .

1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .

1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.
   
   
   
   
   NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
   CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
   

1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).
   
   
   
   

1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).

1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).

1. Install rear disc brake caliper and rear disc brake rotor .

1. Install wheels and tires.

---------------------------------------------------------

1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.
   
   Rear Disc Brake Caliper Anchor Plate
   
   
   
   
   

1. Lubricate the rear wheel bearing with Rear Axle Lubricant.
   
   
   
   

1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.
   
   
   
   CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
   

1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .
   
   
   
   

1. Install axle shafts as outlined.