Malfunctioned; unplugged, plugged back in, seems OK. Yes?

How to change spark plugs hyundai accent 01 - 05 - YouTube

? 3:18
https://www.youtube.com/watch?v=tU2vwisJ7v4
Feb 16, 2012 - Uploaded by PNBNC
I filmed this right after changing my old plugs, I figured it was easy enough to film and some people can profit from it. for a ... Coil, you mean wire lol ... When you go to put the spark plug back in, never start it with the ratchet.

How To Replace Change Install Spark Plugs 2001-06 ...

? 3:17
https://www.youtube.com/watch?v=yVV2KcPDFIo
May 14, 2013 - Uploaded by 1A Auto Parts
... spark plugs. This video is applicable to the 2001, 2002, 2... ...spark plugs. This video is applicable to the 2001, 2002, 2003, 2004, 2005, 2006 Hyundai Elantra 2.0L. ... +queentonks A little know-how can go a long way. We're glad ... When do you think is good to replace my spark plugs wires? My spark ...
2001 Hyundai Accent Firing Order: Engine Mechanical ...www.2carpros.com/.../hyundai-accent-2001-hyundai-accent-firing-orderApr 23, 2009 - Engine Mechanical problem 2001 Hyundai Accent 4 cyl Two Wheel Drive Manual 95000 ... Now I'm trying to figure out how they go back on. How do I find out the Engine Firing Order for my car - Hyundai Accent 2001 1.5L?Which is cylinder 1 - 1.6 Accent - Hyundai Forum: Hyundai ...www.hyundaiperformance.com/.../16837-cylinder-1-1-6-accent.htmlJan 13, 2003 - 3 posts - ‎3 authorsFrom what I read though, the coil pack is configured as 1 4 2 3. I'm assuming the first wire on the coil pack goes to cylinder 1. Can anyone ...

With the wire to the compressor unplugged, see if 12 volts is present at the plug. If voltage is present, then check the terminals on the compressor clutch for continuity. ( voltage meter in beep mode) Volt meter will beep if clutch coil is good, no beep, clutch coil is bad. Also low Freon pressure will disable clutch via low pressure switch at the accumulator. Always check pressure and add Freon to low side(large tubing) A freeze hazard and explosion hazard (high side, small tubing) exist when handling Freon. Wear safety glasses and be careful. Also cooling fans should run continuous when A/C is on

1. the fuel gauge needle spindle seems to be struck.
2. and check sensor for scales formation.

Seems like your transmission has failed. Either some syncros or bearings are worn out. Its sounds like its time to either have it rebuilt or replaced.

hi from uk the part you mention is the brake stop light switch it has a plug on 2xwire plug it operates by as pedal is pressed the plunger of switch moves out and connects the 2xwire circuit and so brake lights operate this switch simply unscrews from the pedal box/carriage after plug removed then the new switch screwed in place and with b/pedal off the switch is screwed to a point that if you press pedal down approx 1/2 " the switch plunger moves out and b/lights come on this is trial/error untill you are happy with the pedal movement down till lights operate SIMPLE ! hope this helps?

Have you checked the fuse?

On the 03 Accent, there is only one relay which supplies power to both circuits. The 'distribution' of power is controled by the multi-function switch (turn signal switch).
As you can see in this wiring schematic/diagram.

I have an '03 Hyundai Accent 1600cc. I am told by the techies at the local dealer, the fuel filter is ON the fuel tank. You gain access to it by removing the back seat, then opening the panel beneath the back seat. Replace the filter, screw the panel back onto the floor and the job is done....

Check for headlight relay and fuse. Some cars have separate circuits for head light flasher and normal high/low beam. From your description, I would suspect a bad connection to/from relay or relay itself.

Sounds like your brake diaphragm in the rear that puts pressure on the pads has malfunctioned, if you know where your brake bleeding plug is you can maybe release the pressure real quick then tighten it back, but, it sounds like a repair shop unless you work on them yourself.