1999 Pontiac Montana Logo

Related Topics:

A
Anonymous Posted on Dec 02, 2013

Knock sensor location 99 pontiac montana

Can t find it should I take off the plenum

5 Related Answers

Anonymous

  • 3 Answers
  • Posted on Jan 17, 2009

SOURCE: where is the ecu in a 99 pontiac montana van

The ecu is located under the Air filter housing on my 99 montana

Ad

Anonymous

  • 179 Answers
  • Posted on Mar 28, 2009

SOURCE: coolant sensor

According to mitchell on demand there is no low coolant tep sensor, only standard ECT sensor.

Anonymous

  • 54 Answers
  • Posted on Mar 31, 2009

SOURCE: NEED TO KNOW WHERE THE OXYGEN SENSORS ARE LOCATED

hi im wes
all o2 sensors are in the exaust you have one before the cat converter and one after
thanks
ps please rate me

Anonymous

  • 31 Answers
  • Posted on Jul 10, 2009

SOURCE: 2000 pontiac montana o2 sensor bank one location

if there is only two it probly the one up buy the motor call the dealer they have the manual

Anonymous

  • 4803 Answers
  • Posted on Oct 11, 2009

SOURCE: The Driver Information Center (DIC) 99 Montana is out

I am assuming that the DIC does not "power-up" at all.

Check your owner's manual to see which fuse powers the DIC. If the fuse is OK, you need to get your hands on a wiring diagram and remove the DIC from the dash so you can check to see if you have a good ground on the ground wire to the DIC. Then check to make sure you have battery voltage to the B+ circuit to the DIC. If the proper voltage and ground are present, you will have to take the DIC to your local dealer for repair. Many GM dealers have an exchange program where you can turn your old DIC in and get a "remanufactured" one on the spot. Others will send your DIC out for repair and call you when it is returned to them.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

What code p0332 is for my 05 pontiac montana sv6 3.5 engine??

That is for the knock sensor, bank 2. With transverse engine, the front bank on your vehicle should be bank two. You have more than one knock sensor, one for each bank.
26020766-q5x51mpy1oz0givoejoxaaqf-5-0.jpg
0helpful
1answer

2000 Pontiac Montana that starts and runs fine for 7-12 min then looses throttle power. Sputters at 1k-2k for 10-15 min then runs fine for 7-15 min then runs even worse, wills sputter at 750+ rpm.

3.4L Engine Sensor Location Pictures and Comments

www.greatautohelp.com/sensor-location/3400-Sensor-Comments-2.html
the battery for a few minutes to see if that helped. ... If the gauge is at half way on the first start, then yes, either the ... All of a sudden I could not accelerate and the carelost power. ... But once the temperature gauge goes to normal it will run fine. ... 3-7-12. I replaced head gaskets and intake gaskets on my 2000 Pontiac 3.4L

[PDF]2000 Pontiac Montana Owners Manual - GM Extended ...


1helpful
1answer

Where is the location of 02 sensor for bank 1 sensor 1 on a 2001 Pontiac Montana?

Bank 1 sensor 1 means the first oxygen sensor closest to the motor. The location is probably in the exhaust manifold, if not then follow the pipe from there and it's the first one you find. Hope this helps
0helpful
1answer

No dash heat 2001 montana

Could be an actuator motor under the dash that opens and closes the door. It will be located on the heater plenum.
0helpful
1answer

I need to replace the fuel vapor pressure sensor in a 2000 pontiac montana where is the sensor located.

In the rear ,in front of fuel tank

Need an EVAP Diagram to locate it

Have to get one from a repair shops
data base
1helpful
3answers

2002 pontiac montana with an occational starting problem

Go to Autozone and they will check your cars trouble codes for free and tell you what part you will need to replace. They are usually right 99% of the time.The crankshaft position sensor located behind the harmonic balancer maybe be bad. There is another crankshaft position sensor located on the engine block above and to the right of the oil filter. Or it could be the power train control module located to the right of the air cleaner box. This information is for the V6 3.4 engine. Buy the repair manual for your Montana and go to the engine performance section. The manual costs about $26.00
0helpful
2answers
1helpful
2answers

92 lexus es300 knock sensor

Need to remove the upper and lower air intake manifold.  There are two knock sensors for the front and rear pistons banks.  If you plan to do this yourself it is about 1 to 2 hours.  While you are at it, there is a short coolant bypass hose sitting in the same spot, replace it.  Another problem with the knock sensor is the wire harness used to connect the two knock sensors into one connection sometimes wears out and contacts the metal on the engine causing false signals to the ECM, so replace this cable also.
Just did this last summer on my 99 ES300.  Pretty easy.
DIYr
0helpful
1answer

Knocking in engine

Please check your Knock Sensor, Spark Plugs and Wireset (if not done already). Below I will list the website on how to change the Knock Sensor.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528009603b#hd1-1-1

Hope you see what you are your looking for! Good Luck!
If you have any more problems let me know.

Thank you for using Fix Ya!

Don't forget to rate the overall satisfaction of this answer!
2helpful
2answers

Where is the ecu in a 99 pontiac montana van

The ecu is located under the Air filter housing on my 99 montana
Not finding what you are looking for?

144 views

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...